擰松 的英文怎麼說

中文拼音 [nǐngsōng]
擰松 英文
back-out; screw off; unscrew
  • 擰 : 擰形容詞[方言] （倔強） pigheaded; stubborn
  • 松 : Ⅰ名詞1 （松樹） pine 2 （絨狀或碎末狀食品） dried meat floss; dried minced meat 3 （姓氏） a surn...
  1. Unscrew the bonnet by turning counterclockwise

    反時針方向旋轉擰松閥蓋。
  2. 1, screw down the flange bolt regularly and the tightness of all bolts shall be same as soon as possible. under bad conditions, flat pad as well as spring gadket shall be installed to prevent the nut loosening

    1法蘭螺栓應逐步均勻地加壓擰緊，所有螺栓松緊度盡可能一致。使用條件惡劣的場合，除加平墊外可添加彈簧墊圈，以防螺母松動。
  3. Loosen the adjustment screw, and adjust the length of the link rod

    請擰松調整螺絲，拔出或插入連接桿進行調整。
  4. Tighten locknut 1 to fix the thread stand

    擰緊固定螺母1不讓線架裝置松動。
  5. To make the tilt front - up, loosen the set screw, insert a screwdriver into the feed bar shaft, and turn it by 90 in the direction of arrow mark

    想要向前上方傾斜時，請擰松固定螺絲，把螺絲刀插進送布臺軸，朝箭頭方向轉動90 。
  6. Loosen setscrews 2 in the vertical driving cam

    擰松上下傳送凸輪的固定螺絲2 。
  7. Loosen setscrew 1 in the oil shield plate, and remove oil shield plate 2

    請擰松防油板固定螺絲1 ，然後卸下防油板2 。
  8. Unscrew the four bolts to separate the body from the bonnet and control group

    擰松四個螺栓，從閥帽和控制組建之間分開閥體。
  9. Remove the throat plate, loosen hook screw 6 and adjust the hook

    調整旋梭時，請卸下針板，擰松旋梭固定螺絲6 ，然後進行調整。
  10. To loosen a bolt

    擰松螺栓
  11. To looser a bolt

    擰松螺栓
  12. Gear operator is removed by unscrewing hex head screws which hold operator to valve body

    通過擰松將操作機構固定在閥體上的六角螺栓來拆卸齒輪操作機構。
  13. Loosen needle clamping screw 2, and hold needle 1 so that long groove a in needle 1 faces exactly to the left

    擰松機針固定螺絲2 ，把機針1的長槽a轉到橫向朝左。
  14. Brown first attempted to pry loose the ceiling rod and red gemstone, but neither would budge

    布朗首先嘗試弄明白如何擰松天花板的金屬竿和竿上經過雕琢的紅色寶石，但是皆不能擰動。
  15. Maximize the stitch length, and turn the handwheel until walking foot 1 reaches its front end position. now, loosen screw 2 in the center shaft bell crank

    把縫跡調到最大，轉動飛輪，在外壓腳1前進到最前的位置擰松中軸輪緊固螺絲2 。
  16. Standard specification for " twist off " type tension control structural bolt nut washer assemblies, steel, heat treated, 120 105 ksi minimum tensile strength

    120 105ksi最小抗張強度的熱處理鋼制"擰松式"張力控制結構螺栓螺母墊圈配件的標準規范
  17. While unscrewing the injector button head, a second wrench must be used to assure that the injector body is not loosened from the main valve

    在擰松注入器圓頭螺栓時，要用第二個扳手固定住注入器，防止其從主閥門上松落下來。
  18. Actuator mounting bracket on automated valves is removed by unscrewing hex head screws which hold bracket to valve body

    通過擰松將固定支架固定在閥體上的六角螺栓來拆卸電動或氣動閥門的執行機構安裝支架。
  19. One thing to take into consideration when looking at a previously owned knife is that the former owner may have loosened the pivot screw so they could " sling " the blade open, thus compromising the makers original " specs " for blade play

    對購買二手刀來說，一個要考慮的因素是，前擁有者可能為了用「甩」法開合刀體而擰松刀軸螺絲，這會影響制刀者對該刀的設計初衷。
  20. The injector button head must be unscrewed one half turn to open the internal valve before injecting grease

    在注入潤滑油之前，注入器圓頭螺栓必須擰松半圈，打開閥門內部部件通道。
分享友人
分享到 Line

分享到臉書