擰接 的英文怎麼說

中文拼音 [nǐngjiē]
擰接 英文
screw together
  • 擰 : 擰形容詞[方言] （倔強） pigheaded; stubborn
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  1. Loosen the adjustment screw, and adjust the length of the link rod

    請擰松調整螺絲，拔出或插入連接桿進行調整。
  2. Tighten the n coupling nut on the ac servo motor side temporarily

    臨時擰緊馬達邊的n型連接螺母
  3. The shark was threaded into a pipe "t" connection.

    一個螺栓體被擰進一個「T」形管接頭中。
  4. Cable connections are made to the side of the battery by means of threaded bolts into "cast-in-lead" stainless steel nuts.

    在蓄電池一側，利用螺栓擰到「鑲鑄鋁」的不銹鋼螺帽上進行饋線連接。
  5. Using the optimum calculating method, some important technical parameters could be determined, that is, optimum supporting force, allowable deformation of rock mass, cross section area of u - shape set, pre - tight force and diameter of the bolt as well as torque to provide optimum supporting force

    用這一計算方法能求出巖石恆阻支護的重要技術參數，即最優（小）恆阻支護力、圍巖最大允許變形量、恆阻u型鋼支架的截面積、聯接螺栓的預緊力和直徑及最優支護力的擰緊力矩。
  6. In the joint of lg pex - a pipe, male xocket is pressed to a convex on the inserting part and the fastening ring will contract to fasten up the heating pipe by the fastening of outer nut, and there is also a convex on the ring to offer close coupling by mechanical re - press effect to prevent water from leaking in case of heat expansion

    在lg地熱管中的連接部位不僅閥門管套插入部分的凸起部位被機械作用壓密，而且隨著外部螺母被擰緊，使緊固環收縮，從而帶緊熱炕暖氣管，另外由於存在凸起部位，可通過機械作用進行再次壓密，因此可防止由於熱膨脹而引起漏水。
  7. Tighten the n coupling nut on the ball screw side

    擰緊絲桿邊的n型連接螺母
  8. Union, screwed - onto, titianium alloy, flared tube

    鈦合金擴口式擰入式直通管接頭
  9. The cords of all link back, strandentwining cable of all flesh. that is why mystic monks

    所有臍帶都是祖祖輩輩相連接的，蕓蕓眾生擰成一股肉纜，所以那些秘教僧侶們都是。
  10. Then, a twisted grey garter looped round a stocking : rumpled, shiny sole

    接著是一隻歪歪擰擰地套在長襪上的灰色襪帶。
  11. Reducer, screwed - onto, 90 degree elbow, titianium alloy, flared tube

    鈦合金擴口式擰入式變徑直角管接頭
  12. Elbow, screwed - onto, 45 degree, titianium alloy, flared tube

    鈦合金擴口式擰入式彎管接頭
  13. Elbow, screwed - onto, 90 degree titianium alloy, flared tube

    鈦合金擴口式擰入式直角管接頭
  14. Tee, screwed - onto, titianium alloy, flared tube

    鈦合金擴口式擰入式三通管接頭
  15. Tee, screwed - onto, asymmetry, flared tube

    擴口式不對稱擰入式三通管接頭
  16. Elbow, screwed - onto, 90 degree, flared tube

    擴口式擰入式直角管接頭
  17. Elbow, screwed - onto, 45 degree, flared tube

    擴口式擰入式彎管接頭
  18. Cross, screwed - onto, flared tube

    擴口式擰入式四通管接頭
  19. The screw - shell of plug - fuse type fuseholders and the contact of a post - extractor fuseholder adjacent to the mounting surface ( unless the post - extractor fuseholder is of deadfront construction ) shall be connected to the load side of the circuit

    臨近盤面安裝的插拔式保險管座的擰動式外殼和柱狀拔出式保險管座的接頭應該接到電路的負荷端上
  20. Swiftly wringed tie - in with nut

    帶管接螺母的快擰接頭
分享友人
分享到 Line

分享到臉書