延性物料 的英文怎麼說
中文拼音 [yánxìngwùliào]
延性物料
英文
ductile material-
A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well
液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。And the impact of processing conditions on the electrochemical performance of the porous sn - cu alloys was investigated. results showed that it was good to add more verdigris and to make the annealing time longer for improving the performance. however, the problem of capacity fading can not be solved completely by this method
並對制備合金材料過程中所添加物質的種類和比例、燒結時間等工藝參數對合金的性能的影響進行了分析，發現添加堿式碳酸銅，並且增大添加比例以及延長燒結時間對電極材料的循環壽命有利，但是不能根本解決容量衰減的問題。Aln is an important compound semiconductor material with wide band - gap, which has wurtzite structure too. because of their many excellent physical properties, aln thin films were applied in blue - uv emitting materials, epitaxy buffer layer, soi material and saw device with ghz band
Aln具有許多優異的物理性能，在藍光、紫外發光材料及熱釋電材料、外延過渡層、 soi材料的絕緣埋層和ghz級聲表面波器件等方面有著重要的應用。This study made a conclusion ? amely in order to realize following the geological target while drilling, on the basis of making a better geological and drilling design for horizontal well, we must make full use of mwd, lwd and integrate logging to carry out lithfacy identifying in real time, the lwd interpretation and formation evaluation, to set up geological model of target formation, to select geosteering marked formation and compare simulative curves with lwd curves f to fix on the drilling direction of bit upper and declination, the position in target oil - gas layer, to revise borehole track in real time, to make it extend in reservoir better interval as possible
研究認為，在做好水平井地質設計和鉆井設計的基礎上，要實現隨鉆跟蹤地質目標鉆井，必須充分利用隨鉆測量、隨鉆測井和錄井等資料，從實時巖性識別、隨鉆測井解釋和地層評價、目標層地質模型建立、導向標志層的選取及模擬曲線對比等方面入手，確定鉆頭上下傾鉆進方向及在目標層中的位置，以實時調整井眼軌跡，使其盡可能在儲層物性較好的部位延伸。1. this product is a new kind machinery induction - type electrical energy appliance. it adopts high coercive force aluminium nickl cobat material to make the special structure magnetic - hanged magnetic - propelled bearing. when it is electrified to operate, interrepulsion is produced between the bearing and the anxle so that it is electrified to operate. interrepulsion is produced between the bearing and the anxle so that it is suspend station. the friction loss is very small. it not only reduces energy exhaustion by a wide mardin, but also prolongs lifetime to 20 years and above
1 dd951型長壽命單相電度表是金雀儀表有限公司新開發的高可靠性民用電度表，本產品系一代機械感應式電能計量器具。採用高矯頑磁力鋁鎳鈷材料制面的特殊結構磁懸磁推軸承，能電動物時軸承與軸之間產生相互斥力合其和處于懸浮狀，運轉磨擦損耗極小，不但便能耗在幅下降，而且壽命可能性延長到二十年以上。In this paper aircraft has made vertical and synthetic detecting flying purposefully on 9. 17, 2003 according to cloud ' s macro and microstructure. vertical layers and representative places of stratiform cloud on 9. 17, 2003 are analyzed using the observational data of particle measurement system ( pms ), combined with satellite data, radar data, and precipitation data on ground. by this we have got cloud ' s microphysical structure and physical process of the natural precipitation, and the physical effect evidence has been testified according to observational data after lco2 seeding
本文用綜合觀測的方法，利用機載pms雲粒子探測系統，根據雲系的宏微觀結構特徵進行有針對性的垂直探測飛行，配合衛星、雷達、地面雨量、雨強計網觀測資料對2003年9月17日延安降水性層狀雲系中那些有代表性的部位或垂直分層做細致的觀測分析，獲得雲系的微物理結構和自然降水形成的物理過程，並用觀測事實來驗證人工增雨引晶催化后的物理響應判據。The ability of being non - inflammable is shown through the fact that the mattress is not inflammable by a burning cigarette ; on fire exposure the mattress does not activate and expand the fire as other materials do ; the mattress rapidly absorbs liquid because it has an openly porous structure, allowing an easy stop of the fire by water
Kymdan床墊的防燃燒性能體現在：點燃的香煙掉到床墊上不會著火：在與火勢接觸時不會造成雄雄大火，而且不象其他物料般迅速將火勢蔓延。由於有通氣孔透氣結構，因此kymdan床墊有迅速吸收的性能，可以容易以水撲滅火種。Sige simox : oxygen ions with high dose were implanted into sige grown directly on silicon substrate for the first time, and sige - oi novel structure was formed successfully with additional high temperature annealing ; it has been confirmed that oxygen implantation with 45kev, 3 1017cm - 2 and annealing at 12500c in ar + 5 % o2 for 5 hours, are fit for the formation of sige - oi structure ; ge loss during the high temperature annealing has been observed, which is originated from ge volatility and ge diffusion ; it has been proposed to use nanoporous layer induced by h + / he + implantation to surppress ge diffusion and to use surface oxidation to overcome the upper limit of sige simox. sige smart - cut : hydrogen ions were implanted into sige material and followed by high temperature process ( 4000c to 7000c ) ; blistering study was done and suggested the possibility of sige layer transfer by smart - cut technology ; it is concluded that the bubble formation is easier in sige than in si, and the strain in sige / si and the difference of binding energy in sige and in si could possibly contribute to this effect. behavior of sige / si implanted with hydrogen : gave a detailed study on sige implanted by beamline or phi hydrogen implantation ; it has been found that great strain is introduced into sige by hydrogen implantation and this strain could be alleviated by high temperature annealing ; both for conditional beamline implantation and piii hydrogen implantation, 600 is appropriate for the post - implantation treatment
Sige - simox工藝方面：首次採用硅（ 100 ）襯底上直接外延的100nm厚sige的樣品中注入高劑量的o離子，通過退火處理成功制備了sige - oi新結構，即sige - simox工藝，證實了以45kev注入3 10 ~ （ 17 ） 7cm ~ （ - 2 ）劑量的氧離子，隨后在氧化層的保護下經1250 ， ar + 5 o _ 2氣氛的高溫退火（ 5小時）過程，可以制備出sige - oi新型材料；實驗中觀察到退火過程中的ge損失現象，分析了其原因是ge揮發（ ge通過表面氧化層以geo揮發性物質的形式進入退火氣氛）和ge擴散（ ge穿過離子注入形成的氧化埋層而進入si襯底中） ，其中ge擴散是主要原因；根據實驗結果及實驗中出現的問題，對下一步工作提出兩個改進的方案：一是通過在si襯底中注入適量h ~ + / he ~ +形成納米孔層來阻斷ge擴散通路，二是可以通過控製表面氧化來調節安止額士淤丈撈要表面sige層中的ge組分，從而部分解決sigeIt is indicated that the hydration process of cement - based materials with slag, fly ash and silica fume is different in some degree from that of neat cement because of the difference in mineral structure and hydration mechanism. the periods of accelerating, decelerating and terminating are prolonged and hydration reaction decelerates. the second peak of rate curve of the heat evolution could be divided into two small peaks, which are contributed to the hydration of clinkers and mineral mixtures at the temperature of 30 but when temperature comes to 50, the two small peaks combine into one and the reaction accelerates
結果表明，與硅酸鹽水泥相比，由於礦物摻合料與水泥熟料在活性和水化機理上的差異，水化歷程有較大的改變：多組分體系誘導期、加速期和衰減期延長，水化反應速率明顯降低；低溫時，水化放熱速率曲線上的第二放熱峰細化成分別對應于熟料和礦物摻合料水化的兩個小峰；高溫時，反應速率加快，雙峰合併；進一步研究發現，摻合料的種類與摻量對水化歷程也有較大的影響；建立了適用於多組分水泥基材料不同水化階段的水化動力學方程。Maifan stone tea wares are made through traditional chinese technique and moderm technology. they are of natural color, simple and classic. they can improve the taste of the tea. long drinking can supplement people with to human minerals and trace elements that are necessary to human body, exclude poisonous substances, wash cells and adjust metabolism, promote blood circulation, benefit to urine, stomach, and liver. the drinkers can gain perfect enjoyment in ta - ste, smell, and vision
該產品用正宗"靈玉"牌中華麥飯石為原料，造型各異.工藝精湛，本產品重點突出工藝性和神奇的保健作用，可沏茶泡酒均可，有益元素迅速溶出，能補充人體所需，促進微循環，調解新陳代謝，清除體內有毒物質，從而達到強身體健體，精力充沛，延年益壽之目的The results show that mno which not be modified can not be use as electrode active materials because of its poor electrochemical activity. meanwhile, the rechargeabilify of mno modified by bi and pb is improved. bismuth could prolong the second electron equivalent discharge and lead could improve the first electron equivalent discharge performance
I44 ）對熱分解產物進行了充放電，循環伏安，恆電流極化， tafe曲線分析，交流阻抗分析，得出未摻雜的mno直接作為電極活性材料，其電化學活性很差，但通過摻bi ， ph進行改性，提高了其可充性， 1的影響主要在於第二電子放電， ph則可以延長第一電于放電The design architecture is a complex comprehensive subject, which involves architecture, sociology, folklore, psychology, human engineering, structural engineering, architectural physics, architectural materials and so on and also is concerned with furniture display, decorative materials, structures, functions, arts and crafts, greening, gardening, etc., and apply to many subjects knowledge to comprehensively conducts multi - levels parietal environment design. its means is to apply to plane part, spatial structure, perspective, illusion, light technology, reflection and color variety principles and material means making " big " space turn to " small ", while " small " space turn to " big ". and according to design requirements, the spaces are re - divided and composed making it increase visual extension, and add layers through various kinds of material structure changes that make " spacious " is not " blank " while " small " is not " crowded ", creating an anticipant style and atmosphere
建築設計是一門復雜的綜合學科，我們研究的目標及內容它涉及到建築學、社會學、民俗學、心理學、人體工程學、結構工程學、建築物理學以及建築材料學等學科，也涉及到傢具陳設，裝潢材料的結構和性能、工藝美術、綠化、造園藝術等領域，而且是運用多學科的知識，綜合的進行多層次的空間環境設計，其在手法上是利用平面主體和空間構造、透視，錯覺、光影、反射和色彩變化等原理以及物質手段，使大空間變小，小空間變大，按設計構思的要求，將空間重新劃分和組合，使之增加視覺上的擴展延伸，通過各種物質構件組織變化，加添層次，以求大而不感其空，小而不感其塞，創造出預期的格調和建築環境氣氛。Abstract : based on the ahievement of epitaxial growth in several perovskite oxide films, we discuss the importance of substrate temperature ( ts ) and substrate material in the epitaxial growth of perovskite oxide thin films. influences of ts on growth orientation and epitaxial threshold temperature were observed. the results indicate that during the growth of the oxide films the phase formation and growth dynamics should be taken into consideration. the threshold temperature for epitaxial growth depends on the substrate materials. this demonstrates the influence of substrate material on the initial nucleation and epitaxial growth
文摘:在成功地外延生長超導、鐵電、鐵磁等多種性質的鈣鈦礦結構氧化物薄膜的基礎上，討論影響氧化物薄膜外延生長的一些因素.考慮到相形成和薄膜生長動力學，在利用脈沖激光淀積法外延生長氧化物薄膜中襯底溫度是十分重要的工藝參數.襯底溫度對成相和生長薄膜的取向都有影響.考慮到薄膜是首先在襯底表面成核、成相併生長.因此襯底材料晶格的影響是不容忽視的.觀察到襯底材料對薄膜外延生長溫度的影響.在適當的工藝條件下，利用低溫三步法工藝制備得到有很強織構的外延薄膜.這突出表明界面層的相互作用對鈣鈦礦結構薄膜的取向有著相當大的影響The development of polymeric photoelectron apparatus is introduced first, and then the author summarizes the status quo of polymeric optical delay - line, expounds the material characteristic and designs the structure of the delay - line
本文首先介紹了有機聚合物光電子器件的發展，總結了有機聚合物光波導延遲線的研究現狀，接著闡述了聚合物材料的性能並對延遲線的結構進行了設計。Common test methods for insulating and sheathing materials of electric cables. part 2 : methods specific to elastomeric compounds. section one : ozone resistance test - hot set test - mineral oil immersion test
電纜絕緣和護套材料通用試驗方法第2部分:彈性體混合料專用試驗方法第1節:耐臭氧試驗-熱延伸試驗-浸礦物油試驗Professor cheng has received numerous awards for his outstanding work in research. his research interests include orthopaedic surgery, paediatric orthopaedics, etiology and etiopathogenesis of adolescent idiopathic scoliosis, congenital muscular torticollis, and biomaterial basic science and applied studies
他的主要研究范疇包括骨科外科、小兒骨科、青少年特發性脊柱側彎、先天性肌性斜頸、肢體延長的應用及骨密度研究、生物材料的基礎研究及應用等。With adsorption and ion exchangeability, it is mainly used as additive in feed, it can absorb ammonia, fix nitrogen, delay the time nutriments stay in alimentary canal, absorb detrimental substance, improve the function of digest, supply many microelements and macroelemnts for livestocks
主要用作飼料的添加劑，具有吸附性和離子交換性，能吸氨固氮延緩營養物質通過消化道的時間吸附腸道有害物質，改善消化機能同時可以供給畜禽多種微量和常量元素，促進增產增重，提高飼料報酬。Compared with steel structure, preflex composite structure has the advantages of not only saving steel but also being able to strengthen rigidity of structure members and the whole structure. in addition it has better characteristics in fireproof and antirust. compared with reinforced concrete structure, it has a lighter structure weight, higher strength, higher bearing capacity and better ductility as well
與鋼結構相比，它不但節省鋼材，而且能夠增強構件及建築物的剛度，防火和防銹性能好；與鋼筋混凝土結構相比，它不但重量較輕，而且具有較高的強度、承載力和良好的延性，能充分發揮鋼和混凝土兩種不同材料的受拉受壓特性。Spacecrafts are working in the space environment, which is full of sorts of physical mediums. and these mediums will impact on the altitude movement of spacecraft. spacecraft attitude control during propulsive maneuvers is complicated due to several factors as listed below : ( i ) nonlinear dynamics with time delays, ( ii ) modeling and parameter uncertainties, ( iii ) flexible modes due to fuel sloshing and appendages, ( vi ) constraints on propulsive force and torque inputs, ( v ) constraints on acceptable angular rates and attitude, ( iv ) autonomous reconfiguration requirements under failure conditions
飛行器是在一定的空間環境中飛行，而空間環境中充滿著各種物理介質，對飛行器的姿態運動產生不同程度的影響，所以空間飛行器的姿態控制相當復雜，它受到如下因素的制約： （ ? ）帶時延的非線性動態特性（ ? ）模型和參數的不確定性（ ? ）燃料的激蕩性以及燃料消耗所引起飛行器的質量變化（ ? ）推力和輸入力矩的約束性（ ? ）額定角速度約束和姿態約束（ ? ）在故障發生的情況下自動重新配置的必要性。Acceptance check and reception systems of plant
限制溢出物蔓延的吸收性材料分享友人