曲強度 的英文怎麼說

中文拼音 [qūqiángdù]
曲強度 英文
flexural strength
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. Mechanical pencils. part 3 : black leads. bending strengths of hb leads

    機械鉛筆.第3部分:石墨. hb鉛筆芯彎曲強度
  2. By means of carrying out parameterization on finite element model of certain punching - welding bridge housing and through optimization analysis, this paper realized the light weighted optimization design of punching - welding bridge housing under the conditions of letting the bridge housing to satisfy the demands of perpendicular bending rigidity, the perpendicular bending strength and the perpendicular bending fatigue life

    摘要通過對某沖焊橋殼的有限元模型進行參數化，經過優化分析，使得橋殼在滿足垂直彎曲剛度、垂直彎曲強度和垂直彎曲疲勞壽命的條件下，實現了沖焊橋殼的輕量化設計。
  3. Laminated wood plastics. compreg determination of static bending

    木質層積塑料.靜曲強度的測定
  4. The products are suitable for the innovation of urban electrical network where its streets are narrow. it can effectively reduce the necessary height of the pole / tower, due to high bent resistant capacity, there will completely avoid the case that porcelain crossarm happen to crack. more, it can be well pollution resistant

    本產品適用於城網技術改造，能有效地利用城市狹窄的走廊面積升壓送電，可降底矸塔高度，由於其彎曲強度高，可防止瓷橫擔容易出現的斷裂事故，而且耐污性能好。
  5. Ebonite - determination of cross breakiing strength

    硬質橡膠彎曲強度的測定
  6. Test method for flexure of glass material

    玻璃材料彎曲強度試驗方法
  7. Cold - rolled flat products made of high yield strength micro - alloyed steels for cold forming - general delivery conditions

    由冷成形高彎曲強度微合金鋼製冷軋平板製品.一般交付條件
  8. Zirconia ceramics used in all - ceramic restoration of prosthodontics has shown favorable biocompatibility, chemical stability, flexural strength and color property

    摘要氧化鋯陶瓷作為口腔全瓷修復材料，在生物相容性、化學穩定性、抗彎曲強度和色澤等方面具有優勢。
  9. The flame - retardant and mechanical properties of the frp specimens with different fra ratio were investigated. it is shown that the oxygen index of the resin with the ratio of 15wt % of the fra reachs 28. the specimens are quenchable without any outer forces, however, the bending strength of the specimens decreases significantly

    研究了不同阻燃劑含量frp的阻燃性能和力學性能，結果表明，阻燃劑加入量為15wt %時， frp氧指數達到了28以上，使該材料達到自熄級水平，但其彎曲強度下降較大。
  10. The tension and bending strength of composites with wood flour content of 10 %, 30 % and 50 % respectively is all less than rps

    復合材料的拉伸強度和彎曲強度在木粉含量為10 、 30和50時低於rps 。 20和40木粉含量的復合材料的這兩項強度高於rps 。
  11. Abstract : the therortical calculation of the bending stress of the root and experimental stress analysis on the modified profile and the standard involute tooth profile were made with the finite element method and the electric resistance strain film method. this indicated that the modified profile was supe rior to the standard involute profiles in terms of the bending strength

    文摘:分別用有限元和電阻應變片法對修形齒形和漸開線齒形進行齒根彎曲應力計算與實驗應力分析.結果證明在彎曲強度方面修形齒形比標準漸開線齒形更優越
  12. Test method for cross - bending strength of vitrified pipe

    陶管彎曲強度試驗方法
  13. Here we obtain the strain compatibility method ande equilibrium of forces and concepts of fracture mechanincs, they can be used to predict the ultimats strength in flexure that can be achieved by such elements, given the cfrp cross - sectional area, or conversely, the required cfrp cross - sectional area to achieve a targeted resisting moment of rehabilitated flexureal elements

    Cfrp加固梁在承受彎曲荷載時的破壞是鋼筋屈服后碳纖維斷裂和鋼筋屈服后混凝土壓碎。本文通過應變相容方法和對破壞機理的定義，由給定的cfrp橫截面積預測加固梁的極限彎曲強度；或者相反，在已知加固梁的極限彎曲強度時可以求出所需的cfrp橫截面積。
  14. While the use of antistatic agents make the bending property of the specimens even worse, compared with that of the normal specimens

    採用偶聯劑kh - 570對玻璃纖維布進行表面處理，可使frp的彎曲強度恢復到改性前的水平，並使其沖擊強度提高。
  15. Basing on the discussion of the development status and the direction of block board in china and the key problem existing currently, this essay mainly discussed the research to the influential factors of bending strength about block board and its importance and necessity

    摘要通過對我國細木工板發展現狀、趨勢和目前存在主要問題的論述，探討對細木工板橫向靜曲強度影響因素研究的重要性和必要性。
  16. Test method for cross - bending strength of porous ceramic

    多孔陶瓷彎曲強度試驗方法
  17. Test methods for natural facing stones part 2 : dry and wet test methods for flexural strength

    天然飾面石材試驗方法第2部分:乾燥水飽和彎曲強度試驗方法
  18. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  19. Testing methods for flexural strength of adhesive bonds

    膠粘劑粘合點抗撓曲強度的試驗方法
  20. Textile glass - rovings - determination of flexural strength of rod composites

    棒狀復合材料彎曲強度的測定
分享友人
分享到 Line

分享到臉書