整件缺失 的英文怎麼說

中文拼音 [zhěngjiànquēshī]
整件缺失 英文
loss of package
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 缺失 : hiatus; deficiency; [遺傳學] deletion
  1. 7. no parts and components or complete power unit warranty will be delivered if gear shaft seize, cylinder scraping or moving friction pad are seriously worn out, resulting in damaging relevant parts or complete power unit, due to lack of oil insufficient engine oil or failure of engine oil or improper use of engine oil following engine instruction

    因缺油機油量不足機油失效或未按發動機使用說明書規定牌號使用機油，導致咬軸抱軸拉缸或各運動摩擦付嚴重磨損，而損壞相關零部件或導致整機毀壞的，相關零部件或整機不給予保修。
  2. The development of society and economy of shanxi province falls behind the advanced regions of china because of the factors of history and natural situation. so the most of the cities of shanxi province are small, and not integrated, and there are few big cities in shanxi province, which makes the medium - sized cities act a very important role in the social economic development of shanxi province

    另一方面，由於受歷史及自然條件的影響，陜西社會經濟發展與東部發達地區相比，仍顯滯后，陜西城市的規模大多較小，城市規模體系不完整，大城市缺失，陜西中等城市在陜西社會經濟發展中的地位益加突出。
  3. The purpose of this paper is to compare the relative efficiency of complete case analysis and the regression calibration method in estimating linear regression parameters when covariates are missing

    摘要本文主要探討在一部份的伴隨變量有缺失下，使用完整資料分析法與回歸校正法估計直線回歸斜率參數時，有效性的比較，並提供回歸校正法比完整資料分析法有效時，斜率參數應滿足的條件。
  4. Theory analysis in this paper pointed out that the flexural - torsional buckling is the usual form of t - section steel. so the slenderness ratio of flexural - torsional buckling should be used when people give out the b / t ratio by the " equal stability " conception. initial stress, defects and tangent modulus are include in the deduce of the paper to get a rational b / t ratio

    通過理論分析指出軸心受力剖分t型鋼整體失穩以彎扭屈曲為主，所以在運用「等穩定」方法確定腹板寬厚比限值時應與桿件的扭轉長細比「掛鉤」 ，並以此為出發點考慮殘余應力、初始缺陷，應用切線模量推導出了較為合理的腹板寬厚比限值公式。
分享友人
分享到 Line

分享到臉書