接觸次序 的英文怎麼說

中文拼音 [jiēchùcìxù]
接觸次序 英文
contact series
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 次 : Ⅰ名詞1 （次序; 等第） order; sequence 2 [書面語] （出外遠行時停留的處所） stopping place on a jou...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  • 次序 : order; sequence; succession; arrangement
  1. They sequenced the genetic code of a sars virus taken from one of the first known carriers of the disease, and of sars viruses found in four people in singapore who had had direct or secondary contact with that individual

    他們排序了sars病毒的遺傳密碼，這些病毒取自於最先發現的病人中的一位，也取自於在新加坡直接或二次接觸這些病人而染毒的4位病人。
  2. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  3. As a part of the civil 863 plans, two multiple - contact models for two kinds of braking system are built in the paper, in which contact fields are described as coons surfaces, initial velocity is programmed in fortran. the thermal - mechanical coupling braking processes are simulated for the first time by msc. marc, the general - used nonlinear fem software. time distributions of the velocity, the stress and the temperature of the components under various initial velocity and brake force are obtained, which offer theoretic gist to study the life of the wheel, the disc and so on

    作為國家行業863重大課題《鐵路機車車輛虛擬樣機系統》的一部分，本文在研究接觸問題和熱?機耦合問題數值方法的基礎上，採用國際上通用的非線性有限元分析軟體msc . marc建立了踏面制動和盤形制動主要部件的多體接觸計算模型，其中用解析方法描述，即用nurb曲線、高斯曲面來描述接觸區域，用fortran語言編寫定義初速度的用戶子程序，首次對兩種制動過程熱?機耦合進行了數值模擬，定量給出了主要制動部件在不同初速度、不同制動力下各個時刻的速度、應力和溫度的變化規律，為研究車輪、閘瓦以及制動盤壽命提供了理論依據。
  4. Purpoose ： sorting the plastic bottles of pell - mess status in order and feed them to the air conveyor in connection with the downstream machine such as rinsing and filling machine, the machine replaces the traditional handling of empty bottle by hands therefore labor force has been liberated and productivity has been increased significantly, meanwhile second contaminationcaused by hand touching pet bottle is avoided consequently

    用途：把雜亂無章的塑料瓶整理後有次序有方向的排列在輸送機上，送入其它設備，完成下道工序（如沖瓶、灌裝等） ，降低了工人勞動強度，提高生產效率，同時也避免聚酯瓶因人手接觸而造成的二次污染。
  5. Purpose : unscramble the plastec bottles, then transfer them to conveyor in order and certaindirection and feed them into other eqrupments to finish next procedure ( such as rinsing and fillingetc ), decrease labor intensity and inprove productivity effect, also avoid second time contamination caused by hand touching pet bottle

    用途：把雜亂無章的塑料瓶整理後有次序有方向的排列至輸送機上，送入其它設備，完成下道工序（如沖瓶、灌裝等） ，降低了工人的勞動強度，提高生產效率，同時也可避免聚脂瓶因人手接觸而造成的二次污染。
分享友人
分享到 Line

分享到臉書