最小壁厚 的英文怎麼說
中文拼音 [zuìxiǎobìhòu]
最小壁厚
英文
minimum wall thickness (mini w. )-
Taking thickness of web members and main chords as design variables and the lightest weight of crane booms as objective junction, considering constraints of rigidity and stability etc., this paper establishes the math model of optimal design
摘要選取起重機臂架的腹桿壁厚和各節臂架的主弦桿壁厚為設計變量,以最小重量為優化目標,考慮剛度和穩定性等約束條件,建立優化數學模型。Steel casting : 20 tons arc - furnace steelmaking, 40tlf refiner furnace ; the max elevating capacity 125t ; the max casting products 80t, dimension of casting products length, width, high 8. 54. 53m, spun casting min outer diameter, min wall thickness, max length 1000154000mm ; various specification steel strands
鑄鋼: 20t電弧煉鋼爐40tlf精煉爐最大起重能力125t最大鑄鋼件80t鑄鋼件最大尺寸長寬高8 . 54 . 53m離心澆注最大外徑最小壁厚最大長度1000154000mm各種規格連鑄坯。4. calculate the engaging distance between inserts and slots and the least thickness from bearing to contour of cone automatically. 5
自動計算相鄰牙輪之間牙齒與齒槽的最小嚙合間隙和牙齒底部到牙輪內孔的最小壁厚。Its reliability has been tested though examining. the influence laws of mould structure, including wiper die and the style, size and installed position of mandrel, have been studied. combined with the theoretical analysis of perfect pure bending, the tendency of relative bending radius r / d and relative wall thickness t / d to one of the major quality target - the maximum wall thickness reduction ratio is also studied
通過數值模擬研究獲得了包括防皺塊和芯棒形式、尺寸和安裝位置在內的模具結構對製件成形質量的影響規律;結合對理想純彎曲的理論分析,研究獲得了相對彎曲半徑r / d 、相對壁厚t / d對製件主要質量指標之一的最大壁厚減薄率的影響趨勢和大小。The production ability of thin steel sheet in china is promoted. however, limited by the ability of production and anti - corrosion, the limitation of the minimum thickness could not fulfill the requirements of the development
隨著生產的發展,我國薄鋼板的生產能力已大大提高,限於生產能力和防腐能力而對最小壁厚作出的構造限制已不符合當前生產和技術發展的需要。The minimum thickness of the workpieces
零件的最小壁厚The chinese codes stipulate both the width - thickness ratio and the minimum thickness of the elements. that is stricter than the stipulations of north american codes
對于受壓板件的壁厚,我國規范採取的是既限制板件寬厚比又限制最小板厚的規定,其限制較北美同類規范偏嚴。On the premise of satisfying all constraint conditions stipulated in the codes with the pipe thickness spacing, height and thickness of stiffener rings as variables and the total steel quantity per meter of pipe as objective function, the program is developed for structural stress computation and comparison of total steel quantity used so as to select the alternative with smallest total steel quantity per meter of pipe
該程序在滿足規范規定的各種約束條件下,以管壁厚度、加勁環間距、高度和厚度等作為變量,以每米鋼管的總用鋼量為目標函數,進行結構應力計算和工程量比較,從中選出用鋼量相對最小的設計方案。J9l7 ^ cad, cae, cam, icax, idesign, 模具, 設計, 招聘, 培訓 use uniform wall thicknesses throughout the part. this will minimize sinking, warping, residual stresses, and improve mold fill and cycle times
零件整體壁厚保持均勻.這樣可以最小化縮坑,翹曲,強度減小,模具填充和循環時間4 main parameters of the pcc pile such as length of pile, diameter of pile, rigidity of pile, wall thickness of pile are analyzed by the method of the thesis. the calculation results indicates that most markedly factor is pile diameter, in the next place pile length and property of ground soils, the impact of rigidity and wall thickness of pile are relatively little
4 、運用本文的方法對影響pcc樁水平承載性狀的主要參數進行了有限元數值模擬試驗計算分析,分析結果表明對pcc樁水平承載性狀影響因素最大的是樁徑,其次是樁長和地基土的性質,而樁身剛度和樁身壁厚的影響相對較小。分享友人