接觸頻率 的英文怎麼說

中文拼音 [jiēchùbīnlǜ]
接觸頻率 英文
contact frequency
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 頻 : Ⅰ形容詞（次數多） frequent Ⅱ副詞（屢次） frequently; repeatedly Ⅲ名詞1 [物理學] （物體每秒鐘振動...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  • 頻率 : frequency; rate
  1. The ultrasonic dynamic contact of bolt - clamped transducer and rigid plane are modeled using hertzian contact theory, and the analyzing results reveal that the nodal plane of the bolt - clamped transducer is levitated in normal direction by the ultrasonic dynamic contact action, and the real area of contact of bolt - clamped transducer and rigid plane decreases in the same time

    首先利用赫茲接觸理論建立了夾心式換能器和剛性平面的超聲動態接觸模型。通過對模型進行分析、求解表明，在縱向超聲頻率動態接觸作用下，換能器節面位置產生了上浮，換能器端面與剛性平面的動態真實接觸面積比靜態時減少了。
  2. First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in ug software. the elastic contact problem is analyzed in finite element method ( fem ) and is used to the parameters " distribution and contact stress of the joint are obtained on the base of ansys code. with the effect factor of load frequency, the prediction method of fretting fatigue life of dovetail joint under low and high / low cycle complex load is proposed

    本文介紹了微動損傷的機理和微動疲勞壽命的研究方法；利用ug軟體對燕尾榫聯接結構創建了參數化實體模型；基於ansys軟體平臺求解彈性接觸問題，獲得了榫聯接結構接觸應力及接觸狀態量的分佈；在已有微動疲勞壽命預測模型的基礎上，引入載荷頻率影響因子，對低周、高低周復合載荷作用下的燕尾榫聯接結構進行了微動疲勞壽命的預測，與試驗結果對比表明採用本文提出的方法預測榫聯接結構的微動疲勞壽命是有效的。
  3. The empirical analysis, using probit model, showed that the extension efficiency of the technique was obviously affected by following factors : income and cost, yield increase, farmers " age and education, non - agricultural income, farmer ' s social status, distance from town, frequency of farmers " contact with media and agricultural technicians

    運用probit模型對超高茬麥田套稻技術推廣的影響因素進行分析，結果顯示畝增收節本、畝增產量、戶主年齡、戶主受教育時間、非農收入、是否幹部、離鎮距離、媒介頻率、與農技人員接觸次數對該技術的推廣有顯著影響。
  4. A new method for measuring the vibration of shadow mask without touch by detecting the light density with reflection type optical fiber sensor is presented. the measurement system based on the new method is designed to make the vibration measurement easier working, faster calculating, and get more precise results. it is an important measurement and analysis tool to improve the performance of shadow mask and display quality of cpt

    本文提出了基於單光纖光強度反射法的非接觸式微振動測量系統的原理，並設計製造了該測試系統，探索出了簡單方便可靠的測量方法，能夠準確客觀地反映蔭罩振動的各項參數（各振動模的振動頻率、振幅、衰減時間） ，實現了測試裝置的簡便化和測試過程的自動化，為cpt張緊式蔭罩系統的性能改進與顯示質量的提高提供了有效的測試分析手段。
  5. 0. 1in connectors for frequencies below 3 mhz. part 11 : edge socket connectors with closed ends and having a contactspacing of 2. 55 mm 0. 1 in mating either with board mounted connectors or printed wiring boards with edge board contacts

    頻率低於3mhz的連接器.第11部分:與印製電板裝連接器或板邊具有接觸點的印製線路板相配用的帶封閉端的觸點間距為2 . 55mm
  6. Multiple funcyions available : start / crater arc current, increase / decrease time, base, crest value current, pulse frequency, pulse rate, post flow time, hf / friction welding, water / gas cooling

    功能豐富：起始/收弧電流、上升/下降時間、基值電流、峰值電流、脈沖頻率、占空比、滯后關氣時間分別可調，高頻/接觸引弧、水冷/氣冷可供選用。
  7. Principal conclusions were drawn as the following : the non compatibility of pressure or velocity of the gas on both sides of the contact surface is the cause of the formation of shock wave ; the heating effect of reflective shock wave to driving gas during charging or exhausting process is the internal mechanism of peak oscillating effect, and all the factors that influence the formation and the running of the shock wave will influence the peak oscillating frequency, cooling effect

    主要結論如下：熱分離機內激波形成的原因是射氣瞬間接觸面兩側壓力和速度不相容；峰值振蕩效應的內在機制為反射激波對充氣階段的驅動氣或低溫排氣的加熱，凡是影響激波形成及運動的因素都將對峰值振蕩頻率、冷效應及熱效應產生影響；當充、排氣時間比為0 . 1763時，最佳射流激勵頻率出現在高階峰值振蕩頻率上。
  8. The distribution of magnetic induction in rectangular soft - contact mold during electromagnetic continuous casting ( emcc ) was investigated considering the electric frequency

    摘要研究了在電磁軟接觸連鑄過程中，電源輸入頻率的變化對矩形電磁軟接觸結晶器內的磁感應強度分佈規律和彎月面變化情況的影響。
  9. The new technology of non - contact life - parameter detection is relative to that of the normal contact one, which uses microwave beams to illuminate the human subject, whose reflected wave will be modulated by the surface movement resulting from the physical activity. by this way, some parameters of the reflected wave, such as frequency and phase will be changed. if these changes can be detected, the life parameters such as respiration rate and heartbeat rate will be extracted from those changes

    非接觸生命參數檢測是相對于常規的接觸式檢測而言的一種新技術，它利用微波束照射人體，其回波信號被人體生命活動引起的體表微動所調制，使得回波信號的某些參數（如頻率、相位）發生改變，檢測到這些變化就能從中提取出人體的生命參數（如呼吸或心跳） 。
  10. Rectangular connectors for frequencies below 3 mhz ; part 8 : detail specification for connectors, four - signal contacts and earthing contacts for cable screen

    頻率低於3mhz的矩形連接器.第8部分:電纜屏蔽用四信號觸點和接地觸點連接器詳細規范
  11. Yet generally speaking, their command of english is far better than cl

    新加坡年輕一代的華人由於接觸英語的頻率遠勝于華語，大部分的英語能力都比華語略勝一籌。
  12. Therefore, pulls out delivers the frequency to be higher, with are more in the unit interval / unit time internal contact ' s opportunity, this may enable the main center in unit of time to obtain more information, is easier the excitable pleasant sensation response

    因此，抽送頻率越高，與在單位時間內接觸的機會就越多，這就可以使性中樞在單位時間內得到更多的信息，就更容易激發性快感反應。
  13. How long have you know the applicant and in what context ? please comment on the frequency of your interaction

    您認識申請人有多久?請說明你們的接觸頻率。
  14. At last, in according to the experiment results, the interpretation of the mechanism of the slip phenomenon of prepressing - contact spring - damping system was given in this dissertation. further more, the relationship among the limit frequency, the value of prepressing, excitation frequency, the amplitude of excitation and the materiel parameter was analyzed. base on the theory analysis the limit frequency formula was given, and the contact - slip condition for engineering application was concluded

    最後根據理論研究與試驗分析的結果，分析預緊接觸式彈簧阻尼系統產生滑移現象的機理以及共振峰值漂移現象的理論解釋，並通過定性分析接觸分離時的頻率與預緊量、激勵頻率、激勵力幅值以及墊層的材料參數之間的關系，提出能定量描述系統出現滑移現象的極限頻率公式，總結了預緊接觸式結構始終保持接觸的條件。
  15. 0. 10in connectors for frequencies below 3 mhz for use with printed boards. part 3 : two - part connectors for printed boards having contacts spaced 2. 54 mm o. 100 in centres and staggered terminations at that same spacing

    印製板用頻率低於3mhz的連接器.第3部分:觸點中心相隔距離和交錯線端子相隔距離為2 . 54mm
  16. 0 75in connectors for frequencies below 3 mhz for use with printed boards. part 4 : two - part connectors for printed boards having contacts spaced at 1. 91 mm 0. 075 in centres and staggered terminations at that same spacing

    印製板用頻率低於3mhz的連接器.第4部分:觸點中心相隔距離和交錯線端子相隔距離均為1 91mm
  17. The rf frequency, its propagation mode and the calculation of the electric field are analyzed

    基於隧道壁的特性以及接觸網和軌道的存在，對于應用頻率、傳輸模式、場的表示給出了符合實際的分析。
  18. In this part, the high - frequency series inverter with resonant pole capacitor is introduced mainly. the current - exchanging processes of the inverter in different working modes are analyzed, how to reduce the switching loss is discussed, and the calculating methods of snubber capacitor c, factor angle switching frequency and pulse width pw are given in optimum switching process. and results of simulation and experiment verify the validity of theoretic analysis

    接著重點研究了含有諧振極無損緩沖電容的逆變器，對其換流過程中的不同工作狀態進行分析，討論了如何減小逆變器的開關損耗，給出了最佳工作狀態下緩沖電容c 、感性角、開關頻率、觸發脈沖的脈寬pw的詳細計算方法，並通過大量的模擬和實驗波形證明了理論分析的正確性。
  19. Rectangular connectors for frequencies below 3 mhz ; part 2 : detail specification for a range of connectors, with assessed quality, with trapezoidal shaped metal shells and round contacts ; fixed solder contact types

    頻率低於3mhz的矩形連接器.第2部分:帶質量評定的帶梯形金屬套和圓形接觸件的連接器系列的詳細規范.固定的的釬焊接型
  20. Rectangular connectors for frequencies below 3 mhz - part 2 : detail specification for a range of connectors, with assessed quality, with trapezoidal shaped metal shells and round contacts - fixed solder contact types ; amendment 1

    頻率低於3mhz的矩形連接器.第2部分:帶質量評定的帶梯形金屬套和圓形接觸件的連接器系列的詳細規范.固定的釬焊接型.補充件1
分享友人
分享到 Line

分享到臉書