斜航地 的英文怎麼說
中文拼音 [xiéhángde]
斜航地
英文
loxodromically-
The directrixes of the in former two transmissions are the loxodrome and the geodesic on the pitch cones, that of the latter is an equal - pitch line along the direction of straight generatrixes in the hyperboloid surface, also is the vertical trajectory of the straight generatrixes
前兩種傳動形式的準線分別為節錐面上的斜航線與測地線，後者的準線為單葉雙曲面上沿直母線方向的等螺距曲線，且為直母線族的正交軌線。Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece
將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義Basing on the premise that the capability of the transmission and the technique are synthetically considered, three new kinds of gear pairs is given, that is, loxodromic normal circular - arc spiral bevel gears, geodetic normal circular - arc spiral bevel gear, and hyperbolic normal circular - arc gear
在綜合考慮傳動性與工藝性等要求的前提下，提出斜航式與測地式法向圓弧螺旋錐齒輪傳動、雙曲型法向圓弧齒輪傳動等兩類三種齒輪副的構思。Based on studying a long focus oblique real - time aerial camera, this paper studys the reason of being out of focus systematically, and points that the primary reason of being out of focus is due to the change of environment ( temperature > atmospheric pressure ) and oblique photographic distance, and according to the three factors, talk about the effect on being out of focus of camera, the simple maths equation is presented in order to calculate out of focus
基於一種長焦距斜視實時航空相機的研製，深入地探討了導致相機離焦的原因，指出環境（溫度、大氣壓力）變化和照相距離的變化是導致相機離焦的主要原因，分別從溫度、大氣壓力、照相距離這三個方面的變化對相機離焦的影響進行研究，給出了計算相機離焦量的簡化數學模型。The computations are shown to agree well with available experimental and numerical data and the physics of 3d large - scale flow separations and vortex shedding are confirmed. the simulation of the flow around a maneuvering wigley hull is a demonstration of capability for calculations of sway forces and yaw moments acting on a hull moving obliquely at a large range of yaw angles. the focus of study is large - scale cross - section separation flows, bilge - vortex development along the hull in the longitudinal direction and their effects on hydrodynamic forces
應用所開發的求解器，以wigley船型為算例計算了大角度斜航船體粘性流場和水動力，分析了漂角的變化對船體所受到的粘性水動力的影響，相當精確地預報了以橫流分離和般渦生成與泄出為特徵的操縱運動船體特有流動形態及橫向水動力和轉脂力矩，經與現有試驗和計算數據比較，檢驗和驗證了該求解器精確模擬繞斜航運動船體的大尺度分離流動和計算非線性水動力的能力。Oblique views of some areas are also available. enlargement of an aerial photograph can be made to the maximum of 5x for colour photograph and 8x for black and white photograph
此外，測繪處亦備有本港部分地區斜角航空照片。彩色航空照片可放大至5x大小，黑白的則可放大至8x大小。分享友人