旋磨法 的英文怎麼說

中文拼音 [xuánmófǎ]
旋磨法 英文
hametag process
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  1. Veneer knife grinders - test and inspection methods

    旋板刀磨床.試驗和檢驗方法
  2. The shortage of this kind of system is that the mechanical frictional waste and noises are n ' t neglectable. this results in the low efficiency and the short life of the equipment so that it ca n ' t guarantee the reliability of the system for long term running

    過去，物流傳輸系統由旋轉電機驅動，其缺點是機械磨損和噪音較大，這使得設備的效率不高，使用年限不長，無法保證系統長期運行的可靠性。
  3. Based on the analysis of pulping movement of material in bivis extruder, a study on the designing theory of positive directional screw in bivis extruder had been carried out, the relationship between flow capacity and basic parameters of positive directional screw in bivis extruder was established, the designing method of negative directional screw was discussed, and a basic designing train of thought of the extruder was put forward

    摘要在分析雙螺桿磨漿機中物料磨漿運動的基礎上，對雙螺桿磨漿機的正向螺旋的設計理論進行了研究，建立了流量與雙螺桿機構正向螺旋的基本參數之間的關系，討論了反向螺旋的設計方法，提出了雙螺桿磨漿機設計的基本思路。
  4. This paper develops a mathematical model for the solution to the longitudinal tooth curve of an internal gear shaver based on the simplified principle for space transmission of a helical gear pair without flank clearance, and proposes a calculating approach of the profile modification of the grinding wheel to be used for grinding the longitudinal tooth curve of the shaver

    摘要用簡化的空間螺旋齒輪作無側隙嚙合傳動的原理，建立了求解內剃齒刀齒向曲線的數學模型，並給出了修磨這種齒向曲線的盤形砂輪的廓形計算方法。
  5. Rubber - determination of abrasion resistance using a rotating cylinderical drum device

    旋轉輥筒式磨耗機法
  6. ( 2 ) by using the methods of analytic geometry and mbs and parameter measure map along x - axes by 9 - line distinguish method, the formulas for correctly identifying the error parameters have been established

    （ 2 ）針對sk - 21數控磨床開展誤差參數檢測實驗，通過現場測量，獲得凸輪工作臺直線運動誤差和旋轉誤差數據，運用9線辨識法進行分析，經數學處理后為補償程序提供必要數據。
  7. I paints and varnishes - determination of resistance to abrasion - part 2 : rotating abrasive rubber wheel method iso 7784 - 2 : 1997 ; german version en iso 7784 - 2 : 2006

    色漆和清漆.耐磨性的測定.第2部分:旋轉摩擦橡膠輪法
  8. Test method for abrasion resistance of concrete or mortar surfaces by the rotating - cutter method

    用旋轉切割機法對混凝土或砂漿表面耐磨性的試驗方法
  9. This results in the low efficiency and the short life of the equipment. and for that, it ca n ' t guarantee the reliability of the system for long term running

    過去，由旋轉電機驅動的物流傳輸系統，機械磨損和噪音較大，設備的效率不高，使用年限不長，無法保證系統長期運行的可靠性。
  10. Standard test methods for wear testing rotary operators for windows

    窗磨損試驗旋轉操作器的標準試驗方法
  11. The good quality 425r silicate cement and 525 silicate cement, which are produced by the use of rotary kiln and up to the national standard gb175 - 92, are particularly suitable for the construction of buildings for civil use, airport, road, port, and dam because of its good early strength, quick condensation, good freeze and abrasive resistance, and low basicity content

    我公司出品的425r 525普通硅酸鹽水泥，系採用國濕法旋窯生產工藝，按國家標準gb175 - 92精心組織生產。具有早期強度高凝結硬化快抗凍性好耐磨性好含堿量低等特點，曾獲得福建省優質產品稱號。
  12. It is tested that the most proficiency method is using pulse - controlled magnet core to generate rotating magnetic field, in which the density and frequency of rotating field can be adjusted, the different form of rotating field can be easily achieved, and both magnetic pole and work piece need not rotate during the magnetic abrasive finishing process

    實踐證明，最有效的方法是脈沖控制電磁線圈的方法產生。這種類型旋轉磁場的強度和磁場的旋轉頻率都可以得到調節，磁場的不同旋轉形式也很容易實現，而且在研磨加工過程中工件和磁極都無需旋轉。
分享友人
分享到 Line

分享到臉書