最大功率輸送 的英文怎麼說
中文拼音 [zuìdàgōnglǜshūsòng]
最大功率輸送
英文
maximum power transfer- 最 : 副詞(表示某種屬性超過所有同類的人或事物) most; best; worst; first; very; least; above all; -est
- 功 : 名詞1 (功勞) exploit; merit; meritorious service [deed]: 戰功 military exploits; 立功 render me...
- 率 : 率名詞(比值) rate; ratio; proportion
- 輸 : Ⅰ動詞1 (運輸; 運送) transport; convey 2 [書面語] (捐獻) contribute money; donate 3 (失敗) l...
- 送 : 動詞1 (運送; 傳送) deliver; carry 2 (贈送) give as a present; give 3 (伴送; 送別) see sb of...
- 輸送 : deliver; supply; carry; transport; convey; feed; transmit; transfer; transportation; delivery
-
Based on the analysis of designed cad graphics and the given parameters, computer can convert the cad graphics to a acdbpolyline which can simulate the routine of the conveyor chain. then by using the method of point - by - point strain calculation, computer could figure out each point ’ s strain of the chains under different load states, and get the results such as strain ’ s maximal and the minimal values and their positions, weight of the strain equipment and power of the drive electric - machinery that the conveyor need
通過對設計的cad圖形和給定參數的分析,將輸送鏈運行軌跡轉化為一條可模擬輸送鏈軌跡的多義線,然後用逐點張力計演算法動態地計算出各種加載狀態下輸送鏈上各點的受力,得出最大、最小受力點的力的大小和位置,拉緊裝置的重量,驅動電機所需的功率等結果。The thesis presents a new method to calculate transient stability limit, describing the calculation problem as a best parameters selection problem, with an object of largest transport power on transmit lines and constrains of static variables and transient stability
本文將求解暫態穩定極限問題描述為一個以輸電線路或輸電斷面輸送功率最大為目標,以靜態運行變量及暫態穩定為約束條件的最優參數選取問題。Sszm500b straight line double edgers, and 90transfer taboe. 26 spindles on each sszm2500b. plc control system sets processing parameters via interface, and finishes processing at one time. this product has stable structure. precise and smooth transmission system, thetransmission belt drive adopts strong power and transfrequency motor to control speed, constant power, constantrele output and advanced epuipment to control, high polishing efficiency. it is the best matched equipment of large batch of furniture and decorated glass edge production, and production, and can be matched with gluing, printing, reinforcing, etc. production line
才用plc控制系統通過界面設定加工參數一次完成加工,具有穩定扎實的底座結果精確流暢的傳動系統,傳送皮帶驅動採用大功率變頻電機調速控制,恆功率恆扭矩輸出和高配置的控制。結構緊湊,性能穩定可靠,拋光及生產效率高。是大批量的傢具和裝飾玻璃的磨邊生產的最佳配套設備,可以與夾膠印花鋼化等生產線配套使用。Meanwhile, we have gained some achievement. 1. based on error variety of nonlinear control curves of ld output laser power by optoelectronic feedback measured, we take advantage of window pid control algorithm to gain high stability of laser power and reduce error amends at mostly
1 、基於光電池檢測ld光功率輸出的非線性控制曲線產生的誤差變化,將特性曲線利用軟體的窗口控制演算法實現區域控制,進而有效的對ld工作電流進行pid穩態控制和光功率參數顯示,且激光器的光功率輸出和激光通過分光鏡後送入光電池放大電壓量和單片機通過計算使到誤差修正量達到最小,從而使光功率控制達到最佳效果的變化關系。Future mobile communications have to support the transmission of high rate data and multimedia applications in the radio spectrum, which is already extremely scarce. the basic idea of adaptive coded modulation is to maintain a constant throughput by varying the transmitted power level, symbol transmission rate, constellation size, coding rate or any combination of these parameters. thus, without sacrificing bit - error rate ( ber ), these schemes provide high average spectral efficiency by transmitting at high speeds under favorable channel conditions, and reducing throughput as the channel degrades
自適應編碼調制( adaptivecodedmodulation , acm )的基本思想是在不犧牲系統傳輸性能(比如ber )為代價的前提下,通過單獨改變發送功率、波特率、編碼方案、碼率、調制方式,或者是綜合改變前面所述的各種參數,在有利的通道條件下,獲得較大的吞吐量,當通道質量下將時,相應地降低傳輸速率,最終達到提高平均頻譜效率的目的。Heating boilers. part 4 : heating boilers with forced draught burners. special requirements for boilers with forced draught oil burners with outputs up to 70 kw and a maximum operating pressure of 3 bar. terminology, special requirements, testing and marking
供暖鍋爐.第4部分:有強制送風燃燒器的供暖鍋爐.輸出功率在70kw以下最大工作壓力為3巴的帶強制通風燃燒器的供暖鍋爐的特定要求.術語特定要求試驗和標記分享友人