施焊部分 的英文怎麼說

中文拼音 [shīhànbùfēn]
施焊部分 英文
welding portion
  • 施 : Ⅰ動詞1 （實行; 施展） execute; carry out 2 （給予） exert; impose 3 （施捨） give; hand out; best...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 部分 : （整體中的局部或個體） part; section; portion
  1. Welding of reinforcing steel - part 1 : execution

    鋼筋焊接.第1部分:施工作業
  2. It consists of two part, the one is hardware : integrating the system of the arc welding robot ' s hardwares and its working principles, separating and extracting the original system ' s control signals, designing the control system openly and its working principles, constructing the structure and principle of the motion card based on dsp, designing the telecontroling teaching box or control panel of touching screen based on usb interface, applying for some software and hardware measures on control system ' s anti - jamming ; the other is software : putting forward the three levels opening software structure model of arc welding, comparing the opening of software structure model between osaca and ours, putting forward the solutions of the pri and communication among the threads of software system ' s modules, using the dll ' s techniques to solve software ' s module design and putting forward the frame codes, bringing forward the path planning software ' s realization by cp + ptp mode, discussing the real time of windows2000 operating system and advancing its solution

    具體包括，硬體部分：弧焊機器人硬體整體系統集成及其工作原理，原系統控制信號的分離和提取，控制系統的開放式設計及組成原理，基於dsp的運動控制卡結構和原理，基於usb介面的觸摸屏式遙控示教盒控制面板的設計，系統抗干擾的軟、硬體措施；軟體部分：提出了弧焊機器人的三層開放式軟體結構模型，軟體結構模型與osaca的模型進行開放性比較，給出軟體系統各模塊線程間優先級和通訊的解決方案，使用動態鏈接庫技術實現軟體模塊化設計並給出了框架代碼，給出了cp + ptp方式的軌跡規劃軟體實現過程， windows2000操作系統實時性問題的討論及解決方案。
  3. Solderless connections. part 1 : wrapped connections. general requirements, test methods and practical guidance

    無焊連接件.第1部分:纏繞連接件.一般要求試驗方法和實施規范
  4. Solderless connections - part 7 : spring clamp connections ; general requirements, test methods and practical guidance

    無焊連接.第7部分:彈簧夾件連接.一般要求試驗方法和實施指南
  5. Firstly, the analyses on the dynamical response of the tsing ma bridge ( tmb ) under traffic loading are performed on the basis of the three dimensional finite element model of the full - scale structure of the bridge, and some regions critical to fatigue damage are determined from the result of the dynamical response. the hot spot stress approach is usually adopted in the fatigue design and analysis of tubular welded joints. to apply the hot spot stress approach for the fatigue evaluation of long - span suspension bridges, the fem is further used to determine the hot spot stress of the critical fatigue locations

    首先，在青馬大橋三維有限元模型和整體動力響應分析計算的基礎上進一步進行關鍵疲勞構件的局部熱點應力分析，對疲勞危險部位處的焊接構件建立三維有限元模型，施加符合橋梁實際工況的載荷與位移邊界條件，進行局部熱點應力分析，確定這些焊接構件內的名義應力和相鄰焊接區域內熱點應力之間的關系，得到相應的應力集中系數。
  6. This page describes the initial surface treatment for steel plates, secondary surface treatment for welded steel and the application of repair paint

    這一部分講述了對鋼板的表面預處理，對焊接后鋼材的二次表面處理以及修補用漆的施工。
分享友人
分享到 Line

分享到臉書