密著力試驗 的英文怎麼說
中文拼音 [mìzhāolìshìyàn]
密著力試驗
英文
adhesion test- 密 : Ⅰ名詞1 (秘密) secret 2 [紡織] (密度) density 3 (姓氏) a surname Ⅱ形容詞1 (距離近; 空隙小)...
- 著 : 著助詞1. (表示動作的持續) 2. (表示狀態的持續) 3. (用在動詞或表示程度的形容詞後面, 加強命令或囑咐的語氣) 4. (加在某些動詞後面, 使變成介詞)
- 力 : Ⅰ名1 (力量; 能力) power; strength; ability; capacity 2 [物理學] (改變物體運動狀態的作用) forc...
- 試 : 名詞(古代占卜用的器具) astrolabe
- 驗 : 動詞1. (察看; 查考) examine; check; test 2. (產生預期的效果) prove effective; produce the expected result
- 著力 : put forth effort; exert oneself
- 試驗 : trial; experiment; test
-
Tensile tests of carbon filament yarn shows at high strain rate that the mechanical behavior of carbon fiber bundles are insensitive to strain rate, i. e., the failure stress strain and elastic modulus are not increased with the rising of strain - rate. however, the fractograph of carbon fiber is rate - dependent. the fractograph of carbon will become smooth from coarse as the strain rate increases
通過對碳纖維束的沖擊拉伸試驗表明,雖然碳纖維束的力學性能與應變率基本上是不相關的,即隨著應變率的增大,碳纖維束的初始模量、破壞應力及其失效應變都變化不大,但碳纖維束的破壞斷口與沖擊拉伸實驗的應變率密切相關。No matter what the relative density, confining pressure, liquefaction severities are, the post - liquefaction deformation will show the same characteristic. the factors mentioned above have their own affecting ways. a lot of tests have been done to investigate the reconsolidation characteristics of sand after dynamic loading
砂土液化后模量隨應變增加而增大的特性與常規三軸試驗中模量隨應變增大而減小的特性不同,相對密實度、液化度、初始有效固結壓力等都以特定的方式對影響著液化后的變形特性。( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal
( 3 )針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題,如較大的殘余應力,製件中存在著微裂紋、微孔洞等缺陷,初步提出掃描路徑的規劃,並採用幾種不同的掃描方式進行燒結試驗,發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構,採用短邊同向路徑制備的試樣其顯微硬度最高,而採用變向掃描(垂直)路徑制備的試樣緻密性最好。The pseudo - dynamic test gives the model ' s earthquake response, failure characteristic and special seismic property, unveil the structure ' s failure procedure of " low density setin block ' s break - slab rib ' s break - end post ' s concrete craze - end post ' s steel bar yielding ", providing full and accurate experimental information to establish the seismic design method. the slab ' s crack discrimination condition is prescribe. the extreme shear strength bearing moment, shear and pressure synchronously shows the bearing capacity components and change in slab ' s failure process
提出了密肋復合墻體開裂的判別條件;對于墻體在彎剪壓耦合作用下的極限抗剪承載力性能,分析了其構成因素及其隨破壞過程的變化規律;在試驗研究和數值分析的基礎上,提出密肋復合墻體抗剪和抗彎承載力表達式,並對典型墻體多遇地震作用下的承載力可靠指標進行了驗算;對影響墻體抗剪能力的各種因素進行了顯著性分析。Hockman standard test method for adhesion and cohesion of elastomeric joint sealants under cyclic movement hockman cycle
在循環運動條件下彈性接合密封料的粘著性和粘結力的標準試驗方法During the last 10 years, with the acquisition of much valuable intensive observations in a series of typhoon field experiments, the improvement of the weather monitoring network, the upgrade of atmospheric numerical models and the rapid development of computer powers, many problems in typhoon heavy rainfall research are further studied, such as the interaction between typhoons and mid - latitude weather systems, the interaction between typhoons and topography and underlying surface, the mesoscales of typhoons and the dynamics and so on
近10年來,隨著我國一系列臺風外場科學試驗加密觀測數據的獲得、天氣監測網的逐步完善、大氣模式的改進以及電子計算機的飛速發展,臺風與中緯度系統的相互作用、臺風與地形下墊面相互作用、臺風中小尺度及其動力學等方面均得到深入研究。分享友人