推力曲線測試 的英文怎麼說

中文拼音 [tuīlìqūxiàncèshì]
推力曲線測試 英文
measurement of thrust curve
  • 推 : 動詞1 （向外用力使物體移動） push; shove 2 （磨或碾） turn a mill or grindstone; grind 3 （剪或削...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 推力 : visatergo; soot; propulsive force; thrust; momentum thrust
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  • 測試 : test; testing; checkout; measurement
  1. The experiment procedure and analysis result about exteriorly extended end - plate connection with high strength bolt are introduced primarily ; each sample ' s dimension is given. the adding load equipment, measuring apparatus placed, measuring point established is detailed. adding load measure load and m - curve is produced ; the single span gabled frames horizontal displacement formula is deduced when the horizontal concentrated force is applied to it

    重點介紹了外伸端板高強螺栓連接的實驗過程及實驗分析結果，介紹了各組試件的形狀尺寸、加載裝置、測量儀器安放、測點的布置等；給出加載方式及測出的m -曲線；計算出試驗節點的初始剛度；推導水平集中力作用下單跨門式剛架考慮節點半剛性的側移計算公式。
  2. These stud " can be concluded as following : on the basis of the bhw - 35 steel p - s - n curve and its da ' dn growth law the method of low - cycle fatigue life evaluation of 401 t / h boiler was proposed. and a mechanics model was suggested for calculating the stress of internal pressure suffering elbow. with the elbow fatigue test, a method of evaluation the fatigue growth life of pressure suffering elbow is recommended ; and the elementary use of damage mechanics on the fatigue life evaluation of the boiler drum

    本文創新點為：在bhw - 35鋼的p ? s ? n曲線及da / dn擴展規律的試驗研究基礎上，提出了410t / h鍋爐汽包的低周疲勞壽命分析與預測方法；建立了一種橢圓截面變厚度彎管承受內壓時的應力計算力學模型，通過壓力彎管的疲勞試驗，本文推薦其低周疲勞擴展壽命預測方法；將損傷力學應用到鍋爐汽包疲勞壽命預測做了初步的探索。
  3. Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors

    諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3
  4. In all these 20 specimens, the embedded electronic steel - concrete slip transfer were respectively embedded on the steel shape webs and inside and outside of the flanges at certain intervals along the embedment length to measure the distributions of the interior slip, and the electronic strain gauges were also installed on the shallow grooves of each steel shape web and flanges at close intervals along the length to measure the distributions of the steel shape web and flanges strain, from which the distributions of bond stress were obtained. with these methods of measuring the distributions of slip and bond stresses, the establishment of the bond - slip constitutive relations were ensured

    用力的平衡方程，得到推出試驗中型鋼混凝土粘結應力的大小及其分佈規律;根據鋼一混凝土電子滑移傳感器的滑移量測結果，分析了沿型鋼埋置長度的內部滑移分佈規律，並對試驗量測的特徵滑移值進行了統計回歸;根據粘結應力和內部滑移測量結果，得出沿型鋼埋置長度方向上各截面的局部粘結應力一滑移關系曲線，建立了局部粘結滑移本構模型嘆x ）一s仁， ， … ， c ， … c 。
分享友人
分享到 Line

分享到臉書