方程換算 的英文怎麼說

中文拼音 [fāngchénghuànsuàn]
方程換算 英文
scaling of equations
  • 方 : Ⅰ名詞1 （方形; 方體） square 2 [數學] （乘方） involution; power 3 （方向） direction 4 （方面） ...
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 換 : 動詞1. （給人東西同時從他那裡取得別的東西） exchange; barter; trade 2. （變換; 更換） change 3. （兌換） exchange; cash
  • 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
  • 換算 : [數學] matrixing; scaler; conversion; convert; translation換算表 conversion table; equivalent tab...
  1. The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established

    論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。
  2. In recent years, plentiful and substantial fruits achieved by the lb method in simulations of hydraulics, multiphase flows, flows in porous media and heat transfer as well as magnetohydrodynamics, have revealed a broad perspective of application of this method, it will become a powerful competitor to the conventional approaches. in order to absorb the recent achievement in theory and application of the lb method, explore new ways in hydraulic computation to promote the development of practice, some work is car ried out in this thesis, as following : advances in the theory research and application, deductive process of the d2q9 model and some other commonly used models of the lb method are summarized. based on the hydrodynamic and general boundary conditions, a new joint boundary condition is presented, it integrates advantage of the two conditions above and obtains very good results in dealing with all kinds of boundaries of flow fields

    為了消化和吸收近年來lb方法在理論和應用方面的新成果，探索在水力計算方面的新途徑以促進lb方法實用化的發展，本文進行了下列研究工作：綜述了lb方法在理論研究和實際應用方面的新進展，以及d2q9模型的推導過程和其他一些常用的模型；在水動力邊界條件和通用邊界條件的基礎上提出了一種新的聯合邊界條件方法，它綜合了上述兩種邊界條件的優點，在流場的各種邊界處理中取得了非常好的效果，經過模塊化的處理以後這種邊界條件具有更好的實用性；針對均勻網格的lb方法計算效率較低的不足，提出了雙重網格的latticeboltzmann方法，通過二維poiseulle流動、后臺階流動和渠道方槽流動三個算例的模擬，證明這種方法能夠明顯地提高流場模擬的計算效率；此外，根據復雜區域流場的特徵提出了latticeboltzmann方法的分塊-耦合演算法，利用lb方法的計算特性實現塊與塊之間的數據交換，充分利用計算資源提高計算效率，通過對「 t 」型、 「十」型和「 x 」型分岔管道流場的模擬，展示了這種演算法的特徵和優點，以及它所具有的應用前景。
  3. The best scheme was chosen after analysis and comparing and the structure was designed. at same time, the kinematics analysis was conducted, coordinate transformation matrix using d - h method was set up, and the kinematics equation direct solution and inverse solution was deduced, the velocity jacobian matrix was constructed using vector product method, and the values of displacement and velocity of some special point including the wrist point were calculated. secondly, the working space of the robot was analyzed and the axes section of practical working space was drawn

    首先，作者針對機器人的設計要求提出了多個方案，對其進行分析比較，選擇其中最優的方案進行了結構設計；同時進行了運動學分析，用d - h方法建立了坐標變換矩陣，推算了運動方程的正、逆解；用矢量積法推導了速度雅可比矩陣，並計算了包括腕點在內的一些點的位移和速度；然後藉助坐標變換矩陣進行工作空間分析，作出了實際工作空間的軸剖面。
  4. So the model is more integral and accurate in describing the performance of heat and mass transfer in the adsorbent bed than the traditional mathematical model. 4. pens ( perturbational exponential numerical scheme ) is adopted to ensure the successful solving of the mathematical model and the reliability of results

    採用攝動精確數值解格式（ pens ）來求解數學模型中的主要控制方程，並且考慮到控制方程的非定常性，對原pens格式進行了非定常變換，保證了數學模型計算的成功和結果的可靠性。
  5. Least squares solution of equation is used to calculate and adjustment transformation matrix at same time, transformation matrix is used to calculate the 3 - axis angle of star sensor. so is very fast and precise

    利用方程組的最小二乘解求取轉換矩陣，通過轉換矩陣計算星敏感器的三軸姿態角，使姿態計算和平差同時進行，具有較高的姿態計算精度和計算速度。
  6. This thesis was divided into eight chapters, and the main results and innovations obtained here can be summarized as follows : ( 1 ) the physics model of tsrs in frequency conversion crystals has been built up firstly. based on quantum - mechanical viewpoints and the following physical processes and parameters : the two - photo interaction of light with matter, paraxial diffraction of stokes, langevin noise sources, reflection at the faces and the edges of crystals, gain coefficient, beam aperture, pulse width and fluence of 3, the physics model of tsrs in kdp and kdp crystals acting as high - fluence frequency convector and the paraxial operator maxwell - bloch - langevin equations have been built up

    全文共分八章，取得的主要成果及創新點如下： （ 1 ）首次建立了諧波轉換晶體的tsrs物理模型本文根據量子力學原理，在考慮如下物理過程和參量的基礎上：光與物質的雙光子相互作用； stokes光的傍軸衍射； langevin （郎茲萬）噪聲源；晶體表面反射和端面反射；增益系數、光束口徑、脈寬和三倍頻光能量密度，推導出高通量激光在kdp和kd ~ * p諧波轉換晶體中的tsrs物理模型和空間上的近軸算符maxwell - bloch - langevin方程組。
  7. In this paper, i consider the traveling wave solutions and peakons of the generalized camassa - holm ( gch ) equation and give the express of the solitons of this equation. the peakons and their figures of the gch equation are given with the mathematic software for m - 1, m = 2 and m = 3 in particular ; for m = 3, i get the generalized dissipative camassa - holm equations by adding a dissipative term and find two types exact traveling wave solutions of this equations. i also apply the homogeneous balance method into the gch equation so that i get a group of smooth solutions for m = 2 and m = 3 and the backlund transformation for m - 3 of the gch equation

    本文研究廣義camassa - holm （ gch ）方程的行波孤立子解及尖峰孤立子解，給出gch方程的行波孤立子解的表達式，特別的，對m = 1 、 m = 2 、 m = 3時利用mathematica數學軟體進行計算，解出了gch方程的尖峰孤立子解，並給出了此時gch方程的尖峰孤立子解的圖形，使數值分析和理論相結合；對m = 3時的gch方程增加一耗散項u _ （ xx ）后得到廣義耗散camassa - holm方程，並解出此方程的兩類精確行波解；本文將齊次平衡法應用到gch方程中，解出m = 2 、 m = 3時的gch方程的一組光滑解，同時應用此方法得到了m = 3時的gch方程的backlund變換。
  8. Because geometry of formation of two satellites is very weak, the solution covariance is very big and unstable in order to resolve this problem, the measurement model was transformed from cartesian coordinate system to sphere coordinate system

    由於雙星編隊星座觀測的幾何結構弱，所以解算參數的協方差不穩定。為了解決這一問題，對測量方程進行球坐標變換。
  9. Based on the correct evaluation of the means and covariance of the measurement error in cartesian coordinate system, the algorithm processes the radar measurements sequentially, and the linearization of measurement equation is no longer neccessary

    作者推導了有測速數據時的去偏轉換卡爾曼濾波演算法。此演算法估計精度和計算效率比以前的方法有較大改善，對測量方程不做近似處理。
  10. In the paper, with system energy balance method and heat conductive equations ， on tne basis of short time heat transfer modeling established the long time modeling, considering heat interference in thermal well group. this paper used the finit element method for element division and computer analysis, and provided the operation temperature figure. acquired computation values agreed well with experimental results, the most difference between them was 5. 13 %

    本文採用系統能量平衡結合熱傳導方程，在淺埋套管式換熱器短期傳熱模型基礎上建立了長期傳熱模型，並考慮了管群熱干擾對模型的影響。並運用有限單元法軟體編程進行離散和計算機分析，得出模擬溫度場，其模擬值與實測的均值基本相符，兩者最大誤差小於5 . 13 % ，表明該模型具有一定的合理性和實用意義。
  11. Finally, the fatigue equation and axle load conversion are applied to forecast the steel bridge deck pavement ' s service life of nanjing second yangtze river bridge

    結合南京長江第二大橋鋼橋面鋪裝工程，應用所建立的疲勞性能方程以及軸載換算公式對鋼橋面鋪裝層使用壽命進行預測。
  12. Based on the fem program on fracture of plane structure developed by professor fu xiaoling of ho hai university, a two demension damage and fracture finite program package which is programed in fortran 90 language is developed. the paper adopts the plane - eight - nodes isoparameters element and compute the developing law of the damage and macro - damage of plane structure under load. considering the original damage and tension and compression damage at the same time, the paper adopts the more reasonable concrete constitute relation of two demension and exponent function model

    在河海大學符曉陵副教授所編制的平面結構斷裂有限元程序（ dl08p4 ）基礎之上，本文用fortran90語言編制的二維損傷-斷裂有限元程序包，程序採用平面八結點等參數單元分析計算平面結構在外荷載作用下損傷及宏觀裂縫的發展規律，考慮了混凝土結構體內存在著初始損傷和同時存在的拉、壓損傷，並且採用更為合理的具有損傷含義的混凝土二維本構關系（即正交異性損傷模型中的本構方程）和指數函數模型建立的並可進行拉、壓損傷可比性換算的損傷演變方程，較為真實地反映了實際情況。
  13. For the mesoscopic metal ring system in external magnetic field, supposing the system has a symmetry under translation in charge space, the quantum current and the quantum energy spectrum in mesoscopic metal ring are given by solving thire eigenvalue equations ; and the quantum fluctuations of the current and the energy have been calculated by the character of the minimum shift operator

    摘要針對處于外磁場中的介觀金屬環系統，假設在電荷空間中具有變換的對稱性，通過求解本徵值方程給出系統的量子電流、能譜關系；利用最小平移算符的性質等，計算介觀金屬環中電流和能量的量子漲落。
  14. For one - dimensional mesoscopic metal rings system in external magnetic field, supposing the system has a symmetry under translation in charge space, the quantum current relation in mesoscopic metal rings is given by solving the eigenvalue equation of the current, the property of quantum current have been investigated and analysed

    摘要針對處于外磁場中的一維介觀環系統，假設在電荷空間中具有變換的對稱性，通過求解電流算符的本徵值方程，給出系統中的量子電流關系，分析和研究一維介觀金屬環中量子電流的性質。
  15. As to the simulation, three - dimensional n - s equations and two - phase flow model, in which the liquid toluene spray as discrete particles was considered, were employed to describe the turbulent combustion processes in the combustion chamber. the mass and energy transfer between the two phases were calculated by the droplet evaporation model, and the arrehnius model was used to obtain the gas chemical reaction rate. the details of 3d flow field, the distributions of temperature and compounds were obtained by solving the equations

    數值模擬方面，應用三維湍流n - s方程以及顆粒軌道模型描述了激光器燃燒室內部的噴霧兩相燃燒流動過程，兩相之間的質量、能量交換由液滴蒸發模型計算，氣相化學反應速率由arrhnius公式計算，通過耦合求解氣液兩相模型方程，模擬了燃燒室三維流場，得到了燃燒室內的溫度和組分濃度分佈。
  16. Different equations to corresponding components are presented by analysing and transformating the general equations of fluid routes, then static characteristics mathematical model of liquid propellant space propulsion system is presented. based on the data of static characteristics calculation, mass model of thruster, propellant, propellant tank, gas, gas bottle, pipe and valve is presented using both the method of statistical regression and the method of stress analysis, then corresponding mass model is presented. based on the characteristics of liquid propellant space propulsion systems, analyse the five phases ( concept and definition, design and improvement, manufactureing and arrangement, operation and ma intenance, disposal ) in which life cycle cost of liquid propellant space propulsion systems is cost separately, then discompsed structure of life cycle cost and model of life cycle cost are presented

    將組件分成氣路組件和液路組件，再對氣路組件和液路組件進行相應的分類，然後通過對通用流路方程進行分析和變換對不同類型的組件分別建立不同的方程，從而建立了一個適用於液體推進劑空間推進系統的靜態數學模型；根據靜態計算所得到的數據，應用統計回歸法和應力分析法分別建立推力室、推進劑、推進劑貯箱、氣體、氣瓶以及導管和活門等的質量模型，從而建立相應的質量模型；結合液體推進劑空間推進系統特點，對液體推進劑空間推進系統全壽命周期費用發生的五個階段（概念和定義、設計和改進、製造和安裝、運行和維修、處理）分別進行分析，建立了液體推進劑空間推進系統全壽命周期費用分解結構和全壽命周期費用模型。
  17. Velocity variation is positively correlated with crust thickness and negatively correlated with earth ' s heatflow. the linear regression equation of velocity, crust thichness and heatflow is obtained. the regression coefficient dv / dp convert

    同時地震波速廠與地殼厚度h呈明顯的線性正相關關系，與大地熱流呈負相關關系，並得到三者的線性回歸方程，回歸系數dv dh換算成bv op ？
  18. Abstract : based or the basic operating condition of road stimulation, this paper discusses the intensifying test technology and brings up the basic method and principle of intensifying test, it also gives the busic translating function of equiualent mileage and the primary design of intensifying test

    文摘:該文從路面對車輛激勵的最基本工況研究出發，對強化試驗技術進行較深入的探討，提出了強化試驗的基本方法和思路及當量里程換算的基本公式，最後提出了開展車輛強化試驗研究的一些初步設想。
  19. In this dissertation, the numerical computation for the acoustic radiation problem ( arp ) is studied deeply and systematically in the theory, method and the application technique, based on analyzing the situation of the home and abroad on the numerical computation for the acoustic radiation problem. the calculation formulas of the boundary element method ( bem ) for the exterior acoustic radiation problem in the full - space and half - space are deduced, based on the wave propagation theorem ; the arising of the non - unique solutions, which is associated with the application of the boundary integral equation ( bie ) in acoustic radiation problem, is analyzed and proofed ; the improved combined helmholtz integral equation formulation ( ichief ) is presented to overcome the non - uniqueness problem more effectively and reliably ; the determination of the singular integral coefficients on various occasions is analyzed ; the properties and treatments of the singular integrals with different orders axe studied ; the computation program of the cubic spline ichief is developed and its ability to overcome the non - uniqueness problem and feasibility to discrete the surface coarsely with the sufficient calculation precision are examined through examples

    第二章在聲波動理論基礎上，詳細地推導出對應于無限域和半無限域的外部振動聲輻射問題的邊界積分方程計算公式；根據fredholm積分理論，對利用邊界積分方程計算振動聲輻射問題過程中解的非唯一性的產生進行了分析和證明；改進了chief法以提高其克服解的非唯一性的有效性和可靠性；對不同條件下奇性系數的計算、強奇性積分的收斂性及其在變量替換時與普通積分的差異性、不同階奇性積分的計算、數值求積分等進行了研究；開發了三次樣條改進chief法計算軟體，並通過算例考核了該方法在特徵波數處克服解的非唯一性的有效性和在保證計算精度的前提下實現剖分粗化以提高計算效率的可行性。
  20. This paper suggests that the integral of the state equation is evaluated directly through the exponential matrix based on the pim, thus several series solutions are obtained. utilizing the symmetry of matrices and the idea of substructure, the computational precision and efficiency of the pim are improved

    本文深入研究精細積分及動力方程演算法，基於指數矩陣計算、 pade逼近理論，在時域上對非線性動力狀態方程直接積分求解，構建若干系統響應求解格式，並分析了演算法精度、效率；通過矩陣變換，利用矩陣對稱性、子結構等方法改進精細積分計算效率。
分享友人
分享到 Line

分享到臉書