料筒溫度 的英文怎麼說

中文拼音 [liàotǒngwēndù]
料筒溫度 英文
barrel temperature
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 筒 : 名詞1 （粗大的竹管） a section of thick bamboo 2 （粗管狀物） thick tube shaped things 3 （衣服等...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 溫度 : [物理學] temperature
  1. When demanded temperature is achieved, the roller will rollback, the materials will be discharged under function of guiding board

    達到工藝溫度后，滾筒反轉，物料在導斜板的作用下迅速卸出。
  2. After reaching demanded temperature, the roller will rotate reversely, and the materials will be fast discharged under function of guiding board

    達到工藝溫度后，滾筒反轉，物料在導斜板的作用下迅速卸出。
  3. Abstract : this paper studies the structure, function and realization of ceramic / metal gradient thermal barrier coatings dynamic design software by combining the conceptions of thermal barrier coatings ( tbcs ) and functional gradient materials ( fgms ). through a typical example, it compares and analyses the simulation results of temperature field in the multiplayer gradient cylinder model calculated by analytical method, finite difference method and finite element method

    文摘:結合熱障塗層和功能梯度材料的概念，研究陶瓷/金屬梯度熱障塗層動態設計軟體的結構與功能及其實現過程.通過具體的例子，對多層圓筒模型的溫度場的解析解、差分解及有限元解的模擬結果進行了比較及分析
  4. Abstract : in the thesis, the effect factors of the extrudate temperature have been researc hed during the processing of twin - screw extruder

    文摘:研究了在雙螺桿擠出過程中，影響藥料溫度變化的有關因素，認為第一段機筒溫度是影響藥溫的顯著因子。
  5. Sbs use the cylinder temperatures of 140 - 180c and can increase by 20 - 30c from the feed zone to injection zone

    Sbs用140 - 180c炮筒溫度，可以20 - 30c分段由進料區逐漸提升到射嘴區
  6. Flame tube in aircraft engine undergoes high temperature and high speed airflow washing. a hypothesis was suggested, which takes the transient heat transferring as the main reason to the cracking and damage on flame tube. finite element method was adopted to simulate the thermal fatigue and the hypothesis was reproduced

    發動機火焰筒的熱疲勞損傷是導致火焰筒失效的主要原因，本文提出了一種火焰筒熱疲勞損傷假設，認為火焰筒熱疲勞損傷不是由於發動機的運行和停車時冷熱溫度循環造成的，而是發動機啟動時瞬態溫度傳導過程中材料循環塑性變形的結果，利用該假設結合有限元計算模擬了火焰筒產生疲勞損傷的原因。
  7. In the forth section, the dynamic matrix control strategy is discussed

    第四章：注塑機料筒溫度的動態矩陣控制。
  8. 3 stages of temperature control, 2 levels of injection pressure, non - stage abjustment injection speed and back pressure, be suitted in precise shaping of engineering plastic

    料筒油溫控制，兩極注塑壓力，射速、背壓無段調整，上、下模具溫度獨立控制。
  9. Temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared

    對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。
  10. Abstract : temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared

    文摘:對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。
  11. To explore why the ratio of collectable wort extract is higher than that of non - extruded, the influences of all parameters of rice extrusion system ( barrel temperature, material moisture, screw speed ) on resistant starch content of extuded rice were studied by using second - order quadratic orthogonal rotating combination design method

    摘要為探索擠壓蒸煮大米啤酒輔料麥汁浸出物收得率高於傳統不擠壓蒸煮啤酒輔料收得率的原因，用二次正交旋轉組合試驗法設計安排試驗，研究了大米擠壓蒸煮系統諸參數（套筒溫度、物料含水量、螺桿轉速）對大米抗性澱粉含量的影響規律。
  12. The closed - loop control of barrel temperature of precision injection molding machine

    精密注塑機料筒溫度的閉環控制
  13. In the third section, the pid and fuzzy control method are discussed

    第三章：注塑機料筒溫度的pid控制及模糊控制。
  14. In the end, considering that the barrel is coupling, a decoupling control and thereafter fuzzy control method are discussed

    最後根據注塑機料筒溫度對象是強耦合的特點，研究了其解耦和模糊控制方法。
  15. Firstly the principles of predictive control are introduced. later, multi - variable dynamic matrix control algorithm is put in practice on the decoupling control of extruder barrel

    首先介紹了預測控制的發展及現狀，接著討論了動態矩陣控制的原理，最後應用多變量動態矩陣控制策略實現了對料筒溫度的解耦控制。
  16. The results showed that the color difference was decreased, at the same time, the loss of the soluble protein and amino acid contents were decreased with increase of sample moisture and decrease of barrel temperature ; when increased the revolving speed, the color difference was decreased as a whole meanwhile the contents of soluble protein and amino acid were increased at the beginning and decreased in the end

    結果顯示，提高進料水分，降低機筒溫度，有利於降低擠壓蛋黃粉的色差值，並能減少可溶性蛋白質和氨基酸的損失；螺桿轉速提高，擠壓蛋黃粉的色差值呈總體降低趨勢，而可溶性蛋白和氨基酸的含量呈先提高后降低的趨勢。
  17. The paper puts forward an idea of designing for stove temperature of injection machine control system by designing the fuzzy set theory, and introduces the structure of the fuzzy controller, the design procedures of the fuzzy control regulations and realization method

    摘要根據注塑機料筒溫度的自動控制問題，提出了採用模糊控制理論來設計溫度控制系統的思路，並介紹了模糊控制器的結構、模糊控制規則的設計及實現方法。
  18. In the fifth section, the generalized predictive control strategy is discussed at first. after that, the author applies the generalized predictive control algorithm to the real - time control of extruder barrel. the last section is a summary of the whole research work

    首先簡要介紹了廣義預測控制的原理，然後對其在注塑機料筒溫度控制上的應用進行了初步研究，採用單變量廣義預測控制方法對單段料筒溫度進行了有效的控制。
  19. Firstly demands of hardware and software designs of injection molding machine and realization are described. secondly software design of injection molding machine is discussed, and then frequency - converting control temperature control of injection molding machine are expatiated. finally hardware and software designs of manipulator specially used in injection molding machine are detailedly explained

    首先介紹了注塑機控制器硬體設計的需求和設計實現，然後分析了注塑機控制器的軟體設計，並對注塑機控制器中流量的變頻控制和料筒溫度控制進行了詳細的闡述，最後對注塑機專用機械手控制器的軟硬體設計進行了詳細的介紹。
  20. Through orthogonal experiment design, the preparation technology of reactive extrusion dynamic vulcanization for low hardness epdm / pp blend thermoplastic dynamic vulcanizates was studied, and the effects on micromorphology of extruded vulcanizates of such main technological factors as barrel temperature, feed screw driven voltage and host machine screw rotation rate were discussed

    摘要通過正交試驗設計，研究了低硬度epdm / pp共混型熱塑性動態硫化膠的反應擠出動態硫化制備工藝，初步探討了機筒溫度、喂料螺桿驅動電壓及主機螺桿轉速等主要工藝因素對擠出物微觀相態結構的影響。
分享友人
分享到 Line

分享到臉書