拐角角度 的英文怎麼說

中文拼音 [guǎijiǎojiǎo]
拐角角度 英文
corner angle
  • : Ⅰ名詞1 (走路拄的棍子) crutch; cane; walking stick 2 (說數字時用來代替 「七」) a substitute fo...
  • : 角Ⅰ名詞1 (牛、羊、 鹿等頭上長出的堅硬的東西) horn 2 (古時軍中吹的樂器) bugle; horn 3 (形狀像...
  • : 度動詞[書面語] (推測; 估計) surmise; estimate
  • 角度 : 1. [數學] (角的大小) angle; the degree [size] of angle 2. (看事情的出發點) point of view; angle
  1. For the convenience of calculation, ascending branch was simplified into a direct ratio formula and descending branch was simplified into two straight lines divided by knee point

    從方便計算的上建議上升段採用比例方程表示,下降段簡化為以點分界的兩部分直線。
  2. A value between from 0 through 1 that specifies the amount that the curve bends between points, with 0 being the smallest curve sharpest corner and 1 being the smoothest curve

    介於0到1之間的一個值,它指定曲線在點與點之間彎曲的程, 0表示最小彎曲(最銳) , 1表示最平滑彎曲。
  3. We saw that their development of language and forms of discourse, especially their indirection, permit high development of skills we seldom achieve or honor.

    我們見到他們的語言和講話方式的發展,特別是他們的彎抹使技巧得到高的發揮,這些技巧是我們很少掌握或尊重的。
  4. The earths recent spiritual elevation was clearly reflected in the visitors enlightened responses and ready acceptance of masters teachings. for example, one middle - aged gentleman sat in the viewing area and watched two videos in a row, all the while laughing and truly enjoying masters words. in describing his view of the lectures, he said, master is unbiased

    從來賓的反應和接受師父教理的程中,我們可明顯的見證到人類意識的提升,例如有位中年人,滿臉笑咪咪地連續看了兩卷錄影帶之後,他評論道:師父講話很有道理,而且不會彎抹,誠懇又直接地講出心底的話,每一句都合情合理。
  5. The heat transfer and the restriction circumstance are simulated. the temper ature - time curve and the stress - time curve are obtained. because the later joint - filled slots are restrained strongly, in which the thermal stress is great, especially in the corner, in spite of a little temperature rise, some measures should be taken to prevent them from producing cracks

    利用有限元前處理軟體vizicad建立了「 t 」形后澆帶模型,模擬了后澆帶的「熱環境」和「約束環境」 ,計算得到了后澆帶的應力和溫發展曲線,發現雖然後澆帶的溫升不大,但受到的約束較大,因此產生較大的溫應力,特別是在其處,應採取措施防止裂縫的出現。
  6. After excavation, there are concentration phenomenon of stress at the corner or the shiplock room, and the tension zone lies in half of the middle part as well as the part of the two slopes to the lower part of the upright wall. finally the analysis results are compared with site monitoring data in period of construction as well as the feedback reports, the result of all comes to meet with each other very well

    開挖完成後,在閘室處存在不同程的應力集中現象,中隔墩上部1 2的巖體及南北邊坡至直立墻頂部平臺以下的部分巖體為拉應力區。在兩側邊坡及邊墻的塑性區出現在損傷區和部分卸荷影響區內,中隔墩大部分區域的巖體都進入了塑性狀態,閘室底板處的塑性區基本上與損傷區一致。
  7. It utilizes the computer digital image processing technology. and this system can measure the characteristic parameters automatically and quickly, such as luminous intensity, center of far light, corner of the close light. the advantage is high accuracy, good repetition and automatic measurement

    此系統採用多維精密可調工作臺,並利用計算機數字圖像處理技術,以vc + +編程實現,達到了自動測量出被測校準器的發光強,遠光中心坐標,近光點坐標以及光軸偏等特徵參數的目的。
  8. Steam temperature distribution of revolving heat pipe with corner

    式回轉熱管管內蒸汽溫分佈
  9. Simulation tests show that the machine ' s acceleration and deceleration capability is the key factor to the nc machining efficiency and precision when the turning angle between micro - lines is small, and the error of corner machining is the predominant factor when the turning angle increases to certain degree, and the machine ' s maximum driving moment becomes the decisive factor when the turning angle becomes big

    通過模擬實驗得出:當連續小直線段間較小時,機床加減速性能是影響加工效率和表面精的最主要因素;當增大到一定程時,誤差的限製成為約束速提高的主要矛盾;當較大時,機床的最大驅動力矩起到主要作用。
  10. He drove round the corner at a tremendous speed

    他以驚人的速開車轉過那個
分享友人