排出溫度 的英文怎麼說

中文拼音 [bèichūwēn]
排出溫度 英文
discharge temperature
  • : 排構詞成分。
  • : Ⅰ形容詞(不冷不熱) warm; lukewarm; hot; gentle; mild Ⅱ名詞1 (溫度) temperature 2 (瘟) acute ...
  • : 度動詞[書面語] (推測; 估計) surmise; estimate
  • 排出 : discharge; exhaust; squeeze; transpire; eject; snapout; vent; mobilize; pump
  • 溫度 : [物理學] temperature
  1. Experimental studies on s1a - 02 gas turbine with water injection into compressor interstage / inlet as well as that on turbocharger self - loop test rig with inlet water injection are introduced. test results are in good accordance with simulation results, wet compression can lower compression work and increase engine power output so engine performance is enhanced, if engine power output is not changed, efficiencies of compressor and this engine become higher and turbine inlet temperature and fuel consumption become lower and if keeping t4 the same as that before wet compression is used, efficiencies become furthermore higher and engine power output increases greatly

    實驗結果和計算結果同樣表明:濕壓縮減少了壓氣機所消耗的壓縮功,增加了燃氣輪機的輸功率,提高了燃氣輪機性能,如果保持發動機輸功率恆定,濕壓縮可以提高壓氣機和整個燃氣輪機機組的效率,與此同時,渦輪進口t _ 3 ~ *和燃油消耗率下降;如果保持渦輪t _ 4 ~ *恆定,壓氣機和燃氣輪機機組效率進一步提高,燃氣輪機輸功率增加。
  2. In this paper, the sensibility analysis of the factors affecting the temperature in well bore is relatively systematically made by using a large number of the data calculated with the borehole flow and heat transfer 3 ? d numerical model proposed by the author. the study shows that the thermophysical parameters of the drilling fluid and formation, etc. and the entrance temperature and circulating capacity, etc. of drilling fluid have a greater influence on the temperature in well bore. therefore, accurately mastering the thermophysical parameter values of penetrated formation and drilling fluid in well bore, considering the influence of the temperature and pressure on thermophysical parameters and accurately measuring such parameters as entrance temperature and discharge capacity of drilling fluid, etc. are of utmost importance for accurately simulating the temperature in well bore

    利用由作者提的井內流動和傳熱的三維數值模型計算所得的大量數據,文章對影響井內的諸多因素進行了較系統的敏感性分析,研究表明:鉆井液和地層等的熱物理參數以及鉆井液的入口、循環量等對井內有較大影響,因此,準確掌握所鉆地區地層和井內鉆井液的熱物理參數值,考慮壓力對熱物理參數的影響,準確測量鉆井液的入口量等參數值,對于井內的準確模擬至關重要。
  3. With analyzing of the case study and based on simulating and analyzing quantitatively, this article, considering the goal of the performance - based fire - protection design is protecting occupants from being injured and keeping buildings from being damaged, thought that fire compartmentation of a large building of saling books can be divided according to their saling malls and fire compartmentation in the saling mall can be separated by the fire - proof screen. on the evacuation design, the quantity of safety exits around these buildings and the evacuation width should be increased if possible and the safety exit number, exit width and evacuation distance can be determined according to the simulating results on smoke layer temperature and height, concentration of co2 and co, occupants evacuation time and visibility. on the means of preventing and discharging smoke, the most proper measure should be determined according to their geometrical characteristics and the natural means of discharging smoke is feasible to the large building of saling books. based on analyzing of smoke

    通過對案例分析研究,本文認為大型書城建築性能化防火設計研究的最終目的是保證人員生命安全和保證建築結構安全,在模擬計算和量化分析的基礎上,大型書城的防火分區可以將中庭連通的書城區域劃分為一個區,在書城場地內可以採用防火卷簾進行防火分區劃分;在人員疏散設計中,應盡可能利用書城賣場的空間設計較多的安全口和增大疏散寬,其安全口數量、寬和疏散距離可以根據人員安全疏散時間和煙氣、沉降高、 co2濃、 co濃、能見模擬計算結果驗證確定;在防煙方式的選擇上,應當根據建築物的幾何特點選取最適宜的措施,就大型書城建築而言,採用自然煙的方式是可行的。
  4. When the chemical ( usually diluted with oil - based carrier ) is heated, it is vaporized in a combustion chamber and then expelled via an outlet tube to form a dense fog cloud when it condenses on contact with cool ambient air

    當化學液體(通常以油劑稀釋)加熱后,經氣管,一旦接觸外界較低的空氣便凝結成一團煙霧。即使地方給茂密的植物或其他
  5. However, this dissertation mainly focuses on diesel catalyst aging mechanism including heat deterioration and performance degradation caused by toxic substance. following the above conclusions, a fast aging test cycle is produced which consists of three stages

    論文的主體分析了柴油機氧化催化劑的老化機理,主要是熱失活和化學中毒老化,研究了我國主要幾種柴油機的特性,並在催化劑老化機理基礎上提車用柴油機氧化催化器快速老化試驗循環,即三段式老化循環。
  6. The air absorbed by the fans is separated in and equably flows in the interior and outer canister, from to the heater and interior canister, the air is efficiently heat - treated, then the hot air influxes to and is balanced in because of the mixing by the heater, the hot airs temperature in has only little change, then it is separated completely from to ensure the balance - dryness of the colophony

    由鼓風機吸入的空氣在處被分散,于內筒和外筒間均勻地流動,從處進入內筒和加熱管進行有效地熱交換。然後熱風在處匯集,在處無序混亂的熱內被均化。由於加熱箱熱風混合效果的作風,處的熱風變化幅很小,熱風經熱風口被完全均勻地分散開,從而保證了樹脂均勻乾燥。
  7. He would have to evaporate 100 pounds of perspiration per hour to keep his skin temperature below the boiling point of water

    同時,每小時他還得一百磅的汗液,以保證皮膚低於沸點。
  8. As an arrangement invisibly made by our dear master, everything proceeded marvelously in this beautiful place, where an atmosphere of great tranquility prevailed, and there were sunny days, starry nights, and therapeutic thermal baths with pristine waters of up to 70 degrees celsius 250 meters from the retreat venue

    而師父在無形中為我們所安的這個美麗的場地,更處處令我們感到驚喜,不僅有著全然寧靜的氣氛,白天時陽光和煦,到了夜晚繁星滿天,而且還有達70具有療效的原始泉,汨汨而泉距離我們打禪的地方僅有250公尺之遠。
  9. To specify the project, by selecting materials, choosing construction methods, arranging construction process, locating expanding joints, disposing key construction, the outside shell temperature was controlled not exceeding + 25 at surroundings, which met the need of design and check requirement

    針對工程具體情況,通過材料選擇、施工方法確定、施工程序安、膨脹縫的布置、關鍵結構的處理等問題,得使爐墻外壁控制在環境+ 25的范圍內,滿足設計及施工驗收規范要求的方法。
  10. The compressor works continuously to maintain the inside temperature, and the heat it ejects from the back of the fridge offsets the cold at the front

    冰箱的壓縮機必須持續運轉,以保持裏面的,壓縮機從冰箱後面熱氣,與冰箱前面來的冷氣相互抵消。
  11. Giving some suggestions to develop the fuel according to the experiment result. the final experiment result is very good. after using alcohol - blended diesel oil in diesel engine, the power can be achieved, the let of contamination is reduced, thermal efficiency enhanced, the exhaust degree and the max combustion pressure is steady

    對理論和實驗結論進行總結,對課題的發展提建議實驗的最終數據證明:在柴油機上燃用乙醇柴油后,能夠達到原機的功率,並且柴油機的放狀況有很大的改善,熱效率有一定的提高,和最高燃燒壓力基本不變,實驗結果是比較理想的,可以考慮在實際中應用和推廣乙醇柴油。
  12. The ideal operational value of waste - gas temperature is provided through combining the boiler ' s practical operation and the research of heat loss due to exhaust gas, which offers important theory and paves a solid way in optimizing boiler operation

    通過對煙熱損失的研究,並結合鍋爐的實際運行情況,提的運行目標值,此目標值的確定對于鍋爐運行優化有著重要的理論基礎。
  13. Abstract : the causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    文摘:分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水,蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰,高,煙氣熱量未回收利用以及爐子保襯里效果差等問題,提採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明,本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題,提高了保效果,減少散熱損失1 . 25 % ,降至170左右,裝置的爐效率由83 %左右提高到90 %以上
  14. The causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水,蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰,高,煙氣熱量未回收利用以及爐子保襯里效果差等問題,提採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明,本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題,提高了保效果,減少散熱損失1 . 25 % ,降至170左右,裝置的爐效率由83 %左右提高到90 %以上
  15. The conclusion is drawn that in the quasi two - stage compression heat pump system coupled with ejector, discharge temperature of the compressor is decreased effectively, electric power is reduced, and heating performance is increased compared with those of the flash - tank throttle system in the same conditions. it shows that the quasi two - stage compression heat pump system coupled with ejector improves performances of air - source heat pump in theory

    由結果可以看:在相同工況下,準二級壓縮?噴射復合熱泵系統可以有效降低壓縮機,所消耗的電功率較閃發器節流系統有所降低,制熱性能有所增加,從理論上說明該系統在解決空氣源熱泵低適應性問題上有進一步突破。
  16. The intention of this article is experimental study and exploration to the operation tuning and renovation regarding the problems found in the general commissioning and operation of the first imported 660mw unit with w flame such as insufficient mill output, higher ah inlet gas temperature and exhaust gas temperature than design value

    本文針對首臺引進660mw機組w型火焰鍋爐整體調試及運行中存在的磨煤機力達不到設計值和空預器入口煙高於設計值等問題,進行了運行調整和改造試驗研究。
  17. This new system followed diesel engine from manufactory to ship takes both performance moniting in real time and technical state analysis of diesel engine. the usage of the collecting - distributing data collecting structure, the communication net conbined rs - 232 with rs - 422 and object - oriented programme language makes this new system easy to develop and reliable to use both hardware and software

    本系統的數據採集採用集散型結構,上位機採用pc機,下位機採用6個單片機數據採集模塊既柴油機燃油噴射和燃燒過程數據採集模塊、柴油機數據採集模塊、柴油機滑油壓力和數據採集模塊、柴油機冷卻水系統數據採集模塊、柴油機輔助設備數據採集模塊、數據輸模塊。
  18. The deficient mill output has been finally resolved by two renovation programs for the classifier and the central air pipe of d - 12 - d double - in and double - out mill, one of the biggest pulverizes ; higher ah inlet gas temperature and exhaust gas temperature also rectified by refractory modification and the tuning of sootblower " s running mode

    對世界最大的d - 12 - d雙進雙磨煤機的分離器和磨煤機中心風管等部位通過兩種方案的改造試驗最終解決了該磨煤機的力不足問題;通過對衛燃帶改造和調整吹灰器的運行方式解決了空預器入口煙高的問題。
  19. A ejector for is applied in this theory. it can not only regulate the evaporating temperature of each high - temperature refrigeratory but also reduce the back - pressure of the compressor when a system applies this theory. at the same time, the exhaust temperature of the compressor becomes low and the refrigerating capacity per unit of swept volume becomes high

    鑒于目前這種現狀,本文提了以噴射器為基礎的船舶高、低冷庫製冷新循環,不但可調節高庫的蒸發,而且也可使壓縮機的回氣壓力得到提高,壓縮機降低,單位容積製冷量上升,製冷系數提高,火用效率提高。
  20. The corresponding learning algorithm is given and the effectiveness of this method is proved by the prediction of exhaust gas temperature in aircraft engine condition monitoring

    了相應的學習演算法,並以飛機發動機狀態監控中發動機的預測為例驗證了模型和演算法的有效性。
分享友人