摩擦圓盤 的英文怎麼說
中文拼音 [mócāyuánpán]
摩擦圓盤
英文
friction disc-
Disc friction clutch
圓盤摩擦離合器Squeeze flow between two parallel disks is considered for small gaps for rigid - plastic material with partial wall slip. firstly, the coulombic friction condition is discussed, and a new pressure distribution is obtained
首先對現有的庫侖摩擦條件下的壓力規律做了進一步的研究,找到了一種更合理的圓盤上的壓力分佈規律。Moreover, based on the assumption that the slip velocity at the disks increases linearly with the radius up to the rim slip velocity, another pressure distribution is derived by introducing a appropriate velocity field. then these different results by the different friction conditions and technique are compared. 2
同時,在圓盤邊緣處滑移速度一定,介質的滑移速度隨著半徑線性變化的假設下,引入合理的速度場,得到了另一種圓盤上的壓力分佈規律,並對不同的摩擦條件及用不同方法計算得到的結果進行了對比。Application of disk friction pump in axis seal
圓盤摩擦泵在軸封中的應用Loading capacity analysis of multiple - disk clutches in the consideration of error of axial force
考慮軸向力損失的多圓盤摩擦離合器的工作能力分析First super - low specific - speed centrifugal pump has a long and narrow flow passage for its high head and low capacity, and the power absorbed by disc friction is too high, so the efficiency is very low ; secondly the diffusion of flow passage is so high, that the reserved flow often emerges at the inlet and outlet of impeller. therefore the h ~ q characteristic curve is often hump - shaped, and at the low - capacity operating condition the instability often occurs ; thirdly the centrifugal pump at high - capacity operating condition is easy to overload because the n ~ q curve appears a rising trend
首先由於它的揚程較高、流量較小,所以它的流道狹長,圓盤摩擦損失較大,效率相對較低;其次由於它的流道擴散較嚴重,易在葉片進口產生迴流和在出口產生脫流,揚程流量特性曲線易出現駝峰,在小流量工況下易產生不穩定現象;第三,由於其功率流量曲線呈現上升趨勢,在大流量區運行時電機易過載。In this paper, a rub disc movement decomposition organization is firstly analyzed and proved to be a nonholonomic system. in fact, it is a speed changing mechanism the radio of which is variable
本文分析了一種摩擦圓盤傳動機構的運動原理,證明了該結構的為非完整機構的條件,並總結出該結構的實際上為我們可以認為非完整傳動機構實質上就是一種變傳動的變速機構。The efficient conversion of mass into energy by friction in the accretion disk of a black hole seems to be the only explanation for the copious amounts of energy generated by such objects
在黑洞增大圓盤片靠摩擦質量有效轉化為能量好像只能解釋靠這樣的物體產生的大量能量。Friction between adjacent zones of the disk causes it to become extremely hot and emit large amounts of x - rays
圓盤鄰近地方的摩擦導致它變得十分熱和發射大量x射線。After the topological structure of machine system and the method of conversion of coordinate are introduced, 3d model of the manipulator had been set up in pro / e. in the process, several problems had been solved, such as simplification of part model, assembly, idealization of rub disc movement decomposition organization
在介紹了軟體中機械繫統的拓撲結構和坐標變換的方法后,在pro e中建立了機械手的3d模型;解決了模型建立過程中的零件模型的簡化、零件的裝配、摩擦圓盤機構的理想化、模型中電動機的轉動方向等問題。分享友人