恆行轉速 的英文怎麼說

中文拼音 [hénghángzhuǎnsù]
恆行轉速 英文
konstantfahrdrehzahl constant driving rpm
  • 恆 : Ⅰ形容詞1 （永久; 持久） permanent; lasting 2 （平常; 經常） usual; common; constant Ⅱ名詞1 （恆心...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 轉 : 轉構詞成分。
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 轉速 : speed; revolution; rotation rate; speed of revolution; rotating speed; rotational speed轉速指示器...
  1. Then following reality constituent of engine and connecting component interface, a nonlinear signal cylinder engine model has been created, though fire interval and fire order, a control - oriented four cylinders engine is build. following dynamometer is seen as load, performance of engine is simulated and researched under the condition of constant torque and speed, validation of the math and simulation model have been confirmed by comparison result between simulation with test result of engine performance simulation software dyno

    按照發動機的實際組成，根據各部件的介面類型連接模型庫中的部件，建立了單缸發動機非線性模型，在此基礎上，依據發動機實際發火間隔和順序，建立了面向控制的四缸汽油機模型，並以測功器為負載，通過恆轉矩和恆轉速方式進行了發動機性能模擬和研究，模擬結果和發動機動力性能模擬軟體dyno測試結果的對比驗證了數學模型和模擬模型的正確性。
  2. The effect of cutting speed, cutting thickness, cutting knife and materials on the working power capacity is discussed. finally tractive property of road plane milling machine is also studied. through the comparison of the results of theory calculation and experimental results the equation of working power capacity of milling machine is modified

    本文對冷式瀝青路面銑刨機的動力學工作過程進行了理論分析與試驗研究，並利用金屬材料切削的基本原理，研究了主切削力，並從能量轉化守恆的角度推導了銑刨機銑刨作業阻力和功率計算公式，討論了機器切削速度、銑刨厚度以及刀具與材料特性對銑刨作業阻力和功率的影響規律，最後討論了銑刨機牽引性能，且通過試驗研究驗證了銑刨作業阻力和功率公式。
  3. The traditional refrigeration system in containers adopts the mode of invariable revolution, and its system design is based on what can match the biggest heat load. so the refrigeration compressors and cooling fan motors have been chosen according to their biggest cool and heat burthen in working conditions

    傳統的冷藏集裝箱製冷系統一般採用恆定轉速運行方式，在設計系統時，以能夠滿足最大熱負荷為依據，製冷壓縮機和冷風機選型的根據是最大冷、熱負荷工況。
  4. A mathematic model of the motor is builded and emulated through matlab. the low - speed and constant - torque, high - speed and constant - power state is analyzed and researched, also the software approach of simulation to the driver has been done, a digital signal processor tms320lf2407 is developed successfully to control the perm square - wave bldcm driving airscrew of solar powered unmanned engine. it is useful to the further study

    在matlab下建立了電機的數學模型，通過計算機模擬，驗證了數學模型的正確性，同時在理論上對低速恆轉矩高速恆功率運行進行了分析與研究，提出了一種用模糊控制的方法實現恆功率控制，並對驅動器進行了系統模擬，成功的研製了以數字信號處理控制器tms320lf2407為控制核心的驅動器，控制無刷直流電動機驅動太陽能無人飛機的螺旋槳，為後面繼續研究工作提供了參考。
  5. In addition, in order to make the pumps realize constant injection pressure, the expert tuning pid vfvs constant injection pressure control sub - system for pumps is established and relevant software module is developed. the sub - system can control automatically the quantity and rotate speed of the pumps running to realize the pumps optimum run according to the seawater injection plan of the oil field, which realizes constant injection pressure, energy saving and decreases the consumption to a large degree

    此外，為平臺注水泵機組的優化運行構建了基於專家整定pid控制的變頻調速恆壓注水控制子系統，並開發了相應的軟體模塊，完全省卻了pid控制器的硬體設備，使得注水泵機組可以根據油田注水量的配注方案優化運行，自動控制注水泵的轉速和運轉臺數，既能實現平穩增壓注水，又能在很大程度上節能降耗。
  6. This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

    本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。
  7. Abstract : the responses of shaft bow and their relationships with unbalanceresponses and mechanical or electronic run out are analyzed based on the theory of rotor dynamics. the responses of shaft bow are separated from the unbalance responses successfully by making use of vibration information under different rotor runs. an identification method of thermal bend is presented based on the 2d - holospectrum technique. experimental results show that when bow phase is steady and amplitude is variable, the tangent of initial phase point on the 2d - holospectrum is parallel, which can be effectively used for diagnosis of bent shaft

    文摘:依據轉子動力學理論分析了柔性轉子彎曲響應的特徵，在此基礎上討論了它與不平衡響應及機械與電氣跳動量之間的關系，並利用轉子在不同起車情況下的振動信息，有效地分離了彎曲響應和不平衡響應，求解出彎曲量與不平衡量的比值.提出了轉子在恆定轉速下，基於二維全息譜技術的熱彎曲故障識別方法.研究結果表明，當彎曲量相位穩定而其幅值變化時，轉子響應的二維全息譜初相點的切線是相互平行的，由此可以有效地實現轉子熱彎曲故障的識別與診斷
  8. Secondly, to achieve the independent regulation of active and reactive power output from the generator side which is designed for the purpose of tracing the maximum wind - energy capturing. the paper has analyzed the mathematic model of the ac excited doubly - fed machine and the stator field orientation control strategy of the motor as vscf wind power generator. thirdly, it has put forward and designed the dual pwm converter with the capacity of energy flowing bidirectional aimed at the demand of rotor energy bidirectional flow. the author constructed reliable and integrated experimental system and did a series of experimental study including no - load, cutting - in network and power generation at, below and above the synchronous speed

    論文首先分析了風機運行特性及其最佳風能利用原理，通過模擬及實驗驗證了採用直流電機的輸出特性模擬風力機的最大輸出功率曲線的可行性，並給出了模擬系統的硬體結構；然後為了實現交流勵磁發電機有功、無功功率獨立調節機理，分析了交流勵磁雙饋發電機的數學模型和在追蹤最大風能捕獲變速恆頻風力發電時必需的定子磁鏈定向矢量控制策略；針對雙饋發電機轉子能量雙向流動的要求，提出並設計了具有能量雙向流動能力的雙pwm交流勵磁用變頻器；最後為實現從理論到實踐的全面研究，研製出了一套小功率完整的雙pwm變頻器交流勵磁的雙饋風力發電機實驗系統，進行了空載、並網、同步速及上、下的發電運行等一系列的運行實驗；所完成的模擬和實驗研究均驗證了理論、模型和控制策略的正確性、可行性。
  9. It also builds the mathematic model of all section of vscf ac exited wind power generation system on a - b - b and d - q coordinate system by the coordinate commutation technology. the thesis gives the characteristics of torque, active power, reactive power and the steady - state analysis of it. it proves that the capability of wind generator is determined to slip, the amplitude and phase of rotor voltage, the phase dispatch between stator voltage and rotor voltage

    並分析了交流勵磁風力發電機作變速恆頻運行時的工作原理，闡述了與同步發電機、異步發電機的不同之處，分析了其能量平衡關系，在坐標變換技術的幫助下，詳細推導了交流勵磁發電機在a - b - c坐標系和d - q坐標系下的數學模型，分析並模擬了其有功和無功特性、轉矩和功率調節特性、穩態運行和機械特性，證明了發電機的性能由轉差率、轉子電壓的相位和幅值、定轉子電壓相位差所決定的。
  10. In the dissertation, a novel hybrid excitation constant voltage synchronous generator is adopted to improve the system performance, which takes the advantages of both electrical excitation and permanent magnet machines. a parted configuration is presented in order to design the structure of the generator. the adaptive digital adjustment is settled in principle using the single chip microcomputer 80c31 as the control core of the voltage regulator and adopting the proportion - integral - differential control as the control arithmetic, then a sample is made

    論文對同步發電機的工作原理、性能特點、電機本體以及電壓調節器的硬體和軟體設計進行了研究，針對稀土永磁同步發電機變載、變轉速情況下輸出電壓不可調的不足之處，採用一種新穎的電機型式? ?自適應復合勵磁恆壓同步發電機，綜合了永磁發電機和電勵磁發電機的優點，提出一種磁路分開的結構進行電機本體的設計，並選用單片機80c31作為電壓調節器的控制核心，比例?積分?微分控制（ pid ）作為其控制演算法，從原理上較好地解決了其電壓的自動數字調節，並試制了一臺樣機。
  11. The gpd3402 inverter and plc being selected to set up open - loop and closed - loop speed regulation systems, applying the invariable v / f control, sensorless vector control, slip compensation, process pi and network control technologies control the hoist motor of the stacker crane

    本文基於gpd3402變頻器的變頻調速方式進行應用開發，對堆跺機提升電機採用變頻調速控制，採用gpd3402變頻器及plc ，組建開環調速系統，分別應用恆壓頻比、無速度傳感器、矢量控制、轉差補償控制技術。
  12. The polar coordinates of tool swinging pivot are figured out, and the expressions of tool swinging and the variable - speed of spindle are derived

    通過對凸輪車削的運動關系進行分析計算，推導出在恆角度與恆速度切削的情況下，刀具擺角、機床主軸轉速與凸輪轉角位置的關系，為在實際中應用提供了理論依據。
  13. This paper studies and designs a variable frequency speed regulation system applied to induction motors by means of votating speed difference frequency fuzzy control. the general scheme of the system is presented. circuits and software are designed for the major parts of the system such as constant magnetic linkage control frequency converter and votating speed difference frequency fuzzy controller

    本文對異步電動機轉差頻率模糊控制變頻調速系統進行了較為詳細的研究和設計，給出了系統的總體方案。對于系統的主要組成部分? ?恆磁鏈控制變頻器和轉差頻率模糊控制器進行了設計。
  14. By using for reference, in theory, simply introduced the basic working principle of the secondary adjusting hydrostatic transmission system, the basic controlling rules of secondary regulation, and the most radical controlling rules such as rotational speed, torque control and power control etc. by analyzing theory and studying, check - uping the motion parts of secondary element and constructing the control system ; and setting up the topmost rotational speed control system ; designing and completing the software of date processing and system control

    通過參考相關的資料，從理論上介紹了二次調節靜液傳動系統原理，二次調節系統的基本控制規律，簡要介紹了最基本控制規律如：轉速控制、扭矩控制和恆功率控制等。在理論分析和研究的同時，對二次元件的運動部件的檢測和控制系統進行構建；組建了二次元件最高轉速控制系統；設計並完成了數據採集和系統控制軟體；同時，對二次元件控制系統和制動特性採用pid控制進行計算機模擬研究。
  15. Finally, a large number of experiments are done in this paper, such as the experiments of constant voltage and constant frequency, the current waveform of rotor, different carried - wave ratio, the transition smoothly and connecting electricity web etc. the theoretics and experiments results show that the design of control system is rational, terse and steady ; the analysis of control strategy and system experiments are successful basically

    最後，本文對系統進行了大量的試驗研究。其中主要包括：恆頻恆壓，轉子電流波形，不同載波比，同步速過渡及其並網試驗等。理論及其試驗結果表明：本控制系統的設計是合理、簡潔、穩定的；控制策略的分析和試驗基本上是成功的。
  16. According to the fault of complicated calculation - control, characteristics easily affected by the induction motor ' s parameters and the different result between practical function and theoretical analysis in vector control and the defect of the traditional dtc, i designed a new dtc which uses a three - value regulator to get quickly torque control and adopt the control scheme of invariable magnetic chain to improve the performance of adjusting velocity of the induction motor

    由於矢量控制技術中出現的運算復雜、特性易受感應電動機參數的影響和實際運行結果難于達到理論分析的結果等缺點，以及傳統的直接轉矩控制方法的不足之處，設計了新的直接轉矩控制方案。這種方案是應用三值調節器來獲得快速的轉矩控制，並且採用磁鏈恆定的控制方法以提高異步電動機的調速性能。
  17. Two diesel locomotives realized the parallel - control. we can determine two or one diesel locomotives revoluing by the load. by this way, some fuel can be saved, breakdown rate also can be decreased, resoveled the shorting of electricity fitting and kept railway transportaion running in safety and on time

    同時使機車原操作方式不變，優化了內燃機車的控制，並且在重聯時，雙機能進行故障監測與報警，實現柴油機有擋、分段無級調速控制，柴油機自動運轉，閉環恆速控制，實現了設備資源優化配置。
  18. Based on the experience of regulating frequency according to different valve ' s angle, a reasonable controlling tactic is proposed. when the situation changes to a small degree, electromotor makes fan running at a constant rate ; when the situation changes to the limiting range, the discharge header pressure is automatically adjusted by the rate of fan

    制定合理的控制策略，採用基於閥門開度的變頻調節策略，即工況變化較小的情況下，電機帶動鼓風機恆速運行，通過控制閥門開度自動調節集氣管壓力；當閥門開度到達極限值，還不能達到控制要求時，再通過變頻器改變鼓風機轉速，以自動調節集氣管壓力。
  19. Also ac exited generator have many excellent characteristics, it may improving the stability of electric power system, its rotor speed may adjustable, it have abilities for active and reactive power regulating in self - help ways, it not lose steps even when operated in deep lead phase, so it especially applied in wind electric power plant and pumped - storage hydraulic power plant

    交流勵磁發電機作為發電機運行的風力發電系統，利用變速恆頻技術后可大大提高風能的利用率。交流勵磁發電機可改善電力系統穩定性，轉子轉速可變，具有獨立的有功無功調節能力，可以深度進行運行而不失步，特別適用於風力發電、抽水蓄能電站等場合。
  20. Temperature control system of traditional air - conditioner depends on its sensors to monitor indoor temperature ' s changes and to control the compressor to run at a specified speed

    傳統空調器的溫度控制是通過溫度傳感器感受室內溫度變化，來控制壓縮機的開、停（壓縮機以恆定的轉速運行） 。
分享友人
分享到 Line

分享到臉書