方向螺絲 的英文怎麼說
中文拼音 [fāngxiàngluósī]
方向螺絲
英文
traversing screw-
3 please screw down safety screw before installation, and screw down the component of pawl and rolling wheel anticlockwise according to opening direction of fingernail axis
3安裝前請退出保險螺絲,按爪軸的開口方向將棘爪與滾輪組合件按反時針方向退出。Once correct flow rate setting has been established, slide memory screw counter - clockwise towards closed side of indicator plate until memory stop ring hits indicator plate
一旦確定正確的流量設置,則將記憶螺絲朝著指示器板的關閉位置逆時針方向旋轉,直到記憶止動環觸到指示器板為止。To make the tilt front - up, loosen the set screw, insert a screwdriver into the feed bar shaft, and turn it by 90 in the direction of arrow mark
想要向前上方傾斜時,請擰松固定螺絲,把螺絲刀插進送布臺軸,朝箭頭方向轉動90 。Knuckle arm fixing bolt replacement
更換方向臂緊固螺絲修正運動Unscrew # 2 check ( turncounter - clockwise ) by placing along screwdriver across lugs and applying pressure to loosen # 2 check
將螺絲起子向前插入穿過凸耳桉逆時針方向旋轉2號止回閥的螺紋,並施加壓力松開2號止回閥。Open the small door to the lower and rear part of the machine, you can see the general switch of the machine, audio switch, optical drive, floppy disk drive. you can do simple operation over the computer. unlock the special lock, the whole lower part of the cabinet can slide backward, and then the industrial control chassis as well as the mainboard, cpu and hard disk can be seen
在一體機的下部只要打開後方的單獨小門,就可以露出一體機總開關,音響調節及主機光驅軟驅,對主機進行簡單的操作另外打開專用鎖后可使整個下部箱體沿軌道向後出,露出工控機箱和裝在其中的主板cpu硬盤,以便進一步進行維修升級操作,松開四個緊固螺絲即可方便的取出工控主機箱。If adjustment is required, turn adjustment control with screwdriver in either direction slowly until vibration or hum stops
如果需要調節,則用螺絲刀從兩個方向慢慢旋轉調節控制,直到振動或蜂鳴聲停止。Remove compression from spring by turning adjusting screw ( 1 ) counterclockwise
通過反時針方向旋轉調節螺絲( 1 )從彈簧上拆卸壓縮件。To increase the reduced pressure, turn the adjusting screw clockwise - opposite to decrease the reduced pressure
增加減少的壓力,順時針方向旋轉調節螺絲;相反則是減少減少的壓力。Members after sailing should return the key lock and fin to the ao and sign off on the register
會員應向行政辦處事處登記退還短板手續,並確保所有短板尾鰭及尾鰭螺絲均已交還方可離開。Turn thread tension screw 2 toward a to increase the bobbin thread tension, or toward b to decrease it
向a的方向轉動線張力螺絲2之後,底線張力變強,向b的方向轉動之後,底線張力則變弱。Turning the oil amount adjustment screw attached on the hook driving shaft front bushing in the “ + ” direction ( in direction a ) will increase the amount of oil ( oil spots ) in the hook, or in the “ ? ” direction ( in direction b ) will decrease it
把下軸前端金屬部件上的油量調詳螺絲向的方向( a方向)轉動,油量變多,向的方向( b方向)轉動,油量變少。Hence, we have no plans to require the wheels of imported vehicles to be tightened by wheel nuts threaded in opposite directions
因此,我們沒有計劃?制要求入口車輛的車輪採用相反扭緊方向的螺絲。It has been reported that some academics suspect that one of the possible causes of the recent accidents involving wheels coming off vehicles in motion might have been the direction in which the screws of the wheels were tightened
問題:據報,有學者估計近期多宗行駛中車輛車輪松脫意外的成因之一,可能與車輪的螺絲扭緊方向有關。Whether it will consider making it a mandatory requirement that the screws of the wheels on the left and right sides of imported vehicles must be tightened in the opposite directions ; if so, of the details ; if not, the reasons for that
會否考慮強制要求入口車輛的左右方車輪的螺絲扭緊方向必須相反;若會,詳情為何;若否,原因為何?分享友人