徑向收縮 的英文怎麼說

中文拼音 [jìngxiàngshōusuō]
徑向收縮 英文
radial shrinkage
  • : Ⅰ名詞1 (狹窄的道路; 小路) footpath; path; track 2 (達到目的的方法) way; means 3 (直徑的簡稱...
  • : Ⅰ動詞1 (把攤開的或分散的事物聚集、合攏) put away; take in 2 (收取) collect 3 (收割) harvest...
  • : 縮構詞成分。
  • 收縮 : 1 (由大變小; 由長變短) contract; shrink 2 (緊縮) concentrate one s forces; draw back 3 take u...
  1. Rail corrugation at high frequency wheel rail interaction

    小口軸對稱噴嘴射流沖擊大平板噪聲指特性研究
  2. With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress

    研究結果表明:殼體筒段受軸拉伸和內壓載荷作用時,軸和環載荷的比率不同,母層和子層可能發生拉伸屈曲,也可能發生屈曲,或者同時發生拉伸和壓屈曲;母層與子層各異性存在差異,即泊松比與剪切模量不匹配時,將使子層板的邊界上承受壓和剪切作用,當分層達到臨界狀態則發生屈曲,當母層與子層的各異性差異越大,則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半等因素有關。
  3. Secondly author calculates and analyses normal stress and shear stress of the girder for a assembling post - tensioned concrete skew girder bridge with a span of 40 m due to the actions of the dead load, temperature changes, shrinkage and creep of concrete and live loads, and calculates and analyses normal stress and shear stress of diaphragms due to the actions of the subordinate phase dead load, temperature changes, shrinkage and creep of concrete and live loads

    其次重點對跨為40m標準設計的裝配式后張預應力混凝土斜梁橋在恆載、溫度變化、混凝土和徐變、活載作用下主梁的正應力、豎變形和恆載、活載作用下主梁的剪應力進行計算分析。計算分析橫隔板在二期恆載、溫度變化、混凝土、活載作用下的正應力、剪應力。
  4. In the process of preparing glass / mullite composite material, research on shrink rate, bending strength, dielectric constant, dielectric loss tangent, etc have been carried out. in the experiment, the thermal expand coefficient of samples is tested, and through sem, insides structure of sintered sample is studied, so the relationship of

    在制備玻璃/莫來石復合材料的過程中,我們研究了燒成后徑向收縮率、試樣的抗彎強度、介電常數、介質損耗及其影響因素,並測試了試樣的熱膨脹系數,通過sem觀測燒成試樣的內部結構情況,找出性能和結構之間的關系。
分享友人