最低工作轉速 的英文怎麼說

中文拼音 [zuìdīgōngzuòzhuǎnsù]
最低工作轉速 英文
coil primary induced voltage
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 轉 : 轉構詞成分。
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 轉速 : speed; revolution; rotation rate; speed of revolution; rotating speed; rotational speed轉速指示器...
  1. Minimum operating speed

    最低工作轉速
  2. Optimal design with three variables is then done to the elbow - bar mechanism of the mp1040b moulding machine by utilizing the method of punishing function for constraint problems and variational scale for unconstraint problems. the optimal target function is the maxium of gradient in one work travel for the moulding plank of the elbow - bar mechanism. the result shows that the maximal gradient of moulding plank in one motion period declines by 25. 7 after optimization, and the angular acceleration of the bottom moulding plank decreases greatly

    動力學分析中，各構件的質量和轉動慣量是通過pro / engineer軟體，先建立各個構件幾何模型而求得；然後，利用解決約束問題的罰函數法和處理無約束問題的變尺度法對mp1040b型模切機肘桿機構進行三個設計變量的優化設計，優化目標函數為肘桿機構的下模切板在一個工作行程中達到的最大傾斜程度；通過優化設計，模切機肘桿機構的下模切板在一個工作行程中的最大傾斜程度降低了25 . 7 ，其角加速度明顯減小，提高了模切機動力學性能。
  3. Electromotor joins with high efficiency selected water pump, scm ( single chip micyoco ) control system commands water pump according to cooling water temperature which substitutes traditional strap - driving mechanism pump and forms tael - level intellectualized control cooling system combining with electromotion control of cooling fan. consequently it realizes that water pump and fan autoregulate with engine working status and assures t hat cooling water temperature keeps in the best range all the time and advances the reliability of engine working and realizes exact control of cooling water temperature in deed

    選用高效率水泵與電機聯接，改由單片機控制系統根據冷卻水溫控制水泵的工作，代替傳統的皮帶帶動的機械水泵，結合冷卻風扇的電動控制形成兩級智能化控制的冷卻系統，從而，實現了水泵和風扇轉速隨發動機工況變化的自動調節，真正實現了冷卻水溫的精確控制，保證了冷卻水溫始終保持在最佳范圍內，大量減少傳熱損失降低油耗，並提高了發動機工作的可靠性。
  4. Driver ' s position : optimised layout, based on the latest ergonomic principles, considerably reduced vibration and noise, throunh insulating the operator ' s compartment from the vehicle itself by means of shock absorbes, seat adjustable to operator ' s height and weight, as well as being spring suspended and hydraulically damped. lindedouble pedal control system offers accurate reversing without. changing gear. linde central control lever operates all mast functions

    駕駛室:根據人機工程學原理對駕駛室進行了優化設計.駕駛室與車身之間由減震墊隔離，大大地降低了震動和噪音，司機座下有彈簧和液壓減震裝置，並可根據駕駛員的身高和體重進行調整，以獲得最舒適的狀態.林德雙踏板控制系統具有無需切換即可實現靈敏向的功能:林德集中控制桿控制門架的提升，下隆和傾斜動作.發動機的轉速可根據提升和其它功能對輸出功率的需要而自動調節.護頂架與司機座聯成一體，並可裝配成舒適的全封閉駕駛室
  5. Because a hybrid ' s battery and motor can provide the boost required for acceleration or hill climbing, engineers can both downsize the car ' s engine and optimize it to run only at high - efficiency operating points that burn much less gas

    由於混合車的電池和馬達可提供加速或爬坡所需的額外馬力，因此工程師可以縮小引擎，設計讓引擎只在耗油率最低的高效率運作點附近運轉。
  6. The air - fuel ratio closed loop control adjusts the air - fuel ratio near the theoretical value by controlling the supplementary air of supplementary valve based on the signals of oxygen sensor, running speed and water temperature and which is necessary condition for three - way catalyst converter to work more efficiently

    空燃比閉環控制是根據氧傳感器、轉速和水溫信號，控制化油器后補氣閥補氣將空燃比控制在理論值附近，為三元催化轉換器高效工作準備必要條件，使其最大限度降低尾氣排放。
  7. Aim at the dtc ' s blemish mentioned above and the direction of dtc technique development, the dissertation put great emphasis on the work as follows, with an eye to exalt dtc system function : ( 1 ) a new speed - flux observer of an induction motor is proposed to enhance the accuracy of flux observing, which is an adaptive closed - loop flux observer and different from the traditions. a new adaptive speed - observation - way is deduced out according to the popov ' s stability theories ; ( 2 ) to improve the performance of dtc at low speed operation, we have to exalt the accuracy of the stator flux estimation and a new way of bp neural network based on extended pidbp algorithm is given to estimate and tune the stator resistance of an induction motor to increase the accuracy of the stator flux estimation ; ( 3 ) digital signal processor is adopted to realize digital control. an device of direct torque control system is designed for experiment using tms320lf2407 chip produced by ti company ; ( 4 ) bring up a distributed direct torque control system based on sercos bus, sercos stand for serial real time communication system agreement which is most in keeping with synchronous with moderate motor control ; ( 5 ) the basic design frame of the hardware and software of the whole control system is given here and some concrete problem in the experiments is described here in detail

    針對上面提到的直接轉矩控制的缺陷和未來直接轉矩控制技術發展方向，本論文重點做了以下幾個方面的工作，目的在於提高dtc系統的綜合性能： （ 1 ）提出一種新型的速度磁鏈觀測器，新型的速度磁鏈觀測器採用自適應閉環磁鏈觀測器代替傳統的積分器從而提高磁鏈觀測的精度，並且根據popov超穩定性理論推導出轉速的新型自適應收斂律； （ 2 ）改善系統的低速運行性能，主要從提高低速時對定子磁鏈的估計精度入手，提出了一種提高定子磁鏈觀測精度的新思路? ?利用基於bp網路增廣pidbp學習演算法來實時在線地修正定子電阻參數； （ 3 ）採用數字信號處理器dsp實現系統全數字化硬體控制，結合ti公司生產的tms320lf2407晶元，設計了直接轉矩控制系統的實驗裝置； （ 4 ）提出了基於sercos總線網路化分散式的直接轉矩控制系統， sercos （ serialrealtimecommunicationsystem ）是目前最適合同步和協調控制的串列實時通信協議； （ 5 ）基本勾勒出整個控制系統的硬體和軟體設計基本框架，詳細描述一些實驗中的具體的細節問題。
  8. As a hardware. the gimble servosystem design is very important in the making of the optoelectronic tracking system. the precision of the position. speed and the speed stability are the key indexes. for the optic measurement system in the high space. the minimum stable speed and high precision are needed

    轉臺伺服系統的位置精度，速度精度和速度平穩性是光電跟蹤系統設計的重要指標，而對深空光測系統，則要求其具有穩定的最低速度以及低速時高的工作精度。
  9. Compared with traditional sensors, the saw sensors can be used for wireless passive sensing with no need for a separate power supply, which makes it possible to measure parameters of fast moving or rotating objects. in addition, wireless passive sensing in extreme environment likes strong electromagnetic interference and low temperature becomes obtainable

    與傳統傳感器相比，其最大優勢在於它能實現無源無線遙測，這使得它能運用在諸如快速移動物體、旋轉體等無接觸測量中，並且在強電磁干擾、低溫等極端工作條件下也能正常工作。
  10. Lowest continuous speed test with load

    最低穩定工作轉速試驗
  11. Lowest continuous speed with load

    最低穩定工作轉速
  12. This system is realized by cpld which can get rid of the disadvantages in one - time design including property liable to jamming, long sampling period, and poor working stability. its sampling period is up to 500ns at least and output delay is only 19. 5ns. a stable period of pulse coming out of quadruple - frequency differential circle belongs to it

    完成了用vhdl硬體描述語言對全數字轉速位置測量子系統的設計，並用max ? plusii軟體進行了編譯和波形模擬，在cpld （ max7000 ）得到實現，該系統克服以往設計中存在的易受干擾、工作穩定性差、采樣周期太長等的缺點，輸出延時僅為19 . 5ns ，采樣最低周期可達到500ns ，且四倍頻微分電路獲得的脈沖周期穩定。
分享友人
分享到 Line

分享到臉書