推力室噴管 的英文怎麼說

中文拼音 [tuīlìshìpēnguǎn]
推力室噴管 英文
thrust-chamber nozzle
  • 推 : 動詞1 （向外用力使物體移動） push; shove 2 （磨或碾） turn a mill or grindstone; grind 3 （剪或削...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 推力 : visatergo; soot; propulsive force; thrust; momentum thrust
  1. A three layers thruster was designed. the middle layer was chamber, the top layer was ignition circuit and the bottom layer contained a diaphragm with several nozzles. it could integrate 4 micro - thruster which diameter was 0. 8mm on the diaphragm with 10 * 10 * 2mm

    在實驗中，設計了三層的推力器結構，中間為藥室，上層和下層為點火電路和帶噴管的蓋片，可以在10 10mm和2mm厚的板上集成了4個直徑為0 . 8mm的微推力器。
  2. Abstract : this paper briefly presents th e application of advanced brazing techniques for a larye number of assemblies of space vehicles, such as thrust chamber and turbine rotor of launch rock et engine, titanium tube of satellite, attitude control engine injector and wave guide component of satell ite, reflector, tube and honeycomb panel of manned spacecraft, main engine nozzl e and preburner of space shuttle as well as the pipeline systems of space statio n

    文摘:簡略地介紹了先進釬焊技術在航天器部件，例如運載火箭發動機的推力室和渦輪轉子、人造衛星的鈦導管、姿控發動機噴注器和波導器件、載人飛船的反射器、導管和蜂窩壁板、航天飛機的主發動機噴管和預燃室以及空間站的管路系統等的廣泛應用情況。
  3. The experimental results indicates that the secondary mass flow increases with increasing of primary mass flow rate, but the bypass decrease because the primary mass flow rate increase more rapidly than secondary mass flow. the expansion configuration shows low thrust property due to low pressure in flow path. the secondary nozzle changes the pressure distribution in ejector combustor, and decreases bypass ratio, but obtain more completely mixing

    結果表明：二次流流量隨著一次流流量的增加而增加，由於二次流流量的增加速度低於一次流，引射系數減小；在純擴張式結構實驗中，引射燃燒室壓強很低，難以實驗推力增強；二次噴管改變了引射燃燒室的壓強分佈，降低了引射系數，改善了混合狀況能；對于本文的實驗結構，存在一個最優的二次噴管出口面積，使引射火箭推力最大，同數值模擬結果相吻合。
  4. Engineering drawing system can draw two dimension curve graphs, main detail drawing and assembly drawing. the curve of internal trajectory and dynamic simulation of particle external trajectory. the detail drawing includes the graph of chamber, grain design, connection body, nozzle, some standard part

    工程繪圖可以繪制二維曲線圖和零部件圖，其中二維曲線包括有內彈道壓（推）力?時間曲線、質點外彈道動態模擬曲線；零部件圖包括有標準螺栓與螺紋孔、燃燒室結構圖、裝藥設計截面圖、連接底結構圖、噴管結構圖及火箭發動機總體裝配圖。
  5. When liquid propellants are used the fuel and oxidize are fed under pressure to one or more combustion chambers and expanded to atmosphere through convergent-divergent nozzles.

    當使用液體推進劑時，在壓力作用下，燃料和氧化劑輸送到一個或幾個燃燒室中，並通過收斂-打散噴管，排到大氣中。
  6. The results indicate that with decrease of exit area of secondary nozzle, the bypass ratio is decreasing, and the static pressure in integrated ejector combustor is increasing, and mixing condition becomes better. there exists an optimal exit area of secondary nozzle to get maximum thrust of rocket ejector

    結果表明：引射能力隨著二次噴管出口面積的減小而減小；整體式引射燃燒室壓強隨著二次噴管出口面積的減小而上升，混合隨之更為充分；存在一個最優的二次噴管出口面積，使發動機推力最大。
分享友人
分享到 Line

分享到臉書