控制溫度試驗 的英文怎麼說

中文拼音 [kòngzhìwēndùshìyàn]
控制溫度試驗 英文
controlled thermal severity test
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 溫度 : [物理學] temperature
  • 試驗 : trial; experiment; test
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. The air codling system have been installed in open and semi - closed livestock houses. the experimental result revealed that the range of average temperature is reduced about 4, and the rh is about 80 percent, this environment can reduce the swine heat resistant. 5

    將本降溫系統實際使用在開放式豬舍中，進行了系統的初步生產試驗，由試驗數據表明，舍內控制區域內平均溫度下降4左右，相對濕度在80人右，對豬八的生tffi環境沒有產生太人的矽，向，能夠人效的緩解豬只a多的熱應訊5
  3. There are over 80 sets test apparatus in tech - innovation centre, including : anechoic chamber, vibration tester, vibration measurement analysis, impact instrument, constant temperature and humidity facilities. salt spary test case, circle insulation withstand voltage tester, insulation resistance tester, withstand voltage tester, electric lead tester, electrical leakage tester, earth resistance tester, chassis dynamometer, chassis dynamometer control system, high stability dc resistance tester, electrical capacity tester, temperature rise test system

    中心擁有各類分析測試儀器和試驗裝置80餘臺套，包括：消音室振動臺噪聲振動測試分析系統沖擊儀恆溫恆濕實驗儀鹽霧試驗箱匝間耐壓分析儀絕緣電阻分析儀對地耐壓分析儀泄露電流測試儀對地電阻測試儀測功機測功機控制系統高精度直流電阻測試儀電參數測試儀帶電溫升測試儀復合式三坐標測量儀萬分投影儀及電功測試分析系統等。
  4. Integrated the work on theory and experiment, the paper provides technical performance material at large about the automating and humidifying character of the centrifugal nozzle with firing pin type, high pressure and little aperture to the manufacture and user. with the valuable reference during the selecting the equipment and ascertaining the parameters, the users could select and control the humid parameter

    課題的理論與試驗兩方面工作相結合，為撞針型高壓小孔徑離心式噴嘴的霧化加濕性能提供了較為詳細的技術性能資料，為生產廠家和用戶在設備選型和參數選擇過程中，提供了有價值的參考，便於用戶正確而經濟地選擇、控制濕度參數，有效調節噴嘴孔徑、噴水初溫和噴水壓力的大小。
  5. In recent years, the water - saving and control irrigation technique of rice has diverted from plot experimental and demonstration to lare scale. and has got remarkable economic and social benefits. amed at the characteristics of this irrigation area, optimal selection for water - saving techniques of rice, deciding the amout of leaching water and irrigation modles, investigating the adaptability of the water - saving and control irrigation technique in saline land. studying the increase in production mechanism of the technique are important to extend the technique, to better and develop saline land as well as slick spots. according to the results of field experiments, optimization study was conducted on the water - saving irrigation technique of rice in saline land, the effects of different water - saving irrigation techniques on the physiological indexes and yield of rice were systematically analyzed. by using mutiplepurpose fuzzy optimization method, better. water - saving irrigation technique was selector out, that is. the control irrigation technique in rice. the mechanism of it was analyzed from the aspect of the physiological and ecological saving water of rice to provide the implemental process and technical point ; throgh the quantitive analysis and comparision on control irrigation and control class ( flood irrigation ), high production and quality mechanism of the technique was analyzed in terms of physiology indexes of rice, the variation of soil moisture, the pest resistance and the lodge resistance, the change of soil temperature in paddy fields. the yield constitutive factors, the quality of rice and so on. in saline land. control irrigation and intermittent leaching modles were adopted to validate the adaptability of the technique in irrigation of rice in saline land, to analyze rice ' s physiological - ecological indexes and the change of soil salt content under the conditions of control irrigation leaching of rice and and to provide control irrigation and combined modle of intermittent leaching to adapt to different conditions

    本文從試驗及試驗資料入手，取得以下主要成果和結論：對鹽堿地水稻節水灌溉技術進行優化研究，系統地分析了不同節水灌溉技術對水稻生理指標及產量的影響，採用了多目標模糊優化的方法，對灌水技術進行綜合評判，優選了節水灌溉技術，論證該地區宜採用水稻控制灌溉技術；闡述控灌技術通過調節和控制水稻的需水規律，降低水稻高產情況下的無效水量消耗，從水稻生理、生態節水兩方面分析了控灌技術節水機理，針對性地總結出水稻各生育期實施節水控灌技術的步驟及技術要點；通過控灌與淹灌的定量對照比較，從根系、莖蘗、冠層葉片及綠葉動態到株高，土壤水分變化，抗病蟲害、抗倒伏能力，稻田土溫變化，產量構成因素及稻米品質等諸多方面進行動態比較，分析控灌技術高產優質機理；在鹽堿稻地採用控制灌溉+間歇淋洗模式，跟蹤測試田間水鹽變化狀況，驗證控制灌溉技術在鹽堿地區水稻灌溉中應用的適應性，通過分析水稻控制灌溉淋洗條件下水稻生理生態指標，提出優化控制灌溉+間歇淋洗組合模式，為進一步在高礦化度地區試驗水稻控灌技術奠定基礎。
  6. We select ni / cr alloy resistor as element together with ceramic embedding hearth ; select small flat - and - disc heat - even hubby ceramic sample holder, select ni / cr & ni / si thermoelectric couple ( type k ) as thermoscope with threads 0. 5 mm in diameter which is installed in the middle of the holders symmetrically ; select aluminum silicate fire - retardant fiber as materials for heat preservation ; design some hardware, for example temperature controller & transporter, signal amplifier etc ; design controlling curve to heat stove ; and introduce the method of least squares nonlinear regression and subsection function to deal with data. in order to obtain the reasonable operation conditions and operation curve, we have also done many theory analysis and experiment discussions

    通過理論和試驗探討，選用鎳鉻合金電阻絲作為加熱元件，配以陶瓷質埋入式爐膛；選用陶瓷質小尺寸扁平?圓盤均熱塊體型樣品支持器；選用0 . 5mm絲徑鎳鉻?鎳硅熱電偶（ k ）作為測溫元件；熱電偶對稱安置在樣品支持器容器的中部；選用硅酸鋁耐火纖維作保溫材料；合理選用和設計了溫度控制器、溫度變送器、信號放大電路等硬體；採用升溫曲線來控制爐膛供熱過程；採用最小二乘法非線性回歸與分段函數相結合的曲線模擬方法，進行圖形處理。
  7. It is found that the appropriate lowering of the chamber temperature of water gas producer and the thickness of coal bed is favorable to controlling the volume fraction of o2 and co in the recovered flue gas

    通過試驗與分析，發現適當降低水煤氣發生爐爐溫與煤層厚度，有利於控制回收煙氣中o2及co的體積分數。
  8. This y101d product is fitted for curing test, drying test and moisure content test and high temperature test. temperature is controlled by digital - display attemperation instrument

    Y101d本產品適用於烘培、乾燥、含水率測試，高溫試驗。由數顯溫控儀自動控制您所需要的溫度，是各行業必需的理想的設備。溫控范圍： 50 - 300攝氏度。
  9. Rules and process are established on inspecting and testing finished products, including the tests of durability, heat build - up and intermediate controlling

    建立成品檢驗和試驗規程，可進行輪胎耐久試驗，負載下升溫度試驗、中間材料控制試驗等。
  10. Thirdly, radiator performance test - bed thermal system control modeling and rule self - organizing fuzzy control simulation were studied. the water supply temperature, radiator inlet temperature, test room temperature based on water temperature regulation, air supply average temperature and test room temperature based on air temperature regulation total five controlled processes transfer function were set. finally, rule self - organizing fuzzy control simulation for two

    通過試驗，辨識了散熱器實驗臺熱工系統中供水溫度、散熱器進水溫度、基於熱水系統調節的測試室溫度、送風平均溫度及基於送風系統調節的測試室溫度共5個被控過程的傳遞函數，並對基於熱水系統調節和基於送風系統調節的測試室溫度響應過程進行了規則自組織模糊控制模擬。
  11. This method avoids the influence of resistances and cirumstance temperature, leading to escape from magnitude loss

    這種橡皮繩試驗速度控制方法克服了由於阻力、環境溫度等因素造成的影響，避免了造成巨大損失危險。
  12. However, the foundry plant of tsinghua university lacks old sand with high temperature and can not carry out test of cooling control

    但因清華大學鑄造廠缺乏溫度較高的舊砂，以致無法進行降溫控制效果的試驗。
  13. The sample with low emitter efficiency has completed as the method of above. this lead to the greatly decrease of the reverse recovery time and the low reverse leakage and forward voltage, especially the excellent temperature character of the leakage. the test date shows that the samples reach the first class of international level

    本論文作者通過模擬測試，驗證了課題研究的理論設想，並設計製作了具有低陽極發射效率結構的高壓功率frd ，利用局域鉑摻雜和電子輻照相結合的壽命控制方式，實現器件反向恢復時間的極大減小，並且反向漏電流、軟度因子、正向壓降等關鍵參數也較理想，且具有極佳的漏電溫度特性，達到器件綜合性能的優良折衷，達到國際先進水平。
  14. In the matter - in - loop simulation experiment of aero - engine control system, the turbine outlet temperature, which characteristics with high and quick change, is hard to be simulated

    航空發動機控制系統半物理模擬試驗中，渦輪出口氣體溫度高、變化快，難以模擬。
  15. It now possesses of not only some production equipment advanced in the national level, such as automatic hydraulic pressure spring eye machines, automatic control quenching furnaces and automatic control tempering furnaces the control accuracy attains 5 and shot blasting machines of landscape and vertical orientation, but also some sophisticated quality detection equipment, such as durometers, metallographic microscopes, stiffness and endurance test machines, etc. besides the hardware equipment, the company has a group of senior specialized technical personnel in the field of the design of the leaf spring processing, the leaf heat treatment as well as the tqc total quality control

    擁有自動液壓卷耳機自動控溫的淬火爐和回火爐爐溫控制精度達到5橫向和縱向噴丸機等國內先進的生產設備。同時還有為保證質量購置的硬度計金相顯微鏡剛度檢測及疲勞試驗機等先進的質量檢驗設備。從產品生產開始的每一個環節進行全方位的質量控制。
  16. Accelerated exposure of automotive interior trim materials using an outdoor glass variable angle controlled temperature apparatus

    使用戶外玻璃可變角度控制溫度設備加速汽車內部裝飾材料的加速暴露試驗
  17. The use of mcu makes the induction cooker intelligence, mainly offers good man - machine interface, power automatic control and temperature automatic control, time control as well as various automatic detections alarm etc. this system covers many fields such as electronics, mechanicals, magnetic, algorithms etc. mcu program structure divides into two parts as main program and timer interrupt service program, after many times " testing and running, the program runs steadily and reliably

    單片機的使用讓電磁爐實現了智能化，主要包括提供良好的人機界面、功率自動控制、溫度自動控制、定時控制以及各種自動檢測報警等。該系統覆蓋了電、機、磁、算等多個領域的知識。單片機程序結構分主程序和定時器中斷服務程序兩個部分，經過反復試驗運行，程序運行穩定可靠。
  18. Based on fuzzy control theory and the computer control technology of tdn - acs + experimental system, a computer control system of fuzzy technology was designed

    摘要以模糊控制理論為基礎， tdn - acs +計算機控制技術試驗系統為平臺，設計了一個基於模糊技術的計算機溫度控制系統。
  19. Currently most domestic break - test - plateform adopt the liquid - pressure - servo technique, which possesses the advantages of higher frequency - response and higher controlling exactness, but in the same time, the disadvantages of higher cost, variation of function with the change of oil viscousness produced by the fluctuation of temperature. moreover, the liquid - pressure system is sensitive to the pollution of oil, so it is necessary to take protective and filtrating steps

    目前，國內的制動器試驗臺大多採用的是液壓伺服控制，這種控制具有響應頻率高、控制精度高等優點，主要缺點是系統成本高、油液粘度隨溫度變化引起工作性能的變化、且液壓系統對油液的污染比較敏感，必須要有良好的保護和過濾措施。
  20. Aiming at drawbacks that environment simulate test laboratory ( estl ) ' s control precision is being dropped, the system digital simulation, the system characteristic analysis is proceeded ; basing on it, intelligence pid control processor, integral desaturation pid control processor, leading adjust control processor ( leading adjust of point of inflection of curve ) is planned, double loop control processors of low temperature system is consummated, so, the new control scheme and control program is formulated ; moreover through control program " simulate debugging and environment simulate test, 18 experimental curves and 19 experimental items is fulfilled totally. it proved that estl ' s control system and control program are successful. experimental result makes it known that the new control plan solves the problem of low control precision

    本論文針對環模室原控制系統存在的控制精度下降等問題，進行了系統模擬及環境模擬系統特性分析，在此基礎上，設計了智能pid控制器、抗積分飽和的控制器、預估補償控制器、完善了低溫系統的雙迴路控制，制定了新的控制方案和控製程序組態，並對其控製程序進行模擬調試及結合實際試驗對其控制系統進行驗證；共計完成了18條曲線， 19個項目的試驗，對其控制系統及控製程序進行了充分的考驗。
分享友人
分享到 Line

分享到臉書