弧形槽 的英文怎麼說

中文拼音 [húxíngcáo]
弧形槽 英文
arc chute
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 弧形 : arc; curve弧形避雷器 arc-arrester; 弧形槽 arc wall; 弧形構造 arc structure; 弧形閘門 [水文] radial gate
  1. Arcwall coal cutter

    弧形截槽截煤機
  2. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  3. 45taper concave slope of chassiss main body elastic material output bar of case shell s main body 30strip arcual fillister of chassiss main body

    底盤主體45錐形凹坡外殼主體配置彈性導料條底盤主體長條30弧形凹槽。
  4. From up to down, food firstly arrives at material output bar, then lays off from taper concave slope, finally, food gets into round basin on baseplate after mutual effect through arcual fillister

    食品從上而下先到達彈性導料條，再到錐形凹坡下料，最後通過弧形凹槽的相互作用，食品到達底盤上圓形食盆。
  5. This paper puts out the edge shapes curvilinear equations, of the edge shapes of double circular gear hob, and analyzes the tooth surfaces characterist. it also points out that the gear hob is a kind of approximate shape building cutting too ls in the whole course of using

    本文提出了直槽雙圓弧齒輪滾刀刃形曲線方程式，並進一步分析了該滾刀的齒面特性，指出該滾刀從整個使用過程看，是一種近似造型的刀具。
  6. Abstract : this paper puts out the edge shapes curvilinear equations, of the edge shapes of double circular gear hob, and analyzes the tooth surface ' s characterist. it also points out that the gear hob is a kind of approximate shape building cutting too ls in the whole course of using

    文摘:本文提出了直槽雙圓弧齒輪滾刀刃形曲線方程式，並進一步分析了該滾刀的齒面特性，指出該滾刀從整個使用過程看，是一種近似造型的刀具。
  7. Abstract : a new waveguide which can change the wide wall of a rectangular waveguide into a symmetric arc wall is named as a cam - rectangular waveguide. comparing to sectoral waveguide, the new waveguide has the same voltage characteristics and is easier to be produced and fixed. an approximate formula of the dominant mode fields and the normalized conductance of a longitudinal resonant slot cut in the curved wall of a cam - rectangular waveguide are given. a resonant slot linear array in c & x band is designed, in which the slot voltage distribution is equiphase and the input is matched. the input voltage stationary ware ratio and the h - plane pattern of the antenna are measured. the experimental results show the conformance with theoretical results

    文摘:把常用的矩形波導一個寬面改成圓弧形構成的波導稱為圓突-矩形波導.這種波導與扇面波導相比：電性能相當；波導管結構更加簡單，容易加工，便於安裝.文中給出圓突-矩形波導中主模場，圓曲面上縱向槽歸一化諧振電導近似公式.設計了c和x波段波導曲面縱向諧振縫隙線陣，縫隙電壓相位為同相分佈，輸入端匹配.實際測量了天線輸入端電壓駐波比和h面方向圖，理論與實驗相吻合
  8. Iour company have designing and processing of ability and we can manufacture the various kinds melted - zinc - bath of specifications and shapes, and we also can produce the machine equipment, for example, there are a lot of stamping dies and stretching dies ect.,

    一根據用戶要求可製作各種規格形狀的鍍鋅鍋槽，備有全套沖壓和拉伸模具等加工設備，有先進的焊接水平，採用電弧氣刨來保證焊縫質量。
  9. By comparing between the rectangular groove and curved groove, we find that two high stress area of rectangular groove o - ring occurs during the sealing period, and the wearing on the both inside and outside diameter surfaces ; the high stress area only happens at the part area of cone shaft, and the distribution of stress is more even than the former, and the wearing is on the inside diameter surface, the improvement of its distortions makes the service life of sealing lengthen

    通過矩形槽和弧形槽的對比研究發現，矩形槽o形圈在密封過程中出現兩個高應力區，磨損發生在內徑、外徑兩個表面_匕，弧形槽o形圈的高應力區僅出現在牙爪軸鄰近的局部區域內，應力分佈較前者更為均勻，磨損進發生在內徑表面，其受力變形狀況的改善將使密封壽命進一步提高。
  10. Gear form is precisely, plotted by portray point. for friendly user interface, the dialog - box is given, using dcl language to compile dialog box program. because the given program can not only output all the optimum basic parameters of pump gear, but also simulate the meshing process of a pair of pump gears, gear pump can be designed and manufactured economically

    精確繪出泵齒輪的輪齒幾何形狀，尤其精確繪制出了標準齒輪滾刀切出的齒根過渡曲線，演示了國標雙圓弧頭標準滾刀加工泵齒輪的過程，並實現了泵齒輪副的嚙合模擬，這些對檢查輪齒干涉以及確定齒輪泵的卸荷槽位置和形狀提供了依據。
  11. Therefore, the common rectangular groove seals are often be changed into the curved groove with some arc degree. when the o - ring acted as sealing function is placed in the curve groove with suitable design, its stress, strain and friction are all improved so as to lengthen the service life of sealing. the finite element method has guide meaning to analyze and design of structure

    為此，普通矩形槽密封被嘗試著改為具有一定弧度的弧形槽，當徑向密封作用的o形圈被置於設計合理的弧形槽內，其受力、變形和摩擦狀況均得到改善，有助於密封壽命的提;銳有限元法對結構的分析和設計具有指導意義。
分享友人
分享到 Line

分享到臉書