接軋板軋機 的英文怎麼說
中文拼音 [jiēyàbǎnyàjī]
接軋板軋機
英文
fish plate pass-
In this paper, the large non linear fem software marc be used to calculate the 3d deformed distribution of the cold roll forming machine frame, slide seat and bolster plate
摘要以大型非線性有限元軟體marc為分析工具，建立接觸分析模型，對冷滾軋機床機架、滑臺及墊板進行三維有限元彈性接觸分析，給出機床三維變形狀態的定量描述。In order to make the camber design easier and keep contact pressure equal along rolls, we shall assume the pressure distribution to be quadratic along the width and the marginal deformation to be planar
摘要為了使中厚板軋機輥型設計快捷且保持輥間各點接觸壓力相等，利用了壓力沿板寬方向呈二次分佈、板邊緣處變形為平面變形的計算處理，從而使輥型設計更為方便。Besides the design of the hardware construction for shape meter, the software system written in visual basic 6. 0 is also developed. the real - time data acquisition and conversion system worked in interrupt mode is accomplished by means of loading dynamic linkage library of pcl - 812pg enhanced multi - lab card. the converted data processing will be operated then, for example, scale operation, comparison, graphic display, data storage, etc. the adjusting values for the shape control are also calculated in it
本文在參考大量帶材標準板形、軋制初始量設定、調節量計算研究的基礎上，確定了標準板形模型、設定模型、調節控制模型等數學模型；並給出了其相應的演算法；完成了板形儀計算機控制系統的硬體設計，並在此基礎上，應用高級開發語言visualbasic6 . 0 ，通過加載pcl - 812pg多功能數據採集卡的驅動程序后，調用動態鏈接庫（ dll ）中的函數的方法，完成了信號中斷方式下的實時數據採集，採集的數據經計算機作標度變換、對比、圖形顯示、存儲等處理，並提供了用於板形閉環控制的調節量。The overhead traveling crane used at a cold strip mill factory is given to study the deformation, stress distribution and load capacity of the main girder with 3d - fea shell - to - solid submodel method
以某冷軋帶鋼廠橋式起重機偏軌箱形梁為例，採用三維有限元法「板到體子模型」技術，比較分析了加強板2種焊接方式下主梁的變形、應力分佈和承載能力。And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array
本文採用ansys / ls - dyna計算程序為分析工具，對鋸齒形雙金屬復合板成型過程進行計算機數值模擬，在對軋制過程模擬時，針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件間的接觸、軋件間的接觸以及模型的加載等問題，給出了在ansys / ls - dyna中相應的解決方法：應用nodetosurface接觸方式，設定相應參數，選用雙線性等向硬化模型，載荷作為array施加在剛體質心。After long - term application on hot wide strip mills, varying contact rolling technology was proved to be effective in strip profile and flatness improvement roll consumption reduction and increase of rolled product length of rolling cycle
通過在寬帶鋼熱連軋機上的長時間應用證明：變接觸軋制技術可以顯著改善軋后帶鋼的板形質量、降低軋輥消耗和增加軋制單位公里數。分享友人