指令重算功能 的英文怎麼說

中文拼音 [zhǐlìngzhòngsuàngōngnéng]
指令重算功能 英文
instruction retry facility
  • : 指構詞成分。
  • : 重Ⅰ名詞(重量; 分量) weight Ⅱ動詞(重視) lay [place put] stress on; place value upon; attach im...
  • : Ⅰ動詞1 (計算數目) calculate; reckon; compute; figure 2 (計算進去) include; count 3 (謀劃;計...
  • : 名詞1 (功勞) exploit; merit; meritorious service [deed]: 戰功 military exploits; 立功 render me...
  • : 能名詞(姓氏) a surname
  • 指令 : 1 (指示; 命令) instruct; order; direct2 (上級機關對下級機關的指示) instructions; order; direc...
  1. The approach maintains the simplicity of the original algorithm, and carry out perfect model following. the pseudo - inverse method is concerned with distributing the deflection commands of multiple control surfaces of the aircraft to generate required control responses when the number of independent control surfaces is greater than the number of required independent control responses

    偽逆演法通過改變反饋增益來實現故障系統的控制律構,當一個操縱面發生故障后,可改變控制律新分配控制,利用其它操縱面來實現它的,近代先進飛機多採用此方法來提高飛機的容錯力。
  2. Before the connectting between moden and other equipments, it works at the cammand mode, the cammand that is send to moden is used to set or manipulate the mode, after the connectting between moden and other equipments, it works at connectting mode, at that time, the cammand send from the computer is send to another computer which will pass the moden and telephone line. the moden control cammand is called " at " cammand, all the control manipulation is realized by sending the ascii character to moden, after the moden received the " at " cammand, it firstly judges the cammand, secondly, it analyses and executes the cammand, finnally, it executes a response by sending back a ascii character, during the deseign of below - computer, we introduce in detail the deseign of system hardware and system software, below - computer system hardware and system software, below - computer is made up of microchip collecting and controlling system, which finish the strobe and water level data collection, display and disposal, deal with the communication with the above - computer, the microchip is the centre of data dealing with, the peripheral equipments are made up of data collecttion module, control cammand input module, display module, execute output module, and long - distance communication module

    在moden控制軟體的設計中,詳細敘述了moden正常工作時的幾個要函數:初始化函數、撥號處理函數、應答處理函數、掛機處理函數,設計並調試了四個函數的通信程序,數據機工作時存在兩種模式,命模式與連線模式,命模式是針對設置的模式,連線模式是數據傳輸的模式。當數據機未與其他設備連接時,其處于命模式,這時候下達給數據機的是作為數據機本身設置或操作用的;當數據機已經與其他設備連接時,其處于連線模式,所有在此時由計機送至數據機的信息都將經由電話線傳送到另一部計機上。專門使用於控制數據機的集被稱為「 at集」 ,對moden的所有操作(如撥號、應答、掛機等)都可以通過給moden發送ascii字元串來實現, moden在收到at命后,先對命進行判斷,接著分析和執行命緩沖區中的命,最後以自身的ascii字元對命作出響應。
  3. Measurement and characterization of surface texture is an important aspect of precision metrology. historically this has involved partitioning a profile into different wavelength regimes referred to as roughness, waviness and form followed by numerical quantization. parameters computed are then inspected for tolerance compliance to ensure a part performs its intended function. this approach is satisfactory when the specification has been carefully determined and the process is stable. however, when the manufacturing process is under development or when instability or modifications to the process invalidate specifications, there is a need to study surface finish parameters in relation to functional performance or process measures. in this context, the problem of surface texture classification and recognition are discussed. advanced techniques developed for this purpose along with applications are presented. also, the techniques discussed here will be useful across large bandwidth, from the characterization of nano scale to traditional micro scale surfaces

    表面結構的測量與特徵描述是精密計量技術的一個要方面,傳統上包括將輪廓情況根據不同的波長范圍劃分為粗糙度、波紋度和形狀及后續的數字量化.按得的參數檢查它是否為公差允許,以保證零件執行其定的.當技術特性已經經過仔細確定,並且其過程穩定時,該方法是人滿意的;但是,當製造過程正在進行中或過程的不穩定、過程變化使技術特性失效時,就需要研究和表現及過程評定相關的表面參數.討論了表面結構的分類與識別問題.同時闡述了為此目的而開發的先進技術及其應用.所研究的技術對從納米尺度到傳統的微米尺度的較大帶寬范圍內的表面特徵描述都是有效的
分享友人