接觸步驟 的英文怎麼說

中文拼音 [jiēchùzhòu]
接觸步驟 英文
contact procdeure
  • : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
  • : Ⅰ動詞1 (接觸) touch; contact 2 (碰; 撞) strike; hit 3 (觸動) touch 4 (感動) move sb ; sti...
  • : Ⅰ名詞1 (步度; 腳步) pace; step 2 (階段) stage; step 3 (地步; 境地) condition; situation; st...
  • : Ⅰ動詞(快走) (of a horse) trot Ⅱ形容詞(急速) rapid; swift Ⅲ副詞(突然; 忽然) suddenly; abruptly
  • 接觸 : 1. (交往) come into contact with; get in touch with 2. (沖突) engage 3. (挨上; 碰著) contact; touch
  • 步驟 : step; move; procedure; measure
  1. Step 1 : connect the channels with the tongue touching the upper palate

    1 :連渠道,並與舌及上齶
  2. Hands should be washed before and after contact with any patient, after activities likely to cause contamination and after removing gloves

    任何病患之前和之後,執行有可能引起污染的之後,以及脫手套之後,都要洗手。
  3. Staff involved in the triage process should wear a face mask ( see below ) and eye protection and wash hands before and after contact with any patient, after activities likely to cause contamination and after removing gloves

    參與篩檢過程的人員應戴口罩、眼睛護具;任何病患之前和之後,執行有可能引起污染的之後,以及脫手套之後,都要洗手。
  4. The gap element method is proposed in the paper for two kinds of problems, which include contact problem and gap joint problem. elasticity contact problem falls into the category of unknown boundary value problems. it follows that the contact area and contact conditions or states ( st

    文中給出了間隙元法在空間可動部件問題中的應用,推導了其幾何邊界條件和力學邊界條件,利用虛功原理推導了含間隙元彈性問題的有限元方程式,給出了其數值解法的迭代,並指出了利用間隙單元進行分析的特點。
  5. In winchester disk technology, by a read / write head in some magnetic disk unit , to come into contact with the disk surface in a “ landing zone ” as a normal step during deceleration of the disk

    在溫氏磁盤技術中,某些磁盤設備中的讀/寫頭在該磁盤減速制動期間,作為一個標準的操作,進入「合區」並與該區中的磁盤表面的過程。
  6. The bearing spot contact and the friction carries on after the analysis, has carried on the simulation to the bearing work process, from simply established sigin ball two race model to the complex distinction the roller conveyer, the single ball four roller conveyers and the circular roller conveyer single ball four roller conveyer steel wire roller conveyer ball bearing finite element models, introduced the modelling method in detail, the restraint and the load infliction method

    在點和摩擦分析的基礎上,對軸承的工作過程進行了模擬,按由簡單到復雜的研究,分別建立起了單球雙滾道,單球四滾道和圓環形滾道單球四滾道的鋼絲滾道球軸承有限元模型,解決了建模模擬過程中實體模型的建立,約束和載荷的施加等一系列問題。
  7. This review summarizes various ways to make occupational exposure assessment of benzene, the procedure of assessment, the grading of results, the application of exposure assessment

    摘要該文綜述了對工業溶劑苯的各種評估手段、評估、結果分級及進行評估的意義。
  8. 1 resin with bad wetness systems such as epoxy resin, polyester, alkyd, acrylic resin, use compound with the surface active agent, and the thixotropic grind materials can be acceptable. operate as following process : add paint material all kind of resin and the solvent - add the organic bentonite pre - gel, stir enough - add the pigment, stir and disperse enough - dilute

    1潤濕性比較差的環氧,聚酯,短油酸樹脂,丙烯酸樹脂等與表面活化劑合用,且變性研磨料科被受的情況下,按照以下操作:加油漆和溶劑混合加入有機預凝膠充分攪拌分散加入顏料充分攪拌分散稀釋。
  9. Taking a rotor shape parameter as a variable, the minimum volumes of rotor cavity and pump flow as the design objectives, as well as some constraints on rotors and gears cavity structures, an optimization design model of un - contact rotor pump was constructed

    摘要以轉子形狀參數為變量,以流量和轉子腔體積最小為設計目標,考慮齒輪腔和轉子腔結構的有關約束,建立了非式轉子泵的優化設計模型,給出了優化設計
  10. Activation : to activate a power stone, a manifester must mentally contact it. doing so involves several steps and conditions

    啟動:顯能者必須與靈能石進行精神以啟動它。這包括以下和條件。
分享友人