控制閥數據單 的英文怎麼說

中文拼音 [kòngzhìfáshǔjùdān]
控制閥數據單 英文
industrial-process control valves : control valve data sheet
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 據 : 據Ⅰ動詞1 （占據） occupy; seize 2 （憑借; 依靠） rely on; depend on Ⅱ介詞（按照; 依據） according...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 數據 : data; record; information
  1. The second chapter simply introduces the development of alternate asynchronous inverter technology and retrospects some types of energy - saving systems for hydraulic elevators. then the working principles of the project are discussed and analyzed at four different working status, i. e. light load upwards, heavy load upwards, light load downwards and heavy load downwards. and the chapter focus on the introduction of structure design of pump station, calculation and type selection of pump / motor reversible units, research on oil leakage principles of accumulator circuit, design of accumulator - pump / motor pressure - energy transformer and integrated valve blocks, etc. the last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced

    論文第二章首先簡單介紹了交流異步電動機變頻調速技術的發展概況，在回顧電梯液壓控制系統節能技術的基礎上，介紹了本課題研製的「採用蓄能器的液壓電梯變頻節能控制系統研究」的基本原理，分析了動力系統在電梯轎廂輕載上下行、重載上下行等四種典型工況下的基本工作狀態和工作方式；詳細地介紹了本課題節能系統液壓動力泵站的結構設計和參數設計，重點研究了液壓動力泵站的結構設計、液壓泵馬達可逆性問題及其選型設計計算、蓄能器迴路泄漏油損失機理的研究及其補償裝置的設計、蓄能器-泵馬達壓力能量轉換裝置的設計、多功能集成控制閥組的設計等內容；最後簡單介紹了本課題矢量控制變頻控制櫃的外部附件電氣接線、計算機控制及數據採集系統的硬體設計等內容。
  2. Industrial - process control valves. part 7 : control valve data sheet

    工業過程式控制制閥第7部分:控制閥數據單
  3. According to the principle of lower cost, higher reliability, the design completes much work. the contents of project are as follows : ( 1 ) pic micro - controller which is lower - power and lower price is the core of control device. the whole circuit realizes the functions of collecting pulse, keeping data, driving electric machinery valve, reading and writing ic, detecting power supply, sound alarm and liquid crystal display

    設計依據低成本，高可靠性的原則完成了以下工作： （ 1 ）用功耗低、價格便宜的pic系列單片機作為控制裝置的核心，控制裝置的硬體電路實現了脈沖採集、數據存儲、電機閥驅動控制、 ic卡讀寫、電源檢測以及聲音報警和icd液晶顯示等功能。
  4. The project is funded by the anhui oil pump and oil nozzle factory. the aim of this project is to develop the automatic separation system of injector valve and orifice, based on the pneumatic sensor and the mcu

    本課題來源於安徽油泵油嘴廠，目的是研究一套價格為企業所接受的基於氣動傳感器並以單片機進行數據處理和控制的噴油嘴偶件針閥和針閥體自動測量分選系統。
  5. The objective of this dissertation is a kind of press - high speed numeric control oil - press. with a theoretical analysis and study about proportional control system, this paper sets up the mathematical model of proportional valve controlled non - symmetry hydraulic cylinder via the hydraulic system model building. then analyzes and modifies the model based on the matter of this study, and simulates the model with matlab software to confirm pid parameters, thus designs the pid controller

    本學位論文針對一具體的研究項目?高速數控壓機的開發，對比例控制系統進行理論分析與研究，通過對液壓系統的精確建模，建立起比例閥控非對稱液壓缸的數學模型，然後根據所研究問題的實際情況對模型進行必要的分析和修正，再運用模擬軟體matlab分析系統模型及確定pid控制參數，設計出pid控制器，使得控制系統的設計具有更多的可靠性和靈活性，最後運用pic單片機實現此控制，並結合整機調試試驗驗證了pid控制的成功。
分享友人
分享到 Line

分享到臉書