延性區 的英文怎麼說

中文拼音 [yánxìngqū]
延性區 英文
thumb nail
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 區 : 區名詞（姓氏） a surname
  1. Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete

    通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。
  2. The research shows that : 1 ) the ductility of the hsc bending members constructed is much greater than 5 ; 2 ) increasing the vertical links and distribution steel can increase the deflection under ultimate moment ; 3 ) with appropriate compressive bars, vertical links and distribution steel the increase of moment after yield and the decrease of moment under ultimate moment can be ignored, so the ductility of the hsc bending member is much larger ; 3 ) the width / depth ratio of hsc bending member has no obvious effect on the ultimate compressive strain of concrete ; 4 ) the method used here to calculate the deflection is applicable ; 5 ) the location of crack coincides with the location of vertical links and distribution steel ; 6 ) the bending property of the hsc structure under the blast load can meet the demand of protective engineering

    研究表明：本文研究的梁、板構件的延性比遠大於5 ；增加箍筋（鉤筋、分佈筋）含量，可以提高壓區混凝土剝落時的撓度；在適當的受壓筋、箍筋（鉤筋、分佈筋）含量下，可以忽略壓區混凝土剝落瞬間的承載力下降，從而大大提高構件的延性；受彎構件的寬高比對壓區混凝土極限應變的影響不明顯；受彎構件的裂縫間距受箍筋（鉤筋、分佈筋）的布置影響；文中所用的承載力和變形計算方法是可行的。化爆試驗表明，高強混凝土構件的動載抗彎性能能夠滿足防護結構的要求。
  3. Predictions were made on the ductility of the joint core when shear compression ratio, reinforcement contant and axial force ratio were different

    進一步利用jap程序預測了不同剪壓比，不同配筋特徵值及不同軸壓比條件下節點區的延性變化規律。
  4. Its hysteretic curve is plumper, its ductility coefficient and energy dissipation capacity have been improved remarkably. the inclined staff of the steel bar truss has a restraining faction to the development of the crack, and the phenomena is that there has more crak and larger distributing area on the shear wall, which is an important token of the improved seismic capacity. concealed steel bar truss has the faction of increasing the height of plastic hinge area, which is another important token of

    研究結果表明:內藏鋼桁架高剪力墻與普通高剪力墻相比:屈服荷載和極限荷載均比顯著提高;屈服剛度明顯提高;其滯回環相對飽滿，延性系數及耗能能力顯著提高;內藏鋼桁架高剪力墻，其鋼桁架斜桿對裂縫發展有控製作用，現象是墻體上的裂縫較多、分佈域較廣，這是抗震耗能能力增強的重要表徵;內藏鋼桁架高剪力墻有增大底部塑性耗能區域的作用，這是抗震耗能能力增強的另一重要表徵;內藏鋼桁架還有顯著提高抵抗剪力墻基地剪切滑移能力的作用。
  5. Based on the results of experimental research, we can find that the construction method of joints zone are feasible and safe, the joints between concrete - filled steel tubular core columns and prestressed concrete beams have good ductility and good energy dissipation, and the concrete - filled steel tubular core columns can raise the shear strength of core area of joints and the bending strength of the column ends

    試驗研究發現，針對該節點所設計的構造處理方式是可行的、安全的，鋼管混凝土核心柱與預應力混凝土梁框架節點有著很好的延性和能量耗散能力，由於柱為鋼管混凝土核心柱，大大提高了節點核心區的抗剪承載力，同時也使柱端抗彎承載力得到加強。
  6. The problem two is the stirrup in the core of beam - column joint was insufficient because of designing or construction. so the shear capacity and ductility of beam - column joint will decrease

    框架節點核芯區柱箍漏放或數量不足，引起節點抗剪承載力降低，延性不足。
  7. If the quantity of the beam stirrups is not enough, the wide beam would have more crack in the joint area thus decrease bearing capacity and ductility of joints

    如果節點區的寬梁箍筋數量不足，寬梁在節點區將出現較多斜裂縫，最終使結構的承載力和延性變差。
  8. The main contents are as follows. by the experiments of two joints under low - reversed cyclic loading, the paper analyzes the failure pattern, energy dissipation, ductility and cracking in the joint cores, evaluates the seismic performances and anti - crack behaviors of the joints, and deduces the anti - crack formula of the subassemblage and prestressed frame joint. through the fini te element analysis software ansys, the paper analyzes the specimens nonlinearly, and the theoretical analysis results are well consistent with those of the experiment

    主要內容包括：通過兩榀節點在低周反復荷載作用下的試驗，分析其破壞形態、耗能能力、延性性能和節點核芯區裂縫開展情況，評估節點的抗震性能和抗裂能力，推導出預壓裝配式框架節點的抗裂驗算公式；並運用ansys對試驗中的節點進行了非線性分析，計算結果與試驗結果基本吻合。
  9. The following conclusions are reached. ( 1 ) the relative height compressive zone of section or the axial force is bigger, the rotational capacity of the section is weaker

    得出了以下主要結論： （ 1 ）截面相對受壓區高度、截面所受軸力顯著地影響預應力框架梁截面的延性。
  10. Histological changes of osteoblast mode of pseudo growth plate in bone lengthening area

    骨延長區假性生長板及其成骨方式的組織學觀察
  11. Refuge story is made feasible use, while the architecture space is not occupied. stiffness strengthened story with " proper stiffness " is designed. the problem of the lateral stiffness insufficiency of the super high - rise building is solved, and the seismic ductility is increased in the seismic region

    最後，論文聯系實際工程，從結構概念設計角度較為成功的應用了剛性加強層的設計理念，在不佔用建築空間前提下，合理利用了建築避難層，設計了「適宜剛度」的剛性加強層，巧妙解決了超高層建築結構抗側剛度不足的問題，同時確保了抗震地區超高層建築結構的抗震延性，使結構體系安全、經濟、合理。
  12. The advantages of circular steel tubular columns filled with steel - reinforced concrete are discussed by comparison to reinforced concrete columns. from the above analysis, we can conclude that circular steel tubular columns filled with steel - reinforced concrete which have high load - carrying capacity as well as excellent ductility can be used widely especially in the buildings of strong seismic intensity zone

    從試驗研究、理論分析和試設計的結果，可以看出鋼骨?鋼管混凝土柱具有很高的承載力和很高的延性，這種柱具有廣泛的應用前景，特別適用於高地震烈度區柱的設計。
  13. At last, with the program, 18 one - storey and one - span prestressed frames are simulated. some conclusions are reached with the taking into account the, secondary moment and types of load applying : ( 1 ) the in the beam affects the ductility of the section and rotary property of the plastic hinge. so total coefficient of the modulation of moment becomes less with the becoming bigger

    最後，本文利用編制的非線性程序，模擬了18榀單層單跨預應力框架，重點研究截面相對受壓區高度、次彎矩、加載方式對塑性內力重分佈和彎矩調幅的影響，從中得出了以下主要的結論和規律： （ 1 ）框架梁相對受壓區高度在很大程度上反映了截面的延性，體現了塑性鉸的轉動能力，框架的總彎矩調幅系數隨著相對受壓區高度的增大而減小。
  14. Based on the tests, the advised formula of normal section bearing capacity and inclined section bearing capacity of high strengthen concrete frame columns are put forward, and the limit of axial compressive ratio and the minimum stirrup ratio in the encrypted region which meet ductility requirement to c60 concrete frame columns are given

    在試驗研究的基礎上，提出高強混凝土框架柱正截面和斜截面承載力計算的建議公式，且給出了滿足延性要求的c60混凝土框架柱軸壓比限值和箍筋加密區箍筋的最小體積配箍率。
  15. Telecommunications - network and customer installation interfaces - analog voicegrade switched access lines with the call waiting, distinctive call waiting, or calling identity delivery on call waiting feature

    電信.網路和用戶裝置間的介面.帶呼叫延時區別性呼叫延時或呼叫延時中呼叫身份傳送功能的模擬音頻轉換訪問線路
  16. This paper has put forward such one, i. e. to use the dimensional angle iron framework to strengthen the center of the knot in order to add its degree of toughness and stiffness, improve its crack load and aggrandize its ultimate deformation

    本文提出了一種提高節點抗震性能的新方法? ?用空間角鋼骨架對節點核心區進行加強，以增大節點的強度、剛度，提高節點的抗剪、抗裂性能，並增大節點的極限變形能力及延性性能。
  17. The first two mechanisms transfer joint shear, while the third inecha - nism provide ductility and energy dissipation capacity by confining the joint core concrete from lateral expansion

    前兩個機構直接傳遞節點剪力，后一個機構則通過約束節點核心區混凝土的側向膨脹提高節點的延性和耗能能力。
  18. Appling the hollow shear wall to multi - story and sub - high rise residences, these can be come into being that include reducing self - weight, stiffness, earthquake action, and improving ductile, saving material and energy, so building ' s integration economy target can be fallen

    將這種墻用於地震區的多層和小高層房屋，可以減輕自重，減小剛度，降低地震作用，提高延性，節約材料，並且節能效果好，降低了房屋的綜合經濟指標。
  19. So its suggested that the ratio of building height and building width for the staggered truss steel framing is better less than 5 in the region of seismic fortification intensity is 7 and less than 4 in the region of seismic fortification intensity is 8

    7 ）通過高寬比對鋼結構交錯析架體系的整體延性的影響分析，建議在7度及以下抗震設防地區，鋼結構交錯精架體系的高寬比宜小於5 ;在8度抗震設防地區，鋼結構交錯析架體系的高寬比宜小於4 。
  20. A seismic shear capacity equation for ductility and non - ductility columns is proposed to amount for the reduced shear contribution of concrete as to the increasing of displacement ductility levels. 6. the behavior of columns * transverse displacement within yield hinge regions is also discussed based on truss - arch model. 7. the seismic shear capacity design equation of columns with various ductility levels is proposed in statistic method on the basis of test data collected from japan and china to simplify the equation resulted from truss - arch model

    對國內外試驗資料進行了統計分析，詳細分析了剪跨比、軸壓比及配箍特徵值對框架柱構件抗剪承載力的影響，得到了反復荷載下框架柱塑性鉸區域極限承載力計算的統計公式；在理論推導公式及統計公式的基礎上，參考國內外規范，首次管品武；鋼筋混凝土框架柱塑性鉸區抗剪承載力試驗研究及機理分析提出了鋼筋混凝土框架柱塑性鉸區域剪切承載力抗震延性設計實用公式。
分享友人
分享到 Line

分享到臉書