控制電機 的英文怎麼說

中文拼音 [kòngzhìdiànjī]
控制電機 英文
cm
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 機 : machineengine
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 電機 : （任何產生和應用電能的機器 特指發電機、電動機） any power generating or power driven machine esp ...
  1. According to whether the light intension is in the zone of ccd linear response we control the direct current dynamo to drive the light filter to reduce the measure err effectively

    根據光強是否在ccd線性響應區間這一結果來控制電機帶動濾光片轉動，實現了對光強的自動調節，從而減小測量誤差。
  2. The circuit receives feedback signal of encoder, disposes it by pid and in the form of digit sends control signal which is transformed by d / a into analogue signal to servo amplifier, so further to control motors

    電路板接收碼盤反饋信號，通過內嵌的pid演算法，以數字形式給出控制量，經過d a轉化為模擬控制信號給伺服放大器，進而控制電機運行。
  3. Motor are widely used in industrial automation, office automation and household automation, most of which use electric power and computer control

    特別是在工業自動化、辦公自動化和家庭住宅自動化方面使用大量的控制電機，幾乎都採用電力電子器件進行微機控制。
  4. The control motors in the well traction robot require high temperature resistant, quick response, small volume and large power density. because coreless dc motors uses ironless - rotor, the inertia and inductance is very small, mechanical time constant is less than 28 milliseconds, several products can attain in less than 10 milliseconds. its weight and size are 1 / 3 - 1 / 3 less when compared with an iron core motor of same power

    水平井牽引機器人對控制電機不僅有耐高溫要求，而且有響應快、體積小、能量密度大等要求，而空心杯電樞直流電動機由於無鐵心，故慣量和電感均大為減小，機電時間常數小於28ms ，部分產品可以達到10ms以內;與同等功率的鐵芯電機相比，其重量、體積減輕1 / 3 - 1 / 2 ，是低慣量電機中性能最好的一種。
  5. Electrical machinery control technology

    電機學及控制電機
  6. We are specialized in manufacturing all kinds of series universal ac motor, pmdc motor, brushless dc motor, induction motor, shaded - pole motor, stepped motor, servo motor, controlled motor, flame - proof and submersible motor

    專業製造各類串激電機永磁直流電機無刷直流電機感應電機罩極電機輪箱電機步進電機伺服電機控制電機防爆及潛水泵電機。
  7. Electrotechnical terminology. control motors and feedback components

    電工術語控制電機
  8. Basic outline constructional type for control motors and feedback components

    控制電機基本外形結構型式
  9. Type designation for control motor

    控制電機型號命名方法
  10. Turn over and close board part : vfc motor, round pan reduction drive, frame and rocker

    翻板、合片部分：由變頻控制電機、原盤減速機、翻板支架及搖臂組成。
  11. Simulation results of the method for a three - level inverter feeding induction motor are presented

    根據不同的運行速度，選用不同的電壓空間矢量進行線性組合，控制電機的定子磁鏈和電磁轉矩。
  12. Then hardware for control is made of organizing layer for gait planning and executing layer for motor control, in which progression control can be conducted

    控制硬體分為進行步態規劃的組織層和控制電機的執行層，實現遞階分散式控制。
  13. The systems are composed of single - chip microcomputer and several kinds of interface circuits and control the voltage to run after the change of load

    該系統是由單片機和各種介面電路組成，控制電機的電壓跟蹤負載變化，達到節能的目的。
  14. Feeding and face fixing part : vfc motor, reduction drive, initiative, passivity drive roller. belt roller, face fixing, trimming and special width tape

    輸送整形部分：由變頻控制電機、減速機、主、被動傳動輥、調帶輥、整形、修邊及特種寬面膠帶組成。
  15. After we apply the design scheme of this paper to a three - phase asynchronous motor, the simulating experiment result indicates that the digital control system realizes the motor ' s stable running and fast response during the start - up and unexpected change in load ; moreover, it realizes the good dynamical performance

    將本文的設計方案應用到一臺實驗用三相異步電動機上，模擬實驗結果表明本文所設計的基於tms320f240dsp晶元的數字控制系統能夠控制電機穩定運行，啟動及負載突變時反應迅速，被試電機動態性能良好。
  16. The full automatic mechanical arm is built for letoff and wrap - up systems. the extruding quantities of each unit are controlled by frequency motor, the forming system adopts the synchronous group control. the digital displays are used for letoff, wrapup, extruding, drawing, line speed and meter recording

    放卷、收卷設置機械手全自動控制；各組擠出量由變頻器控制電機來完成，成型系統由一臺變頻器群控三臺成型牽引電機，與機械配合達到同步，該設備的放、收卷、擠出、牽引、線速、計米全部由數字化顯示。
  17. By means of building modelling with the target angular displacement and its sliding model variable structure controller of transmission ratio control electromotor, the parameters of entire controller are defined

    通過對速比控制電機目標角位移、角位移滑模變結構控制器的建模，來確定整個控制器的設計參數。
  18. The application of bp neural network to speed control system on usm is discussed, and a program is designed for training the bp neural network by matlab ’ s nntool, a three layers neural network of 2 - 8 - 1 is determined through simulation, then write the weights and biases of the nn into dsp to make on - line training, and it reaches the purpose of controlling usm ’ s speed

    利用matlab7 . 0中的神經網路工具箱進行結構設計和離線訓練，通過模擬實驗最終確定了2 - 8 - 1的三層網路結構，將訓練后得到的權值、閾值結果寫到dsp中，進行控制過程中給定速度的在線訓練，從而達到控制電機轉速的目的。
  19. Because it was trouble to control the heavy apron type feeder ' s rotate speed, the paper put forward a new method to achieve control the hydraulic motor speed efficiency by control electro motor rotate speed in transducer to control the hydraulic liquid flux of varable delivery pump

    摘要文章針對重型板式給礦機速度控制困難，提出了用變頻器控制電機轉速來控制變量泵液壓油流量，以實現對液壓馬達速度的調節方法。
  20. Being based on the steady state equations of the motor for the design of vsvf, vsvf can control the torque to a certain extent, but it can not implement the real control in the dynamic process

    轉差頻率控制能夠在一定程度上控制電機的轉矩，但它是以電機的穩態方程為基礎設計的，並不能真正控制動態過程中的轉矩。
分享友人
分享到 Line

分享到臉書