最大法向應力 的英文怎麼說

中文拼音 [zuìdàfǎxiàngyīnglì]
最大法向應力 英文
maximum normal stress
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  1. Choose two nodes on the edge of the structural to compare the results calculating by the finite element program midas, then we can draw a conclusion that these kinds of space truss systems is sensitive to the libration of the dynamic wind loads. to consider this factor is very necessary in the process of design, we will use the pulsant augmentation coefficient to realize it

    比較靜力風荷載和動力風荷載作用下的有限元軟體的計算結果，選取結構邊緣部分的兩個節點，對比它們在兩種方法計算下的最大位移的計算結果。經過比較可以看出重量輕、頻率低、阻尼小的柔性建築物對風荷載的橫向振動是很敏感的，在進行工程設計時應該考慮這種因素，並可採用乘以風振系數等相應方法來加以體現。
  2. It ' s indirectly proved that the oriented method is a reliable and practical. moreover, the natural fracture direction tested by the underground microseismic monitoring system also proved that the orientation technique is correct and comparable. 6

    同時，針對該試驗區塊，對兩口開發井進行了地下微地震波監測，測得的人工裂縫方位與實驗測得的最大主地應力方向非常吻合，進一步證明了該方法的正確性和可比性。
  3. Obtain these chief research achievements. ( 1 ) the method of hydraulic fracturing, kaiser effect experiment and the finite element numerical simulation computation results, the direction of maximum horizontal principal stress intersect the small - angle of tunnel axial line, it is favorable to the stability of tunnel peripheral rock ; according to the test rust of field stress - relief method, at the present time, zhe gu mount tunnel have n ' t access to high crustal stress site, maximum principal stress magnitude is 17mpa ~ 20mpa

    主要獲得以下研究成果： （ 1 ）綜合水壓致裂法、室內巖石kaiser效應試驗和有限元數值模擬計算研究成果，最大水平主應力方向與隧道洞軸線小角度相交，對隧道圍巖穩定性有利；根據現場應力解除法測試結果，目前鷓鴣山隧道尚未進入高地應力段，最大主應力量級為17mpa 20mpa 。
  4. For the stress analysis of dryers under the line load of supporting rollers, according to hoff theoretical solution of thin cylindrical shell under line loads, mangelsdorf approximate solution is modified on the basis of the calculation analysis for 14 sets dryers " dimension by computer programming with matlab software. the approximate formulas of the second largest hoop stress of the middle section of the shell are derived

    針對托輥線壓載荷作用下烘缸的受力分析，本文根據薄壁圓柱殼在線壓載荷作用下的hoff理論解，在運用matlab軟體對14組常用烘缸參數進行編程計算分析的基礎上，對mangelsdorf近似解作了修正，並由最小二乘法導出殼體中部截面環向應力次大值的近似計算式。
  5. Through the physical model experiment, the wave forces over submerged dyke and transmission coefficient are analyzed under the action of regular wave. in the test of wave forces, the rectangle - type submerged dyke is used as research object, and when analyzing the total wave forces, the effect of water depth before the dyke and that of the wave parameters is considered. based on the test, through the methods of multi - element linear regression, experimental formulae are given to calculate maximum total wave forces in horizontal direction, its relative vertical wave forces and maximum wave forces before and after the dyke, which are compared with the present formulae

    在潛堤波力的研究中，選取矩型潛堤作為研究對象，在分析各個影響因素對潛堤波力影響的基礎上，選取兩個最主要的影響因素，即相對波高和相對水深作為研究重點，在物理模型試驗結果的基礎上，定性地研究分析了潛堤所受的總波力隨相對波高和相對水深的變化規律，並在此基礎上，利用多元線性回歸的方法，分別給出了在本文試驗條件下計算潛堤最大水平總波力及其相對應的垂向總波力的經驗公式以及計算堤前堤后最大總波力的經驗公式，並與已存在的計算公式進行了對比。
  6. The main body of the dissertation is from the second section ( the first chapter ) to the fifth section ( the fourth chapter ), which firstly discusses the evolvement of american economic recovery policy toward japan and argues that the economic recovery policy toward japan was the inevitable result which the united states pursued her global containment strategies, with the changes of the international situation and the economic conditions in japan, the u. s. regarded japan " s accession to gatt gradually as the most important objective of the economic recovery policy toward japan ; secondly explains in detail that the u. s. fought up against the old guard in congress persistently in order to win the authorization from reciprocal trade agreements act ( rtaa ) so as to conduct the crucial tariff negotiations with japan, and emphasizes mainly that the executive had to seek for the balance between the national interest and oversea interest because of the strong forces of the domestic protectionism group, but made efforts to make foreign economic policy which is favourable to the latter because of the need of the cold war strategies ; thirdly analyzes the basic contents of u. s. - japanese tariff negotiations briefly and summarizes the results of the negotiations, and considers that under a large number of concession which the u. s. made in the negotiations, the japanese could change american political and strategical interest into the japanese trade interest and became the main winner ; fourthly researches mainly british diplomatic policy towards japan " s accession to gatt and american reaction to the policy and influence on it, and american roles in

    第二部分（第一章）至第五部分（第四章）是論文的主體部分，首先論述美國對日經濟復興政策的演變歷程，提出美國對日本的經濟復興政策是美國推行全球冷戰戰略的必然結果，隨著國際形勢和日本經濟狀況的變化，美國逐漸將推動日本入關視為對日經濟復興政策的最重要目標；其次詳細闡述為了獲得《互惠貿易協定法》的授權，以便與日本進行重要的關稅談判，美國政府和國會保守派持續不斷地作斗爭，重點強調，鑒于國內貿易保護主義勢力的強大，行政部門不得不尋求國內利益和海外利益的平衡，但同時出於冷戰戰略的考慮，又盡量使對外經濟政策向後者傾斜；第三，扼要分析美日關稅談判的基本內容，並總結關稅談判的結果，認為美國政府在談判中對日本政府所做的大幅度讓步，使得日本人能夠將美國的政治、戰略利益轉化為日本的商貿利益，從而成為談判的最大贏家；第四，重點研究英國對日本入關的外交政策和美國對該政策的反應、施加的影響，在國際斗爭中美國為日本入關而發揮的作用以及日本人自己做出的努力，指出雖然在美國施加的強大壓力下，英國政府最終同意日本成為關貿總協定的成員國，但是它依然以國家利益為重，對日本援引關貿總協定第35條，不給予其商品最惠國待遇。 」
  7. Depending on how the ground surface is denuded, the feature of the current crustal stress field and rock stress environment can be calculated analyzing the result in this paper : by analyzing the recovering feature of the elastic deformation of the rockmass in unload - stage under various pressures, it has been found there is close relationship between the recovering degree of the elastic deformation of the rockmass and the unloading degree of the pressure the direction of the major principal stress in the crustal stress field is not consistent with the direction of the crushing stress regional tectonics borne during the last tectonic movement. the evolving degree of the regional geomorphology evidently affects the current crustal stress field, which changes from the self - weight stress field to the horizontal stress field, with the changing of the eroding degree of the regional geomorphology ranging from valley area to hilly country to flat country. in valley area, where there is two stress belts, the bankslope s tress belt and the self - weight stress belt within the mountain. the direction of the major principal stress is nearly parallel to the ground surface and inclines towards the valley in the bankslope stress belt. it is nearly vertical in the self - weight stress belt

    通過本文的研究成果，根據區域性地貌的演化特徵，我們可以大致地對現今地應力場進行判斷：在分級卸荷條件下，巖體中彈性變形的恢復具有明顯的規律性，這種規律對于研究地應力場的演變是有幫助的；地應力場中最大主應力方向與區域構造形跡在最近的構造運動中所受區域性擠壓應力的方向無明顯的對應性；區域性地貌形態的演化程度對現今地應力場的特徵具明顯的影響，隨著區域性地貌侵蝕程度由峽谷區、丘陵區、平原區的變化，現今地應力場特徵由自重應力場、水平應力場為主含少量自重應力場特徵向水平應力場的規律變化；在峽谷區，山體中具有兩個應力帶：自重應力帶和卸荷應力帶，最大主應力方向在卸荷應力帶中近平行於坡面並傾向于河谷、在自重應力帶中近於直立；根據原始地面遭剝蝕的程度，可以大致地估算最大主應力和中間主應力的量值和方向；在丘陵區和平原區，最大主應力的方向近於水平，並與附近區域性侵蝕盆地和河流的展布方向基本平行，根據原始地面遭剝蝕的程度，可以大致估算其最大主應力的量值；根據區域性地貌形態的特徵來分析工程區的現今地應力場特徵，並進而大致了解巖石的應力環境，這種分析方法得出的結論與許多實際的地應力測試成果基本一致，對于大型水電工程地下廠房和壓力隧洞的設計是有所幫助的。
  8. When a ferromagnetism items is under the application of stress, the phenomenon that the tangential component of magnetic leakage field has maximum value and that the normal component of magnetic leakage field changes polarity and acquires zero value at the stress concentration zone will take place

    鐵磁性工件在受到應力作用時，在應力集中處會有漏磁場的切向分量出現最大值、同時法向分量改變符號且過零值點的現象。
  9. ( 三 ) under the dynamic load of the explosion, the numeric analysis has been done and achieve the rule as follow : ( 1 ) when the frequency of vibration is 0. 3hz, the acceleration of the slopes top gets the maximum ; so 0. 3hz is believed the natural frequency of the slope as a whole ; ( 2 ) the vibration of explosion can been magnified because of the condition of the landform, when the relative altitude is up to 45m, the acceleration of horizon gets the maximum ; when the relative altitude is up to 100m, the absolute value of acceleration and the deformation of horizon is larger than that in the bottom of the slope ; ( 3 ) in the period of forced vibration, at the top of the slope, the acceleration of horizon become larger and larger ; at the middle part of the slope, it becomes smaller ; ( 4 ) when the explosion velocity of is much little, the shallow part destruction is the primary deformation of the slope

    （三）採用模態疊加法針對爆破動力作用，進行邊坡的動力響應分析，得出了以下結論： （ 1 ）振動頻率為0 . 3hz時，坡面頂部水平向加速度峰值最大；綜合考慮，可認為該邊坡的自振頻率為0 . 3hz左右； （ 2 ）地形對爆破地振動存在放大作用，研究剖面的坡面，水平向加速度及位移在地形相對高差45米左右最大，而後隨相對高差的增高而減小，相對高差為100米時，水平向位移及加速度絕對值均大於坡腳； （ 3 ）強迫振動段，水平向加速度值隨時間變化的規律為：坡頂節點總的變化趨勢是越來越大，而坡體中部節點的變化趨勢是越來越小； （ 4 ）當爆破振速較小時，變形破壞的形式表現為坡頂表面滑塌型。
  10. Then, taking into account the effect of the compression of the approach roadway and the differential slope of the bridge slab, the author analyzes the dynamic response of man - vehicle - road system when the vehicle approaches and leaves the bridge by means of laplace transform, the curve of man ' s acceleration versus time, the vertical force between the vehicle and road versus time, the man ' s maximum transient vibration value and the maximum force between the vehicle and road are got, and the program about the calculating progress above are edited. based on the analysis above, the influence on the maximum transient vibration value of some parameters about the vehicle and road such as the movement direction and speed and weight of the vehicle, the differential slope of the bridge slab and the length of the approach slab, are studied, and some conclusion are given

    分上橋和下橋兩種情況，考慮車路耦合和橋面沉降坡差的影響，對車輛通過設和不設搭板的路橋過渡段時「人?車?路」系統的相互作用用拉普拉斯變換法進行了動力響應分析，得到了人的加速度及路面對車的垂直作用力隨時間的變化曲線、人的加速度最大瞬態振動值和路面對車的最大作用力，分析了車輛的行進方向、速度和載重，橋面沉降坡差和搭板長度等車和路各參數對計算結果的影響，並編制了相應的計算程序。
  11. According to the effective field expression which has been derived in former, the phenomenon that the tangential component of magnetic leakage field has maximum value and the normal component of magnetic leakage field acquires zero value at the stress concentration zone of positive magnetostriction ferromagnetism materials under the application of tensile stress and negative magnetostriction ferromagnetism materials under the application of compressive stress is explained theoretically through analyzing and discussing

    根據所得到的地磁場中受力鐵磁性材料有效場表達式，通過分析討論，解釋了受拉力作用的正磁致伸縮鐵磁材料和受壓力作用的負磁致伸縮材料在應力集中處漏磁場切向分量出現最大值、同時法向分量為零值的現象。
  12. A bearing surface transmits the interaction between an arch dam and its foundation, the strength of which directly affects the constraint of the bedrock to the dam, and thus affects the stress and deformation of the dam. the influence is studied in this paper with nonlinear finite element method, as an example, for a high arch dam in design. the results show that the influence on stress is only limited within the local area near the bearing surface, larger on the maximum principal tensile stress than on the principal compression stress, and the decrease of the strength does not cause unlimited increase of the maximum stress. the influence on the displacement of the top of the dam is smaller than that of the bottom of the dam, especially the relative downstream displacement. at the lower strength of the bearing surface, the relative downstream displacement at the bottom of the dam increases with the decrease of the strength

    建基面是傳遞拱壩和基巖相互作用的紐帶，它的強度直接影響基巖對壩體的約束，從而影響壩體的應力和變形.採用非線性有限單元法，以設計中的某高拱壩為例，分析建基面強度對壩體應力和變形的影響.結果表明建基面強度對壩體應力的影響僅限於建基面附近的局部范圍，對最大主拉應力的影響要大於對最大主壓應力的影響，建基面強度的降低不會無限地增大壩體的應力數值；建基面強度對壩頂位移的影響較小，但對壩底位移（尤其是順河向相對位移）的影響較大，當建基面強度較低時，壩底順河向相對位移隨建基面強度的降低而增大
  13. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  14. At first, the mechanical model of joint is discussed, and the constitutive relation of the rough joint, especially the bolt - supported joint, is given. then bedding slide of bedding stratified rock slope is studied adopting limit equilibrium method, and a formula of stability is brought forward. at last, the bedding stratified rock slope ' s buckling deformation and failure mechanism and its evaluating method of stability is investigated, a corresponding mechanics model is established, then detail research to this failure mode is made in theory combining the energy law and elastic stability theory of plate and beam, and an analytical solution of the yielding curve is educed from this model

    文中首先對結構面的力學模型進行了一定的探討，提出了粗糙結構面尤其是加錨結構面的本構關系；然後採用極限平衡法，研究了順向層狀巖質邊坡的順層滑動失穩，提出了其穩定性計算公式；最後，結合能量定律和彈性板梁穩定理論，探討了工程中常見的順向層狀巖體邊坡潰屈失穩時的破壞機理、變形規律和穩定性定量評價方法，建立了相應的力學模型，求出了其相應的解析解，並提出了臨界坡長與最大彎曲位置的確定方法。
  15. All the results of axial and radial deformation measurement by digital image processing technique and those by traditional method are compared. the differences of the soil parameters on duncan and chang ' s nonlinear model made by these two methods are analyzed. finally, a compress test results and fem results are provided to show the reasonability and veracity of digital image processing technique to study the soil stress - strain characteristic in triaxial test

    （ 2 ）三軸試驗土樣局部變形研究：首先定量比較了三軸試樣沿高度方向不同位置的局部變形（局部徑向變形與局部軸向變形）大小，分析了三軸試樣局部變形的特點和影響因素；然後把三軸試樣數字圖像測量結果與傳統測量結果進行比較，以鄧肯張非線性模型為例進行了模型參數的整理，分析了兩種不問測量方法引起的參數差異：最後用原型壓縮試驗對比有限元數值計算結果，驗證了數字圖像測量方法得到的三軸試驗土體應力應變參數的合理性和準確性。
  16. At first, ploygon aggregate structure of concrete is randomly generated in two - dimensional plane with monte carlo method on the meso - level. then, the growth process of a crack of concrete 3 - point bending beam specimen is analyzed by fem, according to the criterion of maximum circumferential tensile stress. and the path of crack to spread in mortar, aggregate and interfaces of them is gained by the ultimate fracture criteria in construction standard that the width of crack should not be more than 0. 2mm

    首先，在細觀層次上，根據蒙特卡羅隨機抽樣原理，在二維平面上建立了混凝土多邊形隨機骨料結構模型，然後採用有限元計算方法，根據最大周向正應力準則，對三點彎曲梁構件進行了開裂過程的模擬，並以建築規范中構件裂縫小於0 . 2mm的要求為最終破壞標準，得出了裂紋在基質、骨料及界面的擴展路徑。
  17. Maximum normal stress

    最大法向應力
  18. And the best scheme among them has been proposed. in the last, with design opt of ansys, assigning roof plate ' s and base plate ' s thickness as design variables, making them meet the constraints of displacement of roof plate and base plate, and assigning the maximum stress of the structure as the goal function, the pile - boots structure has been optimized

    最後利用ansys自帶的優化求解器designopt ，以對樁靴結構強度和變形影響較大的頂板和底板厚度為設計變量，在滿足重要部件?頂板和底板豎向位移的約束條件下，把結構的最大等效應力設為目標函數，採用一階優化方法，對樁靴結構進行了優化設計，並得到了最優解。
  19. In order to fully develop the theory of squeezed branch piles, in particular, the justification of its superior performance in terms of the bearing capacity and sinking displacement, we have derived the analytical formulas of the axial load and the strain at arbitrary depth ; based on existing static loading test results and research on belled pile, together with the analysis of on - site testing data, we have applied the expand theory on sphere holes to the computation of radial stress of squeezed branch piles under hole expansion ; taking the oil pressure of hole expansion in to account, we have find the a branch force under certain hole pressures, hence we can estimate the maximum bearing capacity of single piles ; we have introduced the experiential formulas for the bearing capacity of squeezed branch piles based on its stress characteristic and pile testing data ; we have also done numerical simulations of squeezed branch piles utilizing finite element method software ansys ; we have matched the simulation res ults with those of on - site basic load experiments, regenerating the distributions of stress fields and strain fields of squeezed branch piles, and from those distributions, we can determine the optimal distances between plates and piles

    為了完善支盤樁的設計理論，探求支盤樁高承載力和低沉降量的內涵，本文推導出了支盤樁任意深度的截面荷載以及位移隨深度變化的理論公式；基於已有的靜載試驗成果及有關擴底樁的研究成果，從對現場測試數據的分析，將球形孔擴張理論引入到支盤樁擴孔時徑向應力的計算，考慮到擴孔時的油壓數據，求得某一孔壓下的支盤力，據此估算單樁極限承載力；同時根據對支盤樁的受力特點和試樁數據的分析，提出了支盤樁承載力計算的經驗公式；用有限元分析的方法，利用大型有限元分析軟體ansys對支盤樁進行數值模擬，並將模擬結果同現場的靜載試驗結果進行對比，再現了支盤樁在荷載作用下土中應力場和位移場的變化，根據應力場和位移場的變化范圍，指出最佳盤間距和樁間距；為支盤樁的設計和施工提供了一個可量化的設計依據。
  20. Based on the minimum potential energy principal, the influences of three loads, which are concentrated force, trapezoidal load and sinusoid load, over shear lag of cantilever single - box - single - cell box girder are deducted and discussed, and a conclusion is reached, which has some instructive significance for designer to determine the sectional dimension and reinforcing bars ; the bending normal stress changes greatly as considering the shear lag effect

    以最小勢能原理為基礎，推導並討論了3種形式的荷載：集中力、梯形荷載、正弦形荷載對懸臂單箱單室箱形梁剪力滯的影響，得出考慮剪力滯效應后彎曲法向應力有較大變化的結論，對設計人員確定截面尺寸、截面配筋具有一定的指導意義。
分享友人
分享到 Line

分享到臉書