彈藥分發 的英文怎麼說

中文拼音 [dànyàofēnfā]
彈藥分發 英文
ammunition distribution
  • 彈 : 彈名詞1. （彈子; 小球形的東西） ball; pellet 2. （內裝爆炸物, 具有破壞和殺傷能力的東西） bullet; bomb
  • 藥 : Ⅰ名詞1 （藥物） medicine; drug; remedy 2 （某些有化學作用的物質） certain chemicals Ⅱ動詞1 [書面...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 發 : 名詞（頭發） hair
  • 彈藥 : ammunition; cartridge; ammo彈藥材料 ammunition material; 彈藥艙 ammunition cabins; 彈藥車 artille...
  1. Abstract : through analysis, an approach is taken to use 100mm gun rack instead of 105mm, based upon energy - conversion and function mechanism, to satisfy the production and research of the product

    文摘:從能量轉換及作功原理入手，分析並提出了100滑炮架取代105炮架應採取的措施，滿足了迫擊炮彈發射裝藥生產和科研試驗使用要求。
  2. In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys

    本文首先對子母式穿甲彈總體參量作了全面的計算分析，其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度，論證了子母式穿甲彈對付爆炸式反應裝甲的可行性，然後對子母式穿甲彈彈頭部進行了總體設計，其中主要對子彈的發射過程進行了詳細的分析，得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系，設計出了合理的母彈彈頭部結構和子彈的結構，並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。
  3. German pz. kpfw iv ausf f fahrgestell a total of 13 munitionsschlepper were produced on pz. kpfw. iv ausf. d, e, and f chassis which had been acquired from the normal pz. kpfw. iv production run as reported in may 1941. there were two munitionsschlepper for each of the six geract 040 nr. i to vi and one for the experimental geract nr. vii

    為配合已經生產的「卡爾」臼炮， 1941年5月德國兵器局從生產線上抽取部分的pz . kpfw . iv ausf . d ， e ， and f型坦克底盤改裝為彈藥車，每輛備彈4發，車體後部有一個可敞開的彈艙。
  4. Actually, it ' s significant of area measurement on curved surface in production and research. for example, the area measurement of cartridge surface ablation is an important means to analyze the quality and shoot of cannon

    實際上在生產、科研中對曲面面積的測量有著重要的意義，如火炮藥筒燒蝕面積的測量，它是分析炮彈的質量和發射狀況的一個重要手段。
  5. Abstract : aimed at the accident of chatching fire of a certain type of self - propelled antitank gun s chamber, the paper analyses the normal burning of powder and the efficiency of the gun s extracting device and other factors affecting the burning velocity, makes an improvement on the weapon system, and puts forward the requirements for using the gun under army conditions

    文摘:針對某型自行火炮實彈射擊中戰斗室彈藥倉內半可燃藥筒起火燃燒事故，通過對可燃藥筒完全燃燒的理論分析和火炮抽氣裝置結構效率分析以及可能影響藥筒燃燒速度的其他因素分析，提出武器系統及可燃藥筒改進意見，並對部隊條件下的使用提出了要求，對改善裝備性能，預防事故發生具有重要意義。
  6. Firstly according to the shooting process of the ahead system, and on the basis of the ammunition makeup, the movement of the damage element is analysed, the practical character of damage field is given. then the critical components corresponding to the damage levels are chosen, and dynamic impact process between the damage field and the target is studied deeply. finally, in accordance with the logic relation of the components damage and the target damage, the whole target damage effect is calculated

    首先從ahead彈的射擊作戰原理出發，以彈藥結構為基本依據，分析毀傷元的運動特性，得到毀傷場的具體特徵，然後，對目標進行與毀傷級別對應的要害部件的提取，進而，對毀傷場與目標動態交匯過程進行了深入分析，最後，根據部件毀傷與目標毀傷的邏輯關系得到整個目標的毀傷概率。
  7. 5. the internal ballistics and the throttling performance of 85 % h2o2 - pe hybrid rocket motor loaded with tube grain are studied. the hot firing data of two test motors have been carefully analyzed

    研究了管型藥柱的85 h _ 2o _ 2 - pe固液火箭發動機的內彈道性能和節流特性，分析了兩臺發動機的試驗結果。
  8. This thesis presents basic researches on spraying and atomization process of the liquid propellant - key issue of regenerative liquid propellant gun interior ballistic process. the distributing properties of droplet sizes in atomization field of liquid propellant hy911 were experimentally, theoretically and numerically investigated

    本文以再生式液體發射藥火炮（ rlpg ）為工程背景，圍繞rlpg內彈道循環的關鍵問題?液體藥噴射及霧化過程開展基礎研究，針對國產hy911液體發射藥，系統地進行了噴霧場液滴尺寸分佈的測試、理論建模與數值模擬。
  9. The mathematical model of released heat from propellant in boxed ammunition is etablished, the residualenergy of propellant in ammunition during storage is calculated numerically, and the results of calculation areanalyzed and discussed

    首先建立了箱裝彈藥中發射藥放熱規律的數學模型，然後利用數值模擬的方法計算了其在貯存過程中的剩餘能量，最後對計算結果進行了分析與討論。
  10. In fitting out an army, we give each soldier his own knapsack, arms, powder, his blanket, cup, knife, fork and spoon

    要裝備一支軍隊，就要給每個士兵分發背包、武器、彈藥、毛毯、口杯、刀叉及湯匙。
  11. In this paper, based on the viscoelasticity theory and the dynamics theory, the finite element method ( fem ) is used to the structural integrality analysis of the grain in rocket engine of the base - bleed and rocket compound extended range projectile in chamber

    本文基於粘彈性理論和動力學理論，運用ansys對某型號底排?火箭復合增程彈助推火箭發動機藥柱在膛內的結構完整性進行了系統的分析。
  12. Characteris : this article is the herb medicine gastrodiae rhizoma fomulation affinage in the adoption but become, the osmosis element, the all - directions own protects the wet, the guilder toughness, betterment hair guilder, anticipate to shed off and the ultraviolet ray damages, insulate the harmful component, the brightness is meek and build function

    ：本品是採用中草藥一天麻配方精煉而成，能有效促進血液循環，添加保溫因子，滲透元素，全方位擁有保溫、彈性、修復、活化毛發細胞、增強發質韌性，改善發質、防止脫落及紫外線傷害、隔離有害成分、光澤柔順及造型功能。
  13. The main work and achievements are summarized as follows : based on herrmann variational principle and the nearly - incompressible viscoelastic constitutive relation, a new type of viscoelastic incremental finite element method is presented. in this method, incremental arithmetic is applied to solving the hereditary integrals. it needs less memory space, has simple parameter matrix, and calculates stiffness matrix only once

    主要研究內容如下：從herrmann變分原理出發，基於適用於近似不可壓縮材料的粘彈性本構關系，利用增量法處理遺傳積分，發展了一種粘彈性增量有限元方法，所需存儲空間較少，參數矩陣形式簡單，求解過程只需要形成一次剛度矩陣，適用於藥柱的結構計算，奠定了確定性分析基礎。
  14. In this dissertation, the application of low temperature sensitivity coefficient ( ltsc ) high - energy nitroamine propellant in a 105mm gun has been studied theoretically and experimentally. the ltsc coated propellant ingredient calculation program, the closed vessel and gun experiment data processing program and the ballistic simulation program, which can simulate gun interior ballistic performances based on closed vessel experiment data, have been programmed with visual program design method

    本文對低溫感高能硝胺發射藥在某105mm火炮上的應用進行了理論和實驗研究，編寫了低溫感包覆火藥包覆層組分計算、密閉爆發器和火炮實驗數據處理以及利用密閉爆發器實驗模擬火炮彈道性能等可視化應用程序。
  15. The result shows that the movement of the propellant grains is complex and relative to the ignition system very much. guns with center tube ignition and flame - spreading system can alleviate the accumulation of the propellant effectively, and will have better performance

    結果分析表明：火炮點火後膛內火藥顆粒的運動情況十分復雜，其運動規律與點傳火的方式密切相關，點火孔均勻分佈的中心傳火管點火方式可以有效的改善發射過程中火藥顆粒在彈丸底部堆積的現象，獲得更佳的發射效果。
  16. The characteristic of phased - mission system is discussed with combat task flow of a combat unit as example in this article, and under a certain power guideline, the method of founding the ammo equipping model form the point of view of the system ' s reliability and availability in phased - mission combat task flow is analyzed

    以某作戰單元的一次作戰任務流程為例，詳細地討論了多階段復雜任務系統的特點，並從基本任務階段的系統可信性、可用度的角度出發，分析了在滿足給定火力指標的前提下，建立整個復雜作戰任務流程中彈藥配備模型的方法。
  17. The analysis is focused on the acceleration influence on burn rate of the grain when the solid rocket motor is working under lateral overload. the simple model of burn rate in acceleration field is established. moving laws of burn surface for two different grain type srms are respectively derived, on the base of which zero dimension and one dimension quasi - steady internal ballistic simulation models are established

    分析了橫向過載對固體推進劑燃速的影響，建立了橫向加速度場中的簡化燃速模型，推導了兩種不同藥型的燃面退移規律，在此基礎上進行了零維、一維準定常內彈道計算與分析，建立了固體火箭發動機內流場三維兩相流模型。
  18. ? by comparing the experimental data with the modeling results, it was found that the he in the projectile produces reaction after considerably long time. and the expansion velocity of the shell is about one hundred meters per second, far below the velocity driven by detonation ( about 2000m / s ). ? the post - test recovered fragments prove that the reaction violence remains on low level

    ?通過試驗結果和數值模擬的殼體邊界和徑向膨脹速度的對比分析，發現帶炸藥彈體在以120m s左右的速度撞擊鋼靶后，經歷了相當長時間后才產生反應，且此時殼體的膨脹速度僅在百米每秒的水平，遠低於爆轟驅動下能達到2000m s左右的速度。
分享友人
分享到 Line

分享到臉書