斜角接觸 的英文怎麼說

中文拼音 [xiéjiǎojiēchù]
斜角接觸 英文
angular contact
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 斜角 : [數學] [物理學] oblique angle; [機械工程] bevel angle斜角規 miter square; bevel; bevel square; sa...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. This then allows the lower plate lug to make contact of its two corners with the slanting walls of "v" groove.

    這便於下面的極板年的兩角與「V」字形溝槽的兩個傾斜的壁相接觸。
  2. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  3. Hold the test specimen by the edges at an angle above the pre - cleaned microscope slide. the specimens should not touch the slide

    手持測試樣本的邊端以一定的角度傾斜在光片的上方。樣本不應接觸光片。
  4. The influence of the slant on maximum stress in contact area is studied and the axial movement formula is modified. the idea of contact angle is presented to study the direct influence on the axial movement. 2

    研究了這種傾斜對接觸區最大壓應力的影響，對回轉窯軸向下滑計算公式進行了修正；提出了接觸角的概念，分析了這種傾斜對窯體軸向運動速度的直接影響。
  5. This then allows the lower plate lug to make contact of its two corners with the slanting walls of " v " groove

    這便於下面的極板年的兩角與「 v 」字形溝槽的兩個傾斜的壁相接觸。
分享友人
分享到 Line

分享到臉書