支鉸梁 的英文怎麼說
中文拼音 [zhījiǎoliáng]
支鉸梁
英文
trunnion beam-
The study in the paper starts with beam distortions, and it treats the plastic deformation area as pure bending sect, rest of the beam as rigid bodies. according to different shapes of the external tendons, it divides into three structural forms familiar in projects, that is the beams with no deviator, with a deviator and with two deviators, and studies the relation between the deformation of the external prestressing tendons and that of the beams, and derives the formulas of the ultimate stress increment of external tendons. in the formulas, the ultimate angle corresponding to half of the plastic deformation area is considered as a variable parameter
本文首先從梁極限狀態下的變形入手，將塑性鉸區看作純彎段，將塑性鉸以外的區域看作剛體，按照體外預應力筋的形狀不同，分工程中最常見的三種體外結構形式，即無轉向塊的直線型體外筋混凝土梁、具有一個轉向塊的單折線型梁和具有兩個轉向塊的雙折線型梁，研究體外預應力筋變形和梁體的變形間的關系，推導出以極限狀態下塑性鉸區之半對應的轉角為參數的計算體外預應力混凝土簡支梁以及連續梁的體外筋應力增量計算公式，並進一步求得梁的極限承載力。In tins paper, a new type of standing - wave linear usm with square - ring vibrator was presented, which had two contact surfaces and a support structure with four flexure hinges for the power output
摘要利用有限元分析軟體對方環形直線駐波超聲波電動機的振子進行了動態設計，提出了一種環梁式雙接觸面的振子結構，該振子採用柔性鉸鏈與支撐結構連接，實現力的輸出。Based on the research to the stability variable cross - section beam, the bending defection differential equation of the variable cross - section beam in critical state of bucking is established. according to the edge condition of the structure, the differential equation is solved and bucking equation of variable cross - section beam is created. we can get the algorithm which can be used to calculate the equivalent inertia moment of the variable cross - section lattice structure when it is regarded as constant cross - section of solid web beam
對變截面格構式構件的穩定性計算進行了初步的研究，通過建立變截面構件臨界狀態下彎曲變形的微分方程，根據變形邊界條件，得到了兩端鉸支的變截面梁失穩特徵方程，提出了幾種特殊形式的變截面格構式構件等效為等截面實腹式構件時等效慣性矩的計算方法。After an introduction to the research on the software for the design of the variant steel arched girder construction, the creation of the structural model, the structure of the supporting seat, the design of the variant arched girder, and the measures taken to ensure the stability of the plane surface of the arched girder, the thesis goes to study the methods for the hoisting and the angle setting of the long - span arched girders, as well as the bolting of the axle pin in the hinge support
論文首先對變異鋼拱架結構設計可採用的軟體、結構模型的建立、支座構造形式、變異拱梁的設計，以及保證拱梁平面外穩定所採取的措施等進行了研究，然後研究了大跨度變異鋼拱架弧形梁吊裝、角度的調整、鉸支座穿軸銷等的施工方法，最後對施工完成後的位移進行了實際量測。In this study, sts - - the steel construction design module of pkpm, a software program of china " s institute of the construction science - - is employed to create the construction model in order to study the construction of the supporting seat. a mechanical analysis of the variant arched girders was implemented, with the result that consturction documents meeting mechanical requirements were designed for the hinge support, the roller support and the steel girders
本文採用中國建築科學研究院pkpm軟體的鋼結構設計模塊sts ，從結構建模入手，根據規范要求研究了支座的構造形式，通過對變異拱梁的力學分析，設計出符合力學模型的鉸支座、滑移支座和變異拱處鋼梁的施工圖。Vibrations of an axially transporting beam are investigated
摘要研究帶有扭轉彈簧兩端鉸支軸向運動梁的橫向振動。Vibrations of an axially transporting beam with torsional springs and simply supported
帶有扭轉彈簧兩端鉸支軸向運動梁的橫向振動分析The modified formulae derived from the simplified models, the one of which is the continuous beam on the elastic supports, the other is articulated beam, have been established. being analyzed, the later one is prove more reasonable
文中以彈性支承連續梁和鉸接梁為基礎建立計算模型，並對這兩種方法進行修正，經比較后最終推導出簡化的三跨鉸接梁為計算模型。Based on the conception that the simple beam rotates rigidly around the plastic hinge in the middle when the beam is at the ultimate state of anti - bending capacity, the formula for calculating the stress in the external tendons and the ultimate anti - bending capacity of the beam were developed
摘要在承載能力極限狀態下，可把簡支梁的跨中區段視為1個等曲率塑性鉸（塑性區段） ，其餘梁段可視為直線並處于繞塑性鉸剛性轉動的位置。Structural bearings - part 2 : articulation systems for bridges ; amendment 1
建築業支架.第2部分:橋梁鉸接系統.修改件1分享友人