擠準模 的英文怎麼說
中文拼音 [jǐzhǔnmó]
擠準模
英文
die sizing-
Standard specification for ethyl cellulose molding and extrusion compounds
乙基纖維模製和擠壓化合物的標準規范Standard classification system for e - ctfe - fluoroplastic molding, extrusion, and coating materials
E - ctfe -氟塑料模壓擠壓和塗覆材料的標準分類系統Standard classification system for polyamide - imide molding and extrusion materials
聚酰胺-酰亞胺模塑和擠壓材料的標準分類體系Standard specification for cellulose acetate butyrate molding and extrusion compounds
乙酸丁酸纖維素模製與擠制化合物的標準規范During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied
在溫度場的模擬中,模擬結果表明,保壓時間是影響製件成形質量的關鍵因素之一,擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大,需進行參數之間的協調,只有當變形區內部始終維持準固態時,才能實現穩定的液-固擠壓成形過程;在變形場的模擬中,根據液態浸滲擠壓的成形特徵,選用了雙曲正弦剛-粘塑性有限元計算模型,研究了變形過程中應力應變場的變化規律,研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。Standard classification system for acrylonitrile - styrene - acrylate and acrylonitrile - epdm - styrene plastics and alloys molding and extrusion materials
丙烯氰-苯乙烯-丙烯酸鹽和丙烯氰- epdm -苯乙烯塑料和合金模製和擠壓材料的標準分類系統Standard classification system for thermoplastic elastomer - ether - ester molding and extrusion materials
熱塑性彈性醚酯模塑和擠制材料的標準分類體系This thesis presents systematic quasi - static and dynamic experimental researches on the engraving process of two pistons in solo soldier multi - purpose weapon system dzj00. on the basis of the analysis to the experimental data, a theoretical study is performed and a computing model is established. the calculating results fit well with the test results. at the same time, many affective factors have been considered
本文對單兵多用途攻堅彈武器系統內的活塞對制動環的擠進過程進行了系統的準靜態和動態試驗研究,在通過對試驗結果的分析的基礎上,對擠進過程從理論方面進行了一些探索性的研究工作,建立了計算模型並進行了計算,其結果和試驗結果吻合較好,同時分析了多種因素對擠進過程的影響。Standard practice for injection molding test specimens of thermoplastic molding and extrusion materials
熱模塑和擠塑材料的噴射模塑法試樣標準規程Standard specification for cellulose acetate propionate molding and extrusion compounds
纖維素醋酸酯丙酸酯模製和擠制化合物的標準規范Using engineering method and upper - bound method, this dissertation deduced a calculation formula for the load of powder radial extrusion
利用文獻提供的屈服準則和力學模型,運用工程法和上限法得出了具有工程意義的粉末擠壓擠壓力計算公式。Based on the research about state of metal in groove, an new five zone describing model for continuous extrusion process was established to describe the process, and its analytic solution of stress calculation for each sub - zone was given
摘要在連續擠壓技術研究的基礎上,通過觀測擠壓輪槽金屬的變形形貌,提出了「五分區」的連續擠壓變形過程描述模型,構成了連續擠壓輪溝槽變形區系統、完整、準確的表徵。Standard specification for cellulose acetate molding and extrusion compounds
乙酸纖維素模製和擠制化合物的標準規范Standard specification for polyethylene plastics molding and extrusion materials
聚乙烯塑料模塑和擠制材料的標準規范Standard classification for recycled post - consumer polyethylene film sources for molding and extrusion materials
模塑和擠制材料用再生聚乙烯薄膜原料的標準分類Standard specification for extruded and compression molded shapes made from poly vinylidene fluoride
由聚偏氟乙烯製成的擠制和壓模製型材的標準規范Thanks the solution to accurate controlling and compelte stabilizing of the extrusion process by employing the melt measuring gear pump
基於在塑料擠出行業中多年積累的實際經驗,精誠模具為解決這些問題,採用融體計量齒輪泵,使系統得到準確的控制和擠出過程中的完全穩定。Standard specification for extruded and compression molded rod and heavy - walled tubing made from polytetrafluoroethylene
聚四氟乙烯制擠壓和壓縮模塑桿和厚壁管的標準規范Standard classification system for styrenic thermoplastic elastomer injection molding and extrusion materials
苯乙烯熱塑性彈性體注模料和擠壓料的標準分類系統Standard specification for ultra - high - molecular - weight polyethylene molding and extrusion materials
超高分子量聚乙烯模壓和擠壓材料的標準規范分享友人