按進位轉移 的英文怎麼說

中文拼音 [ànjìnwèizhuǎnyí]
按進位轉移 英文
jc jumon carry
  • 按 : Ⅰ動詞1 （用手或手指壓） press; push down 2 （壓住; 擱下） leave aside; shelve 3 （抑制） restrain...
  • 進 : 進構詞成分。
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 轉 : 轉構詞成分。
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  • 轉移 : 1 （改換位置） shift; transfer; divert 2 （改變） change; transform 3 [醫學] （擴散） metastasis;...
  1. According to the frndamental and the steps of this method, we cans use the linear regress filter method to make the simulation of the wind load and then we can educe the curve of the time - process wind velocity. after that step, we can get the chart of the dynamic wind load which we can deliver the crosswind into the particle wind load and put them on the corresponding cell nodes. then we can do the analysis of the dynamical wind load through the time - process analysis to get the max value of the displacement

    根據線性回歸濾波器法的基本原理和步驟，藉助相關軟體進行風荷載的人工模擬並得出風速時程曲線，進而轉化為風動力譜，由此將橫風向風力表達成節點風荷載作用於相應的單元節點上，按時程分析法對該空間桁架體系進行風荷載的動力分析，求出結構在進行風動力荷載分析時，結構相應節點對應的最值位移值。
  2. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  3. A moderate separation of the decision - making power is needed so as to meet the demands of the localities. as a necessary component of environmental and institutional construction, the government should take into consideration how to define government function in alleviating poverty under the market economy system and how to reform the fiscal and tax system and the financial transfer payment system. the application range of the poverty - reduction model should also be distinctly defined

    此外，作為模式運行的配套環境和制度建設，本文著重提出：要明確市場經濟條件下政府反貧困職能的定位；進一步完善財稅體制和財政間轉移支付制度；要明確界定開發式扶貧模式的適用范圍，按照統籌城鄉經濟社會發展的思路，逐步建立中國農村基本社會保障制度，以提高扶貧整體成效。
  4. Then figure out the wind load in term of the load criterion and the wind tunnel test results separately. by comparing with the two results, we can draw a conclusion that the values which generated by the load criterion are bigger than these ones generated by the other. in order to calculate and design in the worst situation, the paper select the bigger basic wind stress and then turn the area - load into liner - load to receive the displacement of the nodes and the internal force of the cells generated by the static wind load

    由此，得出用於作業棚結構設計的數據，進而按建築荷載規范和風洞試驗數據分別計算出風荷載標準值以及基本風壓，通過對兩種靜力風荷載計算的結果進行比較，可以看出，按規范計算風荷載的結果在結構的整體計算中偏於保守。按照最不利情況計算的設計準則，本論文選用較大的基本風壓值按受力面積分配的方法把面荷載轉化為線荷載代入midas運算程序中，求得該結構在該靜力風荷載作用下的節點最值位移。
分享友人
分享到 Line

分享到臉書