排氣管總成 的英文怎麼說

中文拼音 [bèiqìguǎnzǒngchéng]
排氣管總成 英文
entlueftungsrohr
  • 排 : 排構詞成分。
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 總 : Ⅰ動詞（總括; 匯集） assemble; gather; put together; sum up Ⅱ形容詞1 （全部的; 全面的） general; o...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 排氣管 : escape pipe; gas vent; exhaust shaft; stack; exhaust pipe; nozzle; stem; tail pipe排氣管道 discha...
  • 排氣 : [機械工程] exhaust; aerofluxus; air out; exit gas; ventilate; atmosphere; vent排氣泵 exhaust pump...
  1. In the third, this paper makes a survey on components of the exhausted flue gas and waste heat resource, and discusses the possibility and methods of steam generation and air preheating with the waste heat. and then, the analysis on the advantages and disadvantages of heat recovery plants with conventional steel - water heat pipes and inorganic heat - transfer heat pipes is carried out. the paper also gives a valuation about the plan and features of the design of heat recovery

    對余熱源排煙的成分和余熱資源量進行標定，討論余熱回收產生蒸汽或加熱燃燒用空氣的可行性和方法，分析常規余熱回收技術設計、採用普通鋼-水熱管和無機傳熱熱管等傳熱元件的設計余熱回收裝置的優缺點，並對余熱回收設計方案及其特點進行總體評價。
  2. In this thesis hydraulic experimental studies and theoretical analyses on the vortex - flow drop shaft were conduced and the following results were accomplished : ( 1 ) in the model test some hydraulic characteristics including the shape of air core in the center of the drop shaft, the radial distribution of water flow velocity and the distribution of pressure on the wall of the drop shaft were measured under the condition of high water head above 250m and large discharge above 1400m3 / s. ( 2 ) a kind of computational method for the spiral water flow in the air core region of drop shaft was discussed and applied and the results agree the experimental data well. ( 3 ) the total ratio of energy dissipation in the drop shaft can reach 90 % and the energy dissipation in every region was discussed quantitatively

    本文通過試驗研究與理論分析對旋流式豎井泄洪洞應用於高水頭、大泄流量情況時存在的一些水力學問題進行了研究和探討，取得以下主要成果：一、結合小灣工程導流洞改建，對高水頭（ 252m ） 、大泄流量（ 1400m ~ 3 s ）條件下旋流式豎井中的水流運動特徵進行了比較全面的測量，包括空腔形態、徑向流速分佈及井壁壓強等；二、提出了豎井空腔段螺旋水流水力計算方法，其計算結果與實測值吻合良好；三、利用試驗與計算結果，對旋流式豎井的消能機理進行了探討，對豎井各部分的消能能力有了總體認識；四、對豎井下部消力井的合理井深進行了優化試驗研究，發現消力井合理深度為0 . 9d左右；五、通過試驗研究，歸納出豎井水流總摻氣量估算方法，為導流洞排氣方案的設計提供了參考依據；六、在高水頭、大流量條件下，豎井空腔段下部流速很高，盡管水流螺旋運動引起的離心力可以確保井壁壓強保持正壓，但空化數依然較低，因此豎井的空化空蝕始終是工程界關注的重大問題。
  3. Abstract : optimum distances between primary nozzle exit and mixing tube inlet, static pressure recovery of the mixing flow in mixing tube 、 total pressure distributions at the exit of mixing tube 、 pumping coefficients and total pressure losses of the exhaust ejector systems with four different types of primary nozzles have been measured in the experiments

    文摘:對4種主噴管組成的排氣引射系統的引射系數和總壓損失、各主噴管出口與混合管進口之間的最佳間距、混合氣流在混合管內的靜壓恢復及混合氣流在混合管出口處的總壓分佈等進行了測量和對比。
分享友人
分享到 Line

分享到臉書