支撐夾 的英文怎麼說

中文拼音 [zhīchēngjiā]
支撐夾 英文
halteklammer retainer clip
  • 支 : Ⅰ名詞1 （分支; 支派） branch; offshoot 2 （地支） the twelve earthly branches3 （姓氏） a surname...
  • 撐 : Ⅰ動詞1 （抵住; 托住） prop up; support 2 （用篙使船行進） push or move with a pole 3 （支持） mai...
  • 夾 : 夾構詞成分。
  • 支撐 : 1 （抵抗住壓力） prop up; sustain; support 2 （勉強維持） support; prop up3 [建築] strut; brace; ...
  1. In fh2 the hand - held mg34 can only be used when laying flat on the ground, using the bipod for support

    在fh2中，手持的mg34隻有趴在水平地面上並用雙腳夾支撐時才可使用。
  2. Through comprehensive analysis of the tbph, the relationship between the induction heater site and rotary axis and the relationship between the support wheel and initial site of the front clapper have been concluded. the minimum nominal curvature radius has also been determined

    通過對加熱彎管成形的綜合分析，得出感應加熱器與回轉中心的位置關系及支撐輪與前夾頭初始位置關系，並確定了加熱彎管最小名義彎曲半徑。
  3. This paper applies nonlinear finite element program bsnfem to analyze the behaviors of eccentrically braced steel frames under cyclic load. the study that comprehensive and systematic analyze the factor of links length, thickness of links flange, distance of links rib, thickness of links rib and angle of brace to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel frames have been some studied before. this paper fills the black in the filed factor of high - span ratio, brace stiffness and brace - to - beam connections to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel trames and any factor to be changed affect energy - dissipation capacity of y shape eccentrically braced steel frames

    對耗能梁段的長度、耗能梁段腹板的厚度、耗能梁段翼緣的厚度、耗能梁段加勁肋的間距、耗能梁段加勁肋的厚度、支撐的夾角等因素的改變對d形、 k形偏心支撐鋼框架耗能的影響，前人已有一些研究，本文對這些因素的影響進行了全面系統的分析，完善了理論分析的不足；而結構高跨比、支撐剛度、支撐與梁的連接形式等因素對d形、 k形偏心支撐鋼框架破壞機理的研究以及各種因素對y形偏心支撐鋼框架破壞機理的影響，則很少有人涉及，本文對此也進行了深入系統的分析，填補了這一研究空白。
  4. The slurry is pumped under pressure into a vessel that is fitted with a stack of vertical leaves that serve as filter elements

    過濾機葉片外表層用特殊結構的細濾網精製而成，中間夾有支撐網，過濾精度高
  5. When escape system is activated, the grille wings at the upper fairing will open, supporting frame will pick up the orbit and returning modules, the lock between the returning and propelling modules will release, the lock between the upper and lower fairings will release, escape rocket will be ignited and finally pull the escape flight vehicle away from the rocket

    該系統由逃逸塔和上部整流罩組成，逃逸系統加上飛船的軌道艙和返回艙構成逃逸飛行器。當需要逃逸時，上部整流罩上的柵格翼打開，支撐機構夾住飛船軌道艙和返回艙，然後返回艙與推進艙解鎖上下整流罩解鎖逃逸發動機點火，逃逸飛行器飛離運載火箭。
  6. Tabular layouts of article characteristics for clamping saddles for supporting and guarding tubes

    支撐管和保護管用的鞍座夾產品特性圖表
  7. Leading by the nc bend tube welding jig design flow, develop a series of tools in the cad software platform, then construct the nc bend tube welding jig cad system under the tools collection ; 2 ) use the reverse technology of nc bend tube ’ s modeling, aim to the most general nc bend tube, reevaluation the bend tube ’ s essential feature by using the vector transformation algorithm, and establish bend tube model above this foundation

    論文的主要工作包括以下幾個方面: 1 ）提出了數控導管焊接夾具cad系統框架。在數控導管焊接夾具的設計流程引導下，于cad軟體平臺上開發系列工具集，進而在工具集支撐下構建數控導管焊接夾具cad系統; 2 ）應用了數控導管逆向建模技術。
  8. In the mechanics, the class of problems describes the deformations of the elastic beam, of which an end is simply supported and the other is clamped by sliding clamps

    在力學中，這類邊值問題描述了一端簡單支撐，另一端被滑動夾子夾住的彈性梁的形變。
  9. 6 all welding including supports, clips and structural parts shall be completed prior to final heat treatment

    最後熱處理前，應完成所有元件的焊接包括支撐件、夾具和構件。
  10. The bench can hold the heavy and big work piece, the center hole of bench are co - axis with spindle and it can put the clamp convenience

    臺面可支撐重大工件，垂直工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。
分享友人
分享到 Line

分享到臉書