撓度測量 的英文怎麼說

中文拼音 [náodùcèliáng]
撓度測量 英文
deflection survey
  • 撓 : 動詞1. （輕輕地抓） scratch 2. （擾亂;阻止） hinder 3. （彎曲,比喻屈服）yield;flinch:不屈不撓indomitable; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 測量 : measure; survey; gauge; meter; measurement; measuring; surveying; mensuration; metering; gauging;...
  1. The instrument has two ball contact tips which have different diameters. its prominent merit is that it can find the minimum value of the thickness easily and output it directly. and also it has a splaying and closing control part for the tips to avoid destroying the surfaces of joints

    本測量裝置採用直徑不同的兩個球形觸頭直接測量撓性接頭細頸厚度，並能夠尋找細頸厚度最小值;同時該裝置含有的測頭球張合控制部分能夠避免接觸時劃傷工件。
  2. One thick necks ’ thickness measuring instrument with high precise and high efficiency is researched in this dissertation. one special flexible hinge gauge head is designed, differential solenoid inductance displacement sensor is chosen and modern micro - processing technology is used to meet the demand of measuring accuracy

    本文通過設計一種專用柔性鉸鏈測頭，採用差動式螺管型電感位移傳感器並結合現代微處理技術，對撓性接頭細頸厚度的高精度高效率測量裝置進行了研究。
  3. Test method for measuring warpage of ceramic tile

    測量瓷磚撓曲度的試驗方法
  4. Road testing. measurement of a rolling load deflection. part 7 : determination of deflection and curvature values using curviameter

    路面試驗.滾動加載撓度測量.第7部分:用曲率計測定撓度和曲度值
  5. This article discuss the method to measure distortion of truss by means of ccd device. the distortion can be measured with many kind of displacement transducer, but it must be placed on stable base. when the huge truss is moving through some tunnel, it is difficult to find a stable base, especially there is no enough space for someone to operate. it is hardly to measure the distortion by touching. on the contrary, this can be achieved by means of ccd device

    桁架在自重或載荷的作用下產生的撓度可以用多種位移傳感器測得，這些測量方法需要有良好的基礎，在大型桁架梁測量現場，由於桁架的變形，難于找到這種基準，如果加上測量環境惡劣，人無法操作情況，則會給撓度測量帶來極大的困難，而採用光電荷耦合器件，並利用激光進行遠程實時撓度測量，即可以解決這個難題。
  6. It " s function is to receive laser signal and to sent out the electric signal ; the second is the monolithic processor system. this part function is to pick up the electric signal sent by ccd detector and to compute the digital signal to get the data where the laser beamed, then sent the data to pc computer ; the third part is the control interface for people to control whole measurement process

    本文介紹的桁架梁撓度實時檢測的電荷耦合（ ccd ）測量系統由ccd接收系統，單片機測量系統和pc機測量軟體三部分組成。該系統採用線陣ccd為傳感器，以8031為控制核心，在單片機系統和pc機軟體之間建立了可靠的通信，能在比較惡劣的條件下獲取、顯示、存儲、處理和比較桁架的撓度值。
  7. Method for measurement of static deflection of power presses

    機動壓力機的靜載撓度的測量方法
  8. Because the plastic optic fiber ( pof ) have many advantage in short distance communication, such as fine flexibility, connect easy, cost low and so on. in the field of sensing, compared with the silicca optical fiber ( sof ), the pofs have high sensitivity, the range of measurement is big. so the plastic optical fiber more and more is valued by people, it has the quite considerable potential market and the application prospect

    由於塑料光纖（ pof ）在短距離通信中所顯示出來的可撓性好、對接容易、成本低等優勢及其在傳感領域較石英光纖（ sof ）有靈敏度高、動態測量范圍大等優點，塑料光纖越來越受到人們的重視，具有相當可觀的潛在市場和應用前景。
  9. At first, development of various cracks carefully recorded and strains on both the rebars and the stirrups were measured in detail, together with the deflections of the beam. in such a way, correlation between the measured strain profiles of the reinforcement and the observed cracking development of each specimen was pursued. principal factors contributing to the cracking pattern and failure mode were figured out as a result

    首先，通過單調靜力加載試驗研究，對梁的裂縫延伸和開展、縱筋應變、箍筋應變、梁的撓度等指標進行了細致的量測，試圖追蹤每一試件在裂縫發展及破壞過程中縱筋應變狀態的變化和裂縫發展程度的相關性，進而總結出有腹筋約束梁裂縫開展及鋼筋應力分佈的一般規律。
  10. Standard practices for making heatseals for determination of heatsealability of flexible webs as measured by seal strength

    通過測量密封強度測定撓性網熱密封性能用熔焊的標準實施規范
  11. In order to ascertain the real stress and deflection of structure this paper puts forward experimental scheme. by measuring data during the process of construction, we can know the distribution of stress in simply supported - continuous beam and compare with initial design, then we can adjust it by control method to ensure quality of the bridge

    提出具體的試驗方案，論述了測試元件的測試原理，通過測量各控制點在不同階段的應變和撓度，確定橋梁結構的實際應力大小和變形狀態，了解簡支轉預應力連續結構各跨主梁與連續處的應力分佈情況，並與設計相互驗證，通過施工控制使結構符合設計要求，保證施工質量。
  12. The paper made up a flexural experiment with six pieces of composite slab. during the every step of load exerted, the paper recorded the strain of cold - form steel deck and concrete, deflection, crack, slide, ultimate bearing capacity. by changing the thickness of cold - form deck, thickness and strength of concrete, amount of steel stud and other parameters, the paper discussed the behavior of loaded composite - slab

    本文進行6塊組合板的抗彎性能試驗，測試各級荷載下壓型鋼板及砼應變、組合板撓度、裂縫、板端滑移、組合板抗彎極限承載力；通過壓型鋼板厚度、砼板厚度、砼強度等級、栓釘數量等幾個參數的變化，探討組合板在荷載作用下的內力、變形情況。
  13. ( 2 ). discuss the factors which cause the bridge ' s deflection and pay more attention on the effect of the variry of cable ' s temperature on the bridge ' s deflection. then to bring forward the need of deflection measurement of the dafosi bridge of changjiang river

    討論了引起大跨度橋梁撓度變形的各種因素，並且著重討論了斜拉索溫度變化引起的橋梁撓度變形，繼而提出了大佛寺長江大橋撓度測量要求。
  14. Roof support elevation, the axis displacement and cross - deflection, the measurement made by the record

    屋架支座的標高、軸線位移、跨中撓度，經測量做出記錄。
  15. ( 3 ). put forward two structure scheme of opto - electronic deflection measurement sensor, light transmitting with non - mechanical scanning and light reflecting with non - mechanical scanning after compared exisiting methods of liquid level measurement to satify this needafter the comparison, an opto - electronic deflection measurement sensor based on light reflecting with non - mechanical scanning be confirmed. then the concrete design is to carry out, which includes the design of reflective surface, the design of pds ( photo detective subassembly ) ' s bracket, the design of floater and the design of shaking - absorbed accessory. during the process, there are a series of caculations and emulations. at last, the opto - electronic deflection measurement sensor has been designed and produced

    比較了現有液位測量方法后提出了能夠滿足大佛寺長江大橋撓度測量要求的基於連通管的光電撓度計的非機械掃描光透射式和非機械掃描光反射式的兩種方案，通過比較確定了非機械掃描光反射式方案。隨后通過對該方案進行具體的零件設計，主要包括反射面的設計， pds （光電接收組件）支架的設計，浮子的設計以及減震零件的設計等等，在設計的過程中包含了一些理論計算和模擬，最終設計和製作了光電撓度計。
  16. To our satisfaction, all the measuring results from the measurement locale are accurate and convincing comppared with the results calculated by the theory which makes it clear that the system can meet the demands of measuring upon the dafosi bridge of changjiang river. the system has achieved the long - time and real - time automatic deflection measurement of the bridge at first time in our country, and the system has passed the appraisal of the experts consigned by the ministry of communications so the system has the practical value on the long - span bridge ' s deflection measurement

    通過對橋梁實際測量結果與理論計算的結果的對比分析可知，本文所設計的連通管式光電撓度測量系統測量數據準確，系統可靠，能夠滿足大佛寺長江大橋撓度測量的需要。該撓度測量系統首次在國內實現了橋梁主梁撓度的長期實時自動監測，並且已經通過了交通部的項目驗收，具有一定的推廣價值
  17. Testing of resin and polymer cement compositions for use in construction - method for measurement of temperature of deflection under a bending stress

    建築用合成樹脂膠料試驗.第10部分:撓曲應力作用下反射溫度測量方法
  18. Tests relating to pavements. measurement of a rolling load deflection. part 2 : determination of deflection and curvature values using modified behkelman beam

    路面試驗.滾動加載撓度測量.第2部分:用改進的貝克曼量儀測定撓度和曲率值
  19. The measurement of deflection of a bridge is crucial constituent part in the monitoring of bridges. the majority of existing methods about bridge deflection measurement can not accomplish the real - time and long - range measurement. the ultrasonic method based on connected pipes still has shortage in precision and speed of measurement. to satify the need of deflection measurement of the dafosi bridge of changjiang river, an opto - electronic measurement method is to be used to improve on the method based on connected pipes. furthermore, we will design an automatic opto - electronic deflection measurement system based on connected pipes which can be practised in the long - span bridge

    大型橋梁的安全監測具有重要的現實意義，而撓度監測是橋梁監測的一個重要的組成部分。目前現有的許多撓度測量方法還不能實現實時遠程監測，已有的連通管式超聲波法還存在著精度較低，測速慢等不足。針對大佛寺長江大橋撓度測量的需要，在此採用精度較高的光電測量方法結合連通管的優點加以改進。
  20. The thesis refers to several facets below, ( 1 ). discuss important meaning of the deflection monitoring of the dafosi bridge of changjiang river and introduce the principle of existing deflection measurement methods of bridge so far. through comparison and analysis, bring forward the research content based on the connected pipes methods

    簡要闡述了大佛寺長江大橋撓度監測的重要意義，簡單介紹了國內外現有的撓度測量方法的原理，通過比較分析，在連通管測量方法的基礎上提出本文研究的內容。
分享友人
分享到 Line

分享到臉書