弧矢一 的英文怎麼說
中文拼音 [húshǐyī]
弧矢一
英文
wezen wezea-
Research about ctod and its components 8 ", " shows that the direction angle of ctod vector is identical with the fracture angle of void - mode fracture, which is obtained through experiments, and it is also identical with the result got by peak value line of stress triaxiality. besides, 8 i " was compare with vgc as criterion for initiation of void - mode fracture
對裂紋尖端張開位移ctod及其張開型分量~ 1和剪切型分量~ 11的分析表明，在試件發生韌窩型斷裂時，按照圓弧裂紋中ctod矢量的垂直方向預測的斷裂角與試驗測得的斷裂角符合較好，與三軸度脊線預計的結果也比較一致。The mathematic model of the ultra - thin spherical mirror is to be treated as elastic thin shell. then the predigested model, i. e., bended beam, used in qualitative analysis was proposed, and its deflection and stress formulas under the freely supported condition were set up. based on an off - axis aspherical primary mirror, the relationship of aspherical surface error ( rms ) in tangential plane with bended beam ’ s radius r, position s of concentrated load p and geometry length l of arc was analyzed
根據這一設想，本文建立了超薄鏡的數學模型?薄殼，並提出了強制力作用下超薄鏡的簡化模型?曲梁，推導了曲梁在簡支情況下受力變形的撓度公式，並結合一個實例，計算出曲梁變形后與所需非球面的面形殘差（ rms ）在子午方向與曲梁弧長l 、曲梁半徑r及集中力位置s的關系及滿足面形精度的r和s范圍，分析了弧矢方向的rms ，得出了同時滿足子午和弧矢方向面形要求的l 、 r和p 。Firstly, a simple and practical representing method of the tooth edge tangential vector is applied to replace the traditional differential formula, the simple solving technique of edge contact problem makes the geometric edge contact analysis of the complex curve surface realize. secondly, using numerical searching and mathematical programming method solves the contact directions and loaded contact problem. finally, whole numerical simulation method is provided for loaded tooth contact analysis of high contact ratio spiral bevel gears
首先以一種簡單實用的輪齒邊緣切矢量的數學表示方法取代了經典的微分表達式，大大簡化了幾何邊緣接觸的求解，使復雜曲面的幾何邊緣接觸分析得以實現；其次又採用數值搜索與數學規劃法求解了邊緣接觸的主方向和承載接觸問題，為高重合度弧齒錐齒輪承載嚙合全過程的數值模擬提供了完整的方法。The two - dimensional axisymmetric subsonic - transonic - supersonic flow in an experimental arcjet thruster is simulated numerically using flux vector splitting method. the profiles of density, velocity, temperature, pressure and mach number can be obtained by the computation. the computation grid and some computed results are given here. the test equipment such as power supply system, ignition system, propellant supply system, arcjet thruster, thrust measuring device and vacuum system are introduced briefly. some working phenomena of the arcjet are observed and discussed. three different kinds of instability appeared in the process of the experiments. except some important parameters are measured, it is found that the operating stability of argon is better than that of nitrogen
對一實驗電弧加熱式發動機二維軸對稱亞跨超音速流動進行了數值模擬，所採用的方法是矢通量分裂演算法.通過計算可以得出密度、速度、溫度、壓力和馬赫數的分佈.給出了計算所使用的網格和一些計算結果.簡要介紹了實驗所使用的設備，如電源系統、點火系統、推進劑供給系統、電弧加熱式發動機、推力測量裝置和真空系統.對所觀察到的一些工作現象進行了討論.有三種不同的不穩定性出現于實驗過程.除了所測量的一些重要參數，通過實驗發現氬比氮工作更穩定The two - dimensional axisymmetric subsonic - transonic - supersonic flow in an experimental arcjet thruster is simulated numerically using flux vector splitting method
摘要對一實驗電弧加熱式發動機二維軸對稱亞跨超音速流動進行了數值模擬，所採用的方法是矢通量分裂演算法。分享友人