旋扭法 的英文怎麼說
中文拼音 [xuánniǔfǎ]
旋扭法
英文
twisting-
Crenshaw deciphered the algorithm of the twisting motion, known as helical klinotaxis, and assisted nekton ' s team in applying it to the robots, in essence crafting a new guidance technology
克倫肖解算出螺旋狀調轉趨性這種扭擺運動的運作法則,並協助耐頓研究所的團隊設計機器人,基本上是要發展出一種全新的導向技術。In this paper, the rotating machinery at high speed is studied. there are discussed about numerical calculating methods for non - linear dynamical system, the rotor system radial impact and rubbing dynamics behavior analysis having the nonlinear rigidity on the unsteady and non - linear oil film, the rotor system dynamics behavior analysis with bending - torsional - pendular coupling vibrations, application of wavelet, fractal and network in fault diagnosis. the main works in this paper are as follows : ( 1 )
本文以高速旋轉機械為主要研究對象,系統、深入地研究了非線性動力學系統的數值計算方法、具有非線性剛度的轉子系統在非穩態非線性油膜力作用下的徑向碰摩動力學行為、轉子彎扭擺耦合振動的動力學分析、小波和分形理論及人工神經網路在故障診斷中的應用問題。The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed
研究表明,採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料,軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數;試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著;超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比,斷裂強度和延伸率均有一定程度的增強;超細晶ly12的熱膨脹系數在550左右發生明顯的變化。In newtonian mechanics, we say the moon is attracted by the earth, so it orbits around the earth. in the theory of general relativity, we will say the earth affects the spacetime around it, thus the moon is no longer moving in a straight line, instead it goes around the earth. just like a marble will not move in a straight line on an uneven table
牛頓力學認為月球繞地球旋轉,是因為月球受到地球引力的吸引但廣義相對論的說法則是地球的質量扭曲了附近的時空,月球在不平坦的時空以最自然的方式運行,結果走出了一條繞著地球轉的曲線,情況就如彈珠在不平坦的地面走,會左搖右擺一樣。Adopting the method that the theory combines with experiment, solve the problem of rotate, seal, speed of assigning limit of the torsion, nozzle initially sequentially, nozzle assign and limit speed problem
採用理論與實驗相結合的方法,依次解決旋轉密封、起始旋轉扭矩、噴嘴布置和限速問題,設計了自旋轉噴頭。The running condition would be deteriorated and at last the parts of the engine would be damaged if the revolution were reduced too low. the propeller must be redesigned or be modified in this situation. people usually modify the propeller rather than change the propeller because it will be more easily and economical
此時若要更換新的螺旋槳必然造成經濟上過重的負擔,較方便可行的方法是對原來的螺旋槳採取切邊修改的方法,減少螺旋槳的直徑、盤面積或螺距,使螺旋槳的扭矩減小,螺槳變「輕」 。Test method for mechanical torque rate of spiral coils of thermostat metal
恆溫雙金屬制螺旋線圈的機械扭轉率的試驗方法The surface panel method has been applied to predict the hydrodynamic performance of highly skewed propeller. the surface of propeller and its trailing vortex are discreted by a number of small hyperboloidal quadrilateral panels with constant source and doublet distribution. for highly skewed propeller, the conventional method generating grid oriented along constant radii will result in a high aspect ratio and a high skewness and a twist panel near the propeller tip on blade surface, which result easily in incorrect calculation results of velovity on blade surface, even in iteration divergence and calculation failure. a “ non - conventional grid ” is developed to acoid these problems. this grid can effectively solve the problem of the calculation and convergence for highly skewed propeller. the non - linear kutta condition of equal pressure on upper and lower at the trailing edge is executed by the iterative procedure. by sample calculating, the obtained results are satisfied the experimental data
採用面元法預報大側斜螺旋槳水動力性能,螺旋槳表面及尾渦面離散為四邊形雙曲面元,每個面元上布置等強度源匯和偶極子分佈.對于大側斜螺旋槳而言,槳葉表面採用常規的等半徑網格劃分方法在近葉梢處將導致大展弦比、大側斜和扭曲面元,這容易使槳葉表面速度的計算結果不正確,甚至會導致迭代過程發散及計算失敗.文中建立了一種「非常規網格」劃分方法,能有效地解決大側斜螺旋槳的計算和收斂問題.槳葉隨邊處通過迭代實現非線性等壓庫塔條件In this paper, the method of using infrared measuring for rotating component torque is studied, the key question of technology for rotating component infrared data transmission is analyzed and taking appropriate measures
本文研究了利用紅外線對旋轉構件扭矩進行遙測的方法,並對旋轉構件紅外數據傳輸中的技術關鍵問題作了分析並採取了相應的技術措施。Helical torsion springs - requirements for design, performance test method
螺旋扭力彈簧.設計要求和性能試驗方法This paper proposes a new algorithm for curvature calculation at discrete points, considering both total revolving and partial twisting of the fbg sensors in order to enhance the curve - fitting accuracy
該文提出了一種在光纖光柵傳感器基材整體旋轉或扭轉情況下得到離散點曲率的演算法,從而提高重建精度。分享友人