最大斷裂載荷 的英文怎麼說
中文拼音 [zuìdàduànlièzǎihé]
最大斷裂載荷
英文
maximum breaking load- 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
- 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
- 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
- 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
- 荷 : 荷名詞（蓮） lotus
- 斷裂 : break; disrupt; flying off; fracture; fragmentation; out break; rift;crack;bursting;rupture;rendi...
- 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
-
Results showed that the curves of fatigue / creep have three stages at the 75 % stress and the curves of fatigue / creep have two stages at the 55 % stress
結果表明，在交變載荷最大值為75 %的應力水平下，其疲勞蠕變斷裂曲線為3段式曲線；在55 %的應力水平下， 15小時內其疲勞蠕變曲線為兩段式曲線。Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure
試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。Breaking life lessens when the maximum load time is longer
隨著最大載荷保持時間的增加，層合板的斷裂壽命降低。
分享友人