拉線坯 的英文怎麼說
中文拼音 [lāxiànpī]
拉線坯
英文
drawing stock-
First calculation method : doing horizontal projection drawing on drawing piece, k value is introduced by area equation of projection drawing, k value is obtained by area equation, along outline of projection drawing to add k value, that is, outline shape of blank drawing, principle area - equal and shape similar are used. second calculation method : along outline of drawing piece horizontal projection drawing, to do normal line of penetration line for wantonly point of this point, to obtain high of drawing piece on this point normal line, point and point is to form outline shape of blank
計算方法之一為k值法：作拉深件水平投影圖，在該投影圖面積方程中引入k值，利用面積相等原理解方程，求得k值，沿水平投影外沿加上k值，即為毛坯圖的外廓形狀。計算方法之二為拉深線法：沿拉深件水平投影圖外廓，在任意點作該點切線的法線，在該法線上以該點拉深件的高度為量，在法線上取截點。Jiye pcd die blanks for drawing wire can always be trusted ; your dies always get excellent polishing quality, producing wire with flawless surface finish
基業cd聚晶金剛石拉絲模坯擁有非常了的拋光質量，能確保拉線的表面光潔度。On basis of the development of modern control technology and apply of the network technology and locale bus - mastering technology ， the paper analyzes the essential element of slab caster system : casting speed ; expatiates in detail on the network structure and communication protocol of ethernet and profibus - dp ; mainly describes the forms of control system configuration ， the function and features of its software and hardware designs ; also, introduces mainly control function of control system, for example ， sequence control, tracking system and operation and monitor function etc. and analyzed and settled the problems of control system in debugging and producing
根據傳統的控制系統存在的一些不完善的問題，基於現代控制技術的發展、網路技術以及現場總線技術的應用，從多方面考慮，決定控制層採用siemens的s7 - 400plc ，現場採用遠程i / o單元，很好的解決了信號量大而又分散的問題。針對生產工藝和機械設備的控制要求，設計了齊全的操作模式和方式，分析了板坯連鑄系統的基本要素：拉矯速度（澆鑄速度） ；根據控制功能的分配及實現，主要說明了plc控制系統的組織結構形式，系統的軟硬體設計的功能和特點。Wire bar or tube drawing dies - as sintered pellets of hardmetal
線棒和管拉模用硬質合金模坯Wire, bar or tube drawing dies - as sintered pellets of hardmetal
線棒和管拉模用硬質合金模坯The purple sand hand - drag base art breaks the banlance of old hitting base art and dang - base model from song dynasties to now
紫砂手拉坯工藝打破了自宋代起至今的傳統打坯鑲接成形法與模型擋坯、灌漿澆注成型法的一統天下，避免了傳統成型所留下的泥條接頭線與模型接線。Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great
採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。Copper drawing stock for electrical purposes are mainly used for mand facturing round copper wire flatten copper wire and other electrcal couductor
電工用銅線坯主要用於拉制圓銅線、扁銅線和其它電工用銅導體。In this paper, through stress analysis of region about conical and spherical parts during drawing, a calculating formula of maximum tangential compressive stess in unsupported wall region is deduced. and this is condition of causing internal wrinkle. then on the premise to guarantee not breaking workpiece, a critical calculating formula is presented
通過圓筒形及盒形件拉深前後網格變化分析，並確定變形區和非變形區，由此得到不規則盒形件毛坯展開形狀由不變形區和參與變形拉深線組成，並用此方法計算出汽車制動閥安裝板的毛坯形狀和尺寸，在試模時一次即獲得成功，具有一定的實用價值。分享友人