控制閥閥芯 的英文怎麼說

中文拼音 [kòngzhìxīn]
控制閥閥芯 英文
control valve trim
  • : 動詞1 (告發;控告) accuse; charge 2 (控制) control; dominate 3 (使容器口兒朝下 讓裏面的液體慢...
  • : Ⅰ動詞1 (製造) make; manufacture 2 (擬訂; 規定) draw up; establish 3 (用強力約束; 限定; 管束...
  • : 名詞1 (指在某方面有支配勢力的人物或家族) established house or power group; a powerful person or...
  • : 芯名詞1. (物體或器物的中心部分) core 2. (蛇的舌頭) snake's tongue
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Use zero water pressure opening of valve core without any medium pressure, suitable for the sewage - draining control system of pipelines, water tank etc. containers and the automatic water falling of a drinker. this valve can be fitted with another more than 60 kinds of valve casings, resulting in a flexible installation

    採用零水壓開啟,開啟無須介質的壓力,適用於管道水箱等其他容器的排污系統飲水機的自動下水等,該另有六十余種體與之匹配,安裝靈活。
  2. Then pid flow rate control algorithm is introduced. all experiments made in this chapter are about measuring the valve parameters according to spool positions, single actuator flow rate control by the calculated flow rate feedback control method, free flow rate dividing control under the sufficient pump discharge flow rate situation, proportion flow rate dividing and flow rate dividing based on meter - in flow rate feedback control method under insufficient pump discharge flow rate situation. the results of all experiments proved that the method presented in this thesis is an effective way to overcome the unreasonable flow rate dividing when simultaneously operating multi - actuators with different inertia loads

    第四章介紹了多執行器復合實驗系統和實驗方法;介紹了實驗採用的流量的pid演算法;並測定了執行器位移相關的系數;做了單個執行器計算流量反饋流量、流量足夠情況下多執行器流量任意分配、流量不足情況下多執行器按比例調節流量分配和多執行器進油側流量反饋分流實驗;通過實驗說明了論文提出的分流方法能實現大小慣性負載復合操作時的合理分流。
  3. Gunagzhou panyu rongxiang faucet co., ltd. was opened in 1998, the new factory locates in shiji town panyu district guangzhou city, the area is 1, 5000 square meters. it has more than 800 staff and 18 professional workshops now. they are founding workshop, forging workshop, punching workshop, cnc workshop, claming workshop, soldering workshop, polishing workshop, assembling workshop, mould workshop, polishing workshop, electroplated workshop, test workshop etc. we have the ability to work in pineline from casting, forging machining step to polishing and plating step

    廣州市番禺榮祥水暖器材有限公司創建於一九九八年,廠區位於廣州市番禺區石基鎮,佔地15000平方米,主要以生產陶瓷和水暖器材配件為主,現有員工八百多名,擁有鑄造車間(分為引鑄和砂鑄) 、鍛壓車間、沖壓車間、數車間、鉗工車間、焊接車間、拋光車間、彎管車間、模具車間、新產品試車間、電鍍車間、試驗車間、檢測車間、裝配車間等十八個專業車間,具備了從鑄造、鍛沖壓、機加工到外表層拋光電鍍一條龍的生產能力。
分享友人