接觸粘合 的英文怎麼說

中文拼音 [jiēchùniángě]
接觸粘合 英文
contact bonding
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. Tensile properties and impact properties measurements were done at room temperature. the volume resistivity of rectangular samples was measured using a zc36 electrometer and a high 240a voltage supply, for samples with a low resistivity level a dt - 9205b digital multimeter was used, silver paint was applied to ensure complete contact between sample and electrodes, namely, to eliminate the contact resistance. the phase morphology of blends was also studied using a jeol jsm - 5900lv scanning electron microscope ( sem )

    體積電阻率的測定：當r _ v 10 ~ 8時，製成100 100 4mm板材，用zc36型高阻儀測量；當r _ v 10 ~ 8時，用dt - 9205b型數字式萬用表測試試樣的體積電阻，為了減小接觸電阻對測試的影響，採用銀導電膠將銅片粘接在試樣的兩個端面上，靜置24小時，待銀導電膠凝固，試謝長瓊:熱拉仲對pet / pe / cb復合導電體系形態和性能的影響樣的電阻穩定后再測量。
  2. The sort, material composite, structure properties and conduction mechanisms of eca ( electrical conductive adhesive ) were discussed in this paper. then three types of ega specimens were designed and made, on which temperature cycles test from - 55 ? to + 125 ? and thermal aging at + 125 ? were carried out. changes of the adhesive strength, eca ' s bulk resistance and contact resistance under the environment stress were summarized and a detailed evaluation on these specimens was given

    本文在全面闡述導電膠的分類組成、物理結構、導電機理的基礎上，設計並製作了三批導電膠樣品，通過對樣品進行長時間的- 55 ? ? + 125溫度循環和125高溫存儲試驗，總結了導電膠粘接強度、體電阻和接觸電阻在環境應力下的變化規律，對三類樣品的長期可靠性做出了全面的評價，並結合導電膠電阻率和「穿流閾值」的計算機模擬，給出了提高導電膠可靠性和電導率的建議，介紹了國內外在高電導率高可靠性導電膠研製方面的一些最新進展。
  3. Although numerical methods have frequently been used in the study of frc, theoretical analyses of such test methods as pull out tests and single fiber fragmentation tests, seemingly simple, remain to be challenging problems. problems arise when other factors are considered in connection with the various numerical models. these factors include nonlinearities in the properties and / or geometries of the materials, influences of such environmental conditions as temperature ( which is also to be studied in the present work )

    本論文正是針對以往研究中的不足，在對纖維增強復合材料破壞問題進行數值模擬的研究中，綜合考慮了纖維和基體材料的非線性效應、纖維和基體材料受外載發生大變形時的幾何非線性，以及纖維基體之間界面脫粘時接觸單元的非線性效應。
  4. The results of numerical simulations and analytical solution show good accordance, except in the region near the fiber ends, where the shear - lag approach causes considerable discrepancy. next, to overcome the unrealistic assumption of perfect bonding, augmented - lagrange contact algorithm, element " birth - death " and fem are combined in the study of the partial debonding between fiber and matrix under pull out forces

    然而完全粘結的假設過于理想，與實際應用相差較大，因此，本論文將有限元法，接觸演算法和單元生死法結合起來，研究較大抽拔力作用下，纖維與基體之間發生的逐步脫粘的過程，所得到的抽拔力的變化結果，與試驗數據比較，較為一致。
  5. Adhesives - wettability - determination by measurement of contact angle and critical surface tension of solid surface ; german version en 828 : 1997

    粘合劑.可濕性.固體表面接觸角度和臨界表面張力測量
  6. En 828 adhesives. wettability. determination by measurement of contact angle and critical surface tension of solid surface

    粘合劑.親水性.通過固體表面首要表面張力和接觸角度測定
分享友人
分享到 Line

分享到臉書