弧度測定 的英文怎麼說
中文拼音 [húdùcèdìng]
弧度測定
英文
circular measurement- 弧 : 名詞1. [數學] (圓周的任意一段) arc2. (古代指弓) bow
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 測 : 動詞1. (測量) survey; fathom; measure 2. (測度; 推測) conjecture; infer
- 定 : Ⅰ形容詞1 (平靜; 穩定) calm; stable 2 (已經確定的; 不改變的) fixed; settled; established Ⅱ動詞...
- 弧度 : 1. [數學] (量角單位) radian2. (弧度法) circular measure; radian measure弧度測量 arc measurement
- 測定 : determine; determination; setting-out; admeasurement; assignment; assay; finding
-
Determination of colour fastness of leather to light : xenon lamp
皮革耐光照色牢度的測定.氙弧燈After an introduction to the research on the software for the design of the variant steel arched girder construction, the creation of the structural model, the structure of the supporting seat, the design of the variant arched girder, and the measures taken to ensure the stability of the plane surface of the arched girder, the thesis goes to study the methods for the hoisting and the angle setting of the long - span arched girders, as well as the bolting of the axle pin in the hinge support
論文首先對變異鋼拱架結構設計可採用的軟體、結構模型的建立、支座構造形式、變異拱梁的設計,以及保證拱梁平面外穩定所採取的措施等進行了研究,然後研究了大跨度變異鋼拱架弧形梁吊裝、角度的調整、鉸支座穿軸銷等的施工方法,最後對施工完成後的位移進行了實際量測。Abstract : the image of arc zone of flux - cored underwater wet welding was developed with underwater ccd camera system and composed filter technology. the discussion is mainly focused on the theory of edge detection. an image edge detection method based on median filter and grads algorithm was developed to detect the arc burning zone and arc bubble zone efficiently, which laid the foundation for further analysis of underwater wet welding arc mechanism and process control
文摘:通過復合濾光技術和水下ccd攝像系統,採集出了藥芯焊絲水下濕法焊接電弧區域圖像,重點論述了邊緣檢測理論,確定了基於中值濾波和梯度運算元的電弧區域圖像邊緣檢測方法,有效地區分了電弧燃燒區域和電弧氣泡區域,從而為水下濕法焊接電弧的機理分析及水下焊接過程式控制制奠定了基礎。Quantitatively : reciprocal of the value ( generally in minutes of arc ) of the angular separation of two neighboring objects ( points or lines ) which the eye can just perceive as being separate
定量方面:任一空間分辨力的測定結果,例如觀測者恰可察覺分離的兩個相鄰物體(點或線或其他特定刺激)的用弧分表示的角度間隔的倒數。The whole software is composed of four modules :, the scaling module, the hangingjgear, the process module. the three modules are independent, moreover they are interrelated, which make then arc - gear - capp is a whole process
各個模塊既是獨立的,可以單獨調用其中的任何一個模塊;又是相互聯系的,構成一個整體,從而實現工藝規程的制定、機床掛輪的選擇、尺寸測量、精度與公差的選擇等完整的圓弧齒輪的加工過程。Design and experiment of spiral bevel gears with high contact ratio
高重合度弧齒錐齒輪加工參數設計與重合度測定And line grating is used to measure arc length in order to increase angle measuring precision, thus high differentiate locating in space can be realized
用長光柵測弧長來實現角度測量的高解析度要求,實現空間上的高精度定位。The two - dimensional axisymmetric subsonic - transonic - supersonic flow in an experimental arcjet thruster is simulated numerically using flux vector splitting method. the profiles of density, velocity, temperature, pressure and mach number can be obtained by the computation. the computation grid and some computed results are given here. the test equipment such as power supply system, ignition system, propellant supply system, arcjet thruster, thrust measuring device and vacuum system are introduced briefly. some working phenomena of the arcjet are observed and discussed. three different kinds of instability appeared in the process of the experiments. except some important parameters are measured, it is found that the operating stability of argon is better than that of nitrogen
對一實驗電弧加熱式發動機二維軸對稱亞跨超音速流動進行了數值模擬,所採用的方法是矢通量分裂演算法.通過計算可以得出密度、速度、溫度、壓力和馬赫數的分佈.給出了計算所使用的網格和一些計算結果.簡要介紹了實驗所使用的設備,如電源系統、點火系統、推進劑供給系統、電弧加熱式發動機、推力測量裝置和真空系統.對所觀察到的一些工作現象進行了討論.有三種不同的不穩定性出現于實驗過程.除了所測量的一些重要參數,通過實驗發現氬比氮工作更穩定Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - part 3 : determination of ozone concentration using fixed point measurements
焊接和相關工藝的衛生和安全.電弧焊產生的煙塵和氣體取樣的試驗室方法.第3部分:用固定點測量法測定臭氧濃度Microplate luminometry for toxicity bioassay of environmental pollutant on a new type of fresh water luminescent bacterium vibrio - qinghaiensis sp. - q
測定環境污染物對青海弧菌發光強度抑制的微板發光法研究The starting point of the arc is determined by measuring clockwise from the x - axis of the ellipse at the 0 - degree angle by the number of degrees in the start angle
弧線起始點的確定方法是:從橢圓x軸( 0度角)開始順時針測量起始角度的度數。分享友人