料位 的英文怎麼說
中文拼音 [liàowèi]
料位
英文
level of material-
Development of intelligent ultrasonic material level meter in monitoring system of material level for coal bunker
煤倉料位監控系統中智能超聲波料位計的研製Verification regulation of gamma ray level meter
射線料位計檢定規程Abstract : in order to mesure the material level under special circumstances, an intelligent weight style material level instrument has been developed
文摘:為了解決特殊環境下的料位測量,研製了一種重錘式智能料位儀。Level meter utilizing ionizing radiation
電離輻射料位計The machine can be used with all kinds of extruders. it can automatically carry plastic powder into the hopper of molding machine by means of a controller of material level, it can save your labor, and realize the safety and reliability
該產品可與各種規格的擠出機配套使用,使塑料粉末粒子從儲料箱自動送入料斗內,並由料位器控制加料循環,實現加料自動化,具有性能穩定,節省人力,安全可靠等特點。Welding consumables - test methods - testing of positional capability of welding consumables in a fillet weld
焊接用料.試驗方法.圓角焊接點的焊接材料位置容量的試驗In order to transmit the data collected to the upper control center, the rs485 network bus technique has been employed in the monitoring system to complete the function of communication between the microcontrollers and upper pc computer. in order to implement the automation of production process, we use fuzzy control algorithm routine in the single chip. lt can adjust the opening angle of electric valves with corresponding voltage according to the real - time material level that measured and so the automation control of material level was implemented
為了實現生產過程的自動化控制,在總結人工手動操作經驗基礎上,單片機控制系統中採用了模糊控制演算法,可以根據實時採集到的高度值輸出相應的電壓控制量來調節輸料管閥門的開度大小,從而實現對料位高度的智能控制。Different bin level indicators ; microcomputer material - blending weighing machine, electronic feed - strip weight ratio equipment
各種料位計,微機配料稱,電子皮帶稱7. in order to meet the requirement of the heat milling system to the height of materials in the preheating jar, the fuzzy - pi control strategy is adopted to design the control system, and both the simulation investigation and the actual application achieve good effect
7 、針對熱磨系統對預熱缸的料位的要求,採用fuzzy - pi控制策略對控制系統進行設計和模擬研究,表明了系統的可行性和有效性,實際應用也取得了良好的效果。Cavity direct cut on a - plate, core direct cut on b - plate
模胚原身出料位This paper introduced a following technicque. the problem of continuously measuring the material level in a wide range using a point radiation source can be solved perfectly with this technique
摘要介紹了一種隨動跟蹤技術,採用該技術的核子料位計較好地解決了利用點輻射源進行大量程連續物位測量的問題。The traditional level measuring methods can n ' t meet our demand because the subjective investigated is in such a poor systemic condition that the temperature is a little high and there ' s so many mill dust and steam there. in this article we perform systemic discuss and research against the dynamic level measuring method under special working condition on the basis of analyzing kinds of level measuring technique in and abroad. first we establish the pressure distribution mathematic model in storage bin and then deduce the mathematic relation between level height and the uniform stress on the bottom of the bin and designed a resistance compressive stress sensor used for the special condition and put forward a resoivement according to its zero excursion existing in practical use
由於本研究系統被測對象環境溫度較高且潮濕,同時料倉中有大量粉塵及蒸汽,因此傳統的料位檢測方法不能滿足本測試要求。本文在分析國內外各種物位檢測技術的基礎上,針對特殊工況下動態物料高度的檢測進行了系統的探討與研究。首先建立了料倉中的壓力分佈數學模型,推導出料位高度與倉底均布壓力間的數學關系式,並據此設計了中溫電阻應變式壓力傳感器,同時對它在實際應用中存在的零點漂移等問題提出了改進措施,提高了傳感器性能,解決了上述特殊工況下動態物料檢測的技術難題。Abstract : the structures and operating principles of several upper bin - level and limit - level monitor - alarm systems were presented in this paper, and their properties and operating effects were compaired
文摘:簡要介紹了幾種料倉高料位和極限高料位檢測報警裝置的結構和工作原理,並就它們的性能特點和使用效果進行了比較。The application of e h ultrasonic material - level meters in the slurry tanks
超聲波料位計在測量料漿槽料位中的應用To comnter the problem of high grinding energy, rapid flow of material, low ratio of material to grinding media, and bad ball coating in common open circuit ferric oxide tube mill, ferric oxide superfine grinding technology markedly increase grinding efficiency and improve grinding status in the tube mill by setting high efficiency sifting equipment, material place regulating technology and subminiature cylpeb
摘要針對普通開流氧化鐵管磨機在氧化鐵生產過程中存在電耗高,流速快,料球比低、嚴重糊磨等問題,通過在磨內設里高效篩分裝蘭,採用料位調節、微型鋼段等技術措施,極大地改善了磨內粉磨工況,提高了粉磨效率。When butyl acetate and isobutyl acetate were selected as entrainer, tower bottom production contained entrainer, with the further decrease of the ratio of water to entrainer
進料處于最佳進料位置時,分離效果最好。隨著進料位置從最佳進料位置上移或下降,分離效果降低。Return pin and cavity interference
回針碰料位Field bus - based material level monitoring system under special operation conditions
特殊工況下基於現場總線的料位監控系統Development and application of an ultrasonic level detector for measurment of cement
一種用於水泥料位測量的超聲波料位儀的研製及應用The improved monitoring system contains three parts : sensors, controllers and executors
傳感器包括水分傳感器、溫度傳感器、流量傳感器、料位傳感器等。分享友人