曲柄轉角 的英文怎麼說
中文拼音 [qūbǐngzhuǎnjiǎo]
曲柄轉角
英文
crank angle-
It is composed of two components : level move and rotation. level move is realized by the co - operation of oil vat, handspike and synchronizer. rotation is realized by the brace and the triangle oriented axis
平行移動是由液壓油缸推動，通過推動軸承傳到推桿、同步盤，並相互配合實現的；旋轉運動是由曲柄、三角架導向軸完成的。The sampling rate of the system can reach 3704 sps, and the crank angle is 1. 94 degree per sampling point corresponding to the crank speed of 1200r / min. in the mean time, the position signal of the piston could be collected by photo - electricity switch
本研究首先設計和實現了摩擦力採集電子電路系統，裝置最大采樣率可達到3704sps ，在曲軸轉速為1200r / min時，對應曲柄轉角1 . 94度采樣點，並且可以採集用來確定活塞位置的光電開關的信號。The existence of a c - c ( crank - crank ) type of geared five - bar linkages linked with the ground link, the classification and the range of gear ratio and phase angle in the fully rotatability of geared five - bar linkages were mainly studied in this dissertation
本論文主要研究了齒輪?五桿機構中與機架相連的兩連架桿的雙曲柄的存在條件、齒輪?五桿機構的分類以及在每一分類中齒輪?五桿機構能夠整周轉動時其相位角和傳動比的范圍。This article presents a mathematical calculation model of kinematic parameters for the unusual shape beam pumping unit by analyzing its geometry relationship and kinematic characteristics
異形游梁式抽油機的游梁后臂有效長度隨曲柄轉角而變化，故無法利用常規游梁式抽油機的解析方法來計算其運動參數。A model of letting out of no oil ubricated double whirlpools vortex air compressor was set up, the length of leak line of one cycle was calculated the change of the leak line at work, the change of the length of leak line varying with the crank corner, and the change of the leak amount varying with the pressure of revealing atmospheric and crank corner were analyzed
摘要建立了無油潤滑雙渦圈渦旋壓縮機的泄露模型，根據型線的幾何理論計算了一個周期內泄漏線的長度，分析了在工作過程中泄漏線的變化，泄漏線長度隨曲柄轉角的變化，以及泄露量隨排氣壓力，曲柄轉角的變代情況。The count method of the pressure ability and torque ability of crank press has been introduced with the relation of the two kinds ability of the crank press and force - angle curve gained by analyzing and computing the data of ja21 - 18 crank press ability
摘要介紹了曲柄壓力機的壓力能力、扭矩能力的計算方法，並通過對ja21 - 18型曲柄壓力機的能力分析計算，得出此種壓力機兩方面能力分別與力轉角曲線圖的關系。The dimensions of this hybrid mechanism is " from the result of the example in chapter 4. a rotary encoder is used to gather the position signal of the crank, according to which micro - computer control the rotation of the setup motor assembled with the other side link in order to adjust the position of this side link. only if we turn arbitrarily the crank connected to the rotary encoder, a given path is generated precisely
根據第四章中優化綜合得出的結果，製作五桿機構模型，採用一角度傳感器測得作主運動的曲柄的位置參數，由單片機根據此參數來控制與另一曲柄相連的步進電機的轉動，使連桿點精確再現給定的軌跡。分享友人